Documente Academic
Documente Profesional
Documente Cultură
J5 Header Pinout P2.7 P2.5 P2.3 P2.1 VCC P2.6 P2.6 P2.4 P2.4 P2.2 P2.2 P2.0 P2.0 P3.7 P3.5 P3.3 P3.1
J6 Header Pinout P3.6 P3.6 P3.4 P3.4 P3.2 P3.2 P3.0 P3.0 GND PORT 3
DTDT-51
GND VCC
2 1
PORT 2 *
If UART RS-232 lines in this module are used, P3.1 and P3.0 wont be connected to this header as digital I/O J7 Header Pinout (SCK) P1.7 (MISO) P2.5 RST NC (MOSI P1.5
Hardware Specification
1. 2. 3. 4. 5. 6. 7. 8. AT89S51 Microcontroller with 4 KB Flash Memory. Supports variant of 40-pins MCS-51 , such as: AT89S51, AT89S52, AT89S53, AT89S8252, AT89LS53, and AT89LS8252. Up to 32 pins programmable I/O lines. RC reset circuit, reset button, and brown-out detector. 11,0592 MHz oscillator frequency. Enhanced UART RS-232 serial communication lines with RJ11 connector. ISP programming port. Power supply input voltage 9-12 VDC (VIN) and output voltage 5 VDC (VOUT).
2 1
GND VCC NC NC GND
ISP Header
To use UART RS-232 serial communication in the module, configure J8 and J9 as follows: J8 and J9 Configuration TX J9 J8 P3.1 J9 J8
RX Jumper configuration when P3.0 and P3.1 are used for UART RS-232 serial communication lines
P3.0 Jumper configuration when P3.0 and P3.1 are used for digital I/O or UART TTL serial communication lines
DT-51 DT-51 Low Cost Micro System ver 2.0 J2 RX (pin 5) TX (pin 4) GND (pin 3)
2 1
J1 Front View 5 4 3 2 RX TX GND
GND VCC
PORT 0
PORT 1
Basic Compiler for MCS-51 : BASCOM-8051 Demo Version. ASM51 Assembler. Atmel Microcontroller ISP Software. LCmicro.ASM, LCmicroS.ASM, LCmicro2.ASM sample programs. SERTEST.EXE Tester Program. Datasheets of several MCS-51 Microcontrollers supported by DT-51 Low Cost Micro System.
2 1
2 1
7. 8.
DT-51 Low Cost Micro System ver 2.0 Manual. Innovative Electronics Offline Website.
text "Success! will appear. If serial communication is failed, the text Fail will be displayed and a window containing text Fail! will appear. The square waves on Port 0, Port 1, Port 2, and Port 3 can be examined by oscilloscope or by connecting the ports to LED circuitry or to DT-I/O LED Logic Tester to see the blinking LED lights.
Testing Procedure A program that has been written down into AT89S51 (LCmicro2.ASM) can be used for preliminary testing. This program will generate square waves through all Port 0, Port 1, Port 2, and Port 3 I/O pins, except P3.0 and P3.1 because they are used as UART communication lines. Testing steps: 1. Configure J8 and J9 for UART RS-232 communication, and then apply power supply input voltage to Low Cost Micro System. 2. Connect DB-9 Connector on computer and RJ11 on Low Cost Micro System using the provided serial cable. 3. Run SERTEST.EXE program. Determine COM Port to be used and press Start If serial communication is successful, Start. information about the sent and received data (0 = 0, 1 = 1, 2 = 2, etc) will be displayed, and a window containing
E-mail: support@innovativeelectronics.com
Trademark & Copyright - DT-51 is a trademark of Innovative Electronics - MCS-51 is a registered trademark of Intel Corporation - BASCOM-8051 is copyright by MCS Electronics - ASM51 is copyright by MetaLink Corporation - Atmel Microcontroller ISP Software is copyright by Atmel Corporation