Documente Academic
Documente Profesional
Documente Cultură
56-1520-214
.. .
g. Packaging, Unpacking, and Storage Area. This area should be totally inclosed, .and it should be insured that there are no environmental conditions detrimental to the components. h. Airfield Requirements. Suitable airfield facilities shall be provided including airspace available to perform maintenance fight testing as specified in Chapter 5. medown and ground run up areas must also be provided. 2-2. Tools and Equipment. Tools and equip ment required for overhaul are listed in table 2-2 and 2-3 of this DMWR. Component tools and equipment are included in the applicable publications listed in Appendix A. 2-3. Special Tools and Equipment. Table 22 is a list of special tools and equipment by no-
menclature, part .number, Federal Manufacturers Code (FMCX and paragraph reference. 24. Inspection and Test Equipment. Tal 23 is a list of the inspection and test equipmen, used to determine conformance to specifications and requirements contained in this DMWR. Items are listed by nomenclature, part numbeFMC, and figure reference.
2-6. Bulk and Expendable Materials.
Table 2-4 contains a listing of bulk and expendable materials requirements for use in this DMWR Expendable materials are those which may be consumed in use or that lose their identity in an assembly.
Section
2-6. Repair Parta. Repair and
II.
STANDARDS
2-9. Modification Requirements. Applicable modification work orders required to update the aircraft to the latest configuration are listed in table 2-5.
replacement
parts and kits are required for overhaul, modification and repair are found in TM 551520-214 23P. 2-7. Modification Criteria. Aircraft shall be modified to the latest configuration unless otherwise directed. All modification work orders (MWQ) will be complied with as specified in the contract documents or PWDs. Aircraft shall be identified with a modification data plate as pre .. - scribed in Chapter 1, Section II paragraph 18.
Kits and Parts Required. Kits and parts required to accomplish modification are listed in appropriate modification work orders (MWO) and TM 55152@214~23P. 2-8.
2-10. Depot Maintenance Mobilization. In the event of mobilization, all depot maintenance overhaul/repair procedure requirements, except those necessary to return the end item, assembly, subassembly or component to a serviceable condition, are to be exempt or revised. The exemptions/revisions are identified in appendix A. This appendix shall be provided by the procuring activity maintenance engineering group.
2-2
Change 1
lhhl~
2. I.
Typical
Utility
and
Space
Hcqnircruenta.
A.REA
AREA REQUIRED PER AIRCRAFT (SQ. ET.) 9.0 7.5 15.0 80.0 5.0 80.0 100.0 42.5
PROCESS STEAM
COMPRESSED AIR
WATER
EXHAUST VENTILATION
ENVIKONMENTAL CONTROL
Quick Change Assembly Small Parts Repair mmponent Assembly Electrical and Instruments Aircraft Paint Shop Paint Shop
X X X X X X X X Temp. & Humidity Control X X Humidity Control Humidity Control X X Humidity Control X
FIight & Ground Check Component Overhaul and Maintenance Structures Avionics
70.0 25.3
125 125
PSA & Disassembly Rotor Wing Tail Boom & Surface Rubber, Glass and Plastics Plating Shop
5.0
100
185
MWR
56-1620-214
Table 2-2. Special Tools List. I
PART
NUMBER
FMC 02731
REFERENCE
369A2000-50003
Fuselage Holding Fixture and Holding Plate Aircraft Stand Tailboom Fixture Support
369A9955 SM5E531
3 4 5 6
Alignment Fixture Engine and Tailboom Wrench Holding Adapter and Block Set
NO.
REFERENCE
Materials.
Item No.
Nomenclature Cleaning Compound Alkaline Waterbase Barrier Material, Grease Roof Paint Remover Methyl-Ethyl-Ketone Scotchbrite &pe A Paint Remover (Use for Epoxy Primer) Acid Acetic Glacial Acid Chromic Potassium Bichromate Trichloroethylene Alkaline Cleaner Oakite NST Abrasive Pads Nylon Web (Very Fine) Aluminum Oxide Cloth, 400 Grit Abrasive Glass Beads, Size 10 Chemical Film Magnesium Alloy, Process for Retreatment and Prevention of Corrosion
188
Military Specification MILG25769 MILE121 MILR-81299 IT-M-261 B LP-50 MILR-8 1294 O-A-760 O-G-303 o-P-559 0T634B FSCM 44%9 27713 or 76381 10646 MILG99S4 A MILGS54 1 MILM-3171 C
::
3 4 5 6 7 8 9 10 11 I2 13
I4 I r> 16
24