Documente Academic
Documente Profesional
Documente Cultură
List of selected paper for SPICON 2012 NOTE : For any query about your selected paper contact us on spicon2012mech@spce.ac.in on or before 24/05/2012 upto 2 pm only. Any query will not be entertained after 2 pm. Paper code is for official purpose only, please check the paper title & authors name.
Index
Sr. No. Paper Code Paper Title Authors Name
A-004
A-008
1) Ashok A. Dhale 2) Dr. G. K. Awari 3) Dr. M. P. Singh 1) Bhusnoor S.S. 2) Kasookar I.S. 3) Pandey A.A. 4) Pradhan B.M. 1) Mrs. V. S. kumbhar 2) Mrs. M. S. Vedpathak 3)Mrs. K. H. Dhanawade
A-010
A-013
D-001
D-004
D-006
D-007
1) Prof. P. Vasudevan
D-009
5) Madhuri Kamble
10
D-012
11
D-013
12
D-021
13
D-022
Prediction of Tensile Strength Of Single Wall Carbon Nanotubes Using MATLAB & ANSYS Softwares
14
D-023
1) V.M.Bhojawala
15
F-002
16
F-003
17
F-007
Numerical Investigation Of Flow Behavior Across Orifice Plate: Effect Of Bevel Angle
18
F-008
1) Bhaumik 2) Dr.R.S.Maurya
19
F-009
1) Manikandapirapu P.K. 2) Srinivasa G.R. 3) Sudhakar K.G. 4) Madhu D. 1) Manikandapirapu P.K. 2) Srinivasa G.R. 3) Sudhakar K.G. 4) Madhu D 1) Kaustubh Potnis 2) Bhushan Naik 3) Vedant Chavan 4) Dr.Prof.A.V.Bhonsale 1) Pramod Kumar 2) Prudhvi kumar 3) Meenakshi Jain 4) Gagandeep Singh
20
F-010
21
F-011
22
M-001
23
M-003
Synthesis and Characterization of Few Layer Graphene via Cold Wall CVD Route
1) Mohammad Faisal
24
M-004
25
M-005
26
P-004
27
P-005
Experimental Investigation And Optimization Of The Process Parameters Of Lapping Operation By Taguchi Approach For Material Removal Rate Of Cast Iron
1) Pravin R. Parate
28
P-008
29
P-009
30
P-011
Optimized Design of Injection Mould for Case Upper-R.H Based on CAE Technology
31
P-012
32
P-013
33
P-020
1) C. M. Choudhari Modeling And Simulation Of Solidification In Metal 2) K. J. Padalkar Casting For Defects Minimization 3) K. K. Dhumal
34
P-022
35
P-023
Developing a Standard Quality Procedure and Performance of Industrial fan as per IS 4894
1) Chetan Somani
36
P-024
37
P-025
38
P-026
39
S-005
Performance Analysis Of Manufacturing System And Its Mapping For Optimisation Of Resources
40
S-007
Importance of Remanufacturing Sector as a Secondary Market in India in view of Optimum Profit Life Cycle
41
S-008
42
S-010
1) Dr. D. N. Raut 2) Rajesh Onkarrao Bhagwat 1) S.S.Pawar 2) V.K. Sunnapwar 3) Sarvesh Satam 4) Vinit Rawool 5) Vipul Kumar
43
T-003
44
T-005
1) Kaustubh A. Chatorikar
45
T-006
Thermal Losses In External Central Receiver With Air As Heat Transfer Fluid
46
T-011
1) Shivangi Ruparel 2) Sangita bansode 3) Paresh Tulankar 1) Y.P.Bhalerao 2) Amey S. Wagh 3) S.J. Kulkarni 4) S.V. patil
47
T-013
48
T-017
Modeling Condensing Heat Exchanger For Efficiency Improvement Of Thermal Power Plants
49
T-018
50
T-020
Solar Refrigeration
51
T-021
Effect Of Length Variation Between Condenser And 1) Bysani Malakondaiah Evaporator Units On The Performance Of Split A/C 2) Dr A.V. Bhonsale
52
T-022
Heat & Fluid Flow Analysis In A Seven Segment Thermal Plasma Torch
53
T-024
Fabrication and Analysis of Two Hybrid Systems of Solar Cell Using Thermoelectric Module as Cooler As Well As Generator
54
T-025
55
T-026
56
T-027
Performace Analysis of Earth Air Tonnel System For Hot and Humid Climate