Documente Academic
Documente Profesional
Documente Cultură
Global standard low-IF demodulator and PCI audio and video decoder for analog TV
Rev. 03 19 May 2008 Product data sheet
1. General description
The SAA7131E combines a digital global standard low-IF demodulator for analog TV with a PCI audio and video decoder. The IF demodulator is an alignment-free digital multistandard vision and sound low-IF signal PLL demodulator for positive and negative video modulation. It can be used worldwide for M/N, B/G/H, I, D/K and L/L standards. The IF demodulator is especially suited for the application with the TV Silicon Tuner TDA18271, TDA8275A or equivalent IC. The PCI audio and video broadcast decoder is a highly integrated, low-cost and solid foundation for TV capture in the PC, for analog TV and digital video broadcast (DTV and DVB). The various multimedia data types are transported over the PCI-bus by bus master-write, to best exploit the streaming capabilities of a modern host based system; see Figure 1.
I 2 C-bus
RF input (antenna/ cable) SILICON TUNER DIGITAL CHANNEL DECODER VSB QAM (1) QFDM
TDA18271 TDA8275A
DTV DVB
I 2 C-BUS EEPROM
(1)
low IF signal
control signals
TS PS
ENCODER: MPEG2
ITU656
SAA7131E
PCI-bus
001aab084
(1) Alternative.
Fig 1.
Application diagram for capturing live TV video and audio streams in the PC
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
2. Features
2.1 Generic properties
I I I I I I Package: LBGA256 Power supply: 3.3 V/1.8 V Power consumption of typical application: 1.35 W Meets requirements of PC Design Guides 98/99 and 2001 Is compliant with PCI Specication 2.2 and Advanced Conguration PCI-bus Power Management Interface Specication, rev. 1.1, compliant (supported states: D0, D1, D2 and D3-hot) I Reference designs available
2 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
I I I I I I
Easy programming for I2C-bus High exibility through expert mode I2C-bus interface and I2C-bus switch Four I2C-bus addresses selectable through 2 external pins Three general purpose input/output pins Separate Standby mode.
SAA7131E_3
3 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
3. Applications
I I I I I I I I I I I I I I Desktop and portable PCs Hybrid cable, terrestrial and satellite set-top boxes PCTV Digital television Personal Video Recorders (PVR) Digital Video Recorders (DVR) DVD players and recorders VCRs PCI satellite modem PCI cable modem Video conferencing Analog and digital video editing Data broadcast receiver Media hub for home server.
SAA7131E_3
4 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
4. Ordering information
Table 1. Ordering information Package Name SAA7131E LBGA256 Description Version plastic low prole ball grid array package; 256 balls; body 17 17 1 mm SOT740-2 Type number
SAA7131E_3
5 of 66
xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x
Product data sheet Rev. 03 19 May 2008
NXP B.V. 2008. All rights reserved. SAA7131E_3
5. Block diagram
NXP Semiconductors
IF DEMODULATOR PART IF AGC AGC DETECTOR VIDEO DEMODULATION low IF 10-BIT ADC FILTERS PLL DEMODULATOR INTERCARRIER GENERATION 10-BIT DAC SIF out 10-BIT DAC CVBS out
AUDIO AND VIDEO DECODER PART LEFT1 RIGHT1 sound audio inputs LEFT2 RIGHT2 ANALOG NF/AUDIO FRONT END STEREO BUFFER DIGITAL OUTPUT CROSSBAR DIGITAL INPUT CROSSBAR 16-BIT STEREO ADC STEREO DAC AUDIO OUTPUT MUX audio stereo output I 2S-bus I 2S-bus
DSP
I 2 S-BUS
SIF
FORMAT
VIDEO SCALER
MATRIX GAMMA
CLIPPING FORMAT
PCI INTERFACE
CV0_Y CV1_Y
FIFO
DMA
PCI-bus
TS PARALLEL FORMAT TS SERIAL STATIC I/O IRQ VIDEO PORT Interrupt REGISTER UNIT
SAA7131E
I 2C-bus
SAA7131E
001aab087
6 of 66
Fig 2.
Block diagram
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
6. Pinning information
6.1 Pinning
SAA7131E
2 1 A B C D E F G H J K L M N P R T
001aaf238
4 3 5
6 7
8 9
10 11
12 13
14 15
16
Pin allocation table Symbol TESTMODE VSSA1 SCL_O GPIO26 VSSA2 VDDD2 TCKI GPIO2 IF_POS VSSD1 TMSD GPIO6 IF_NEG VSSD2 LEFT2 GPIO10 Pin 2 6 10 14 2 6 10 14 2 6 10 14 2 6 10 14 Symbol VSSA1 RST_N SDA_O GPIO27 VSSA2 TDII TRSTI_N GPIO3 VDDA2 VSSD1 TCKD GPIO7 VDDA2 VSSD2 RIGHT1 GPIO11 Pin 3 7 11 15 3 7 11 15 3 7 11 15 3 7 11 15 Symbol XTALII IF_AGC SCLI GPIO0 VDDA1 TDOI SDAI GPIO4 VDDD2 TDID TRSTD_N GPIO8 VDDA1 VSSA3 LEFT1 GPIO12 Pin 4 8 12 16 4 8 12 16 4 8 12 16 4 8 12 16 Symbol XTALOI V_SYNC GPIO25 GPIO1 VDDD2 TMSI SCLD GPIO5 VDDD1 TDOD SDAD GPIO9 VSSD1 RIGHT2 VSSA3 GPIO13
NXP B.V. 2008. All rights reserved.
7 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Table 2. Pin Row E 1 5 9 13 Row F 1 5 9 13 Row G 1 5 9 13 Row H 1 5 9 13 Row J 1 5 9 13 Row K 1 5 9 13 Row L 1 5 9 13 Row M 1 5 9 13
Pin allocation table continued Symbol VSSA2 VSSD1 VREF2 GPIO14 VSSA2 VDDA1 VDDA3 GPIO18 V_IOUTP SADDR[1] VDDD3 VDDD3 VSSA2 VSSA3 VSSD3 VSSD3 S_IOUTP VSSA3 VSSD3 VSSD3 SIF VSSA3 VSSD3 VSSD3 VSSA3 VSSA3 VSSD3 VSSD3 CV2_C VSSA3 VSSD3 VSSD3 Pin 2 6 10 14 2 6 10 14 2 6 10 14 2 6 10 14 2 6 10 14 2 6 10 14 2 6 10 14 2 6 10 14 Symbol VSSA2 VDDD1 VREF1 GPIO15 RSET VREF3 VDDA3 GPIO19 V_IOUTN OUT_LEFT VDDD3 V_CLK VSSA2 OUT_RIGHT VSSD3 VDDD3 S_IOUTN VDDA3 VSSD3 VDDD3 VREF4 VSSA3 VSSD3 VDDD3 VSSA3 VSSA3 VSSD3 AD[2] CV4 VSSA3 VSSD3 AD[5] Pin 3 7 11 15 3 7 11 15 3 7 11 15 3 7 11 15 3 7 11 15 3 7 11 15 3 7 11 15 3 7 11 15 Symbol VSSD1 VSSA3 VREF0 GPIO16 VDDA2 VSSA3 VDDA3 GPIO20 VDDA2 VDDA3 VDDD3 GPIO22 VDDA2 VDDA3 VSSD3 VDDD3 VDDA2 VDDA3 VSSD3 XTALID VSSA3 VDDA3 VSSD3 VDDD3 VSSA3 VDDA3 VSSD3 AD[1] VSSA3 VDDA3 VSSD3 AD[4] Pin 4 8 12 16 4 8 12 16 4 8 12 16 4 8 12 16 4 8 12 16 4 8 12 16 4 8 12 16 4 8 12 16 Symbol VSSD1 VREF2A VSSA3 GPIO17 VDDA1 VDDA3 VSSA3 GPIO21 SADDR[0] VDDA3 VDDD3 GPIO23 PROP_RST_N VSSA3 VSSD3 VSSD3 AOUT VSSA3 VSSD3 XTALOD VSSA3 VSSA3 VSSD3 VSSD3 VSSA3 VSSA3 VSSD3 AD[0] VSSA3 VSSD3 VSSD3 AD[3]
SAA7131E_3
8 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Pin allocation table continued Symbol CV3_C PCI_RST# VDDD3 VDDD3 VSSA3 AD[29] AD[19] PAR CV1_Y AD[28] AD[18] C/BE[1]# DRCV_Y AD[27] AD[17] AD[15] Pin 2 6 10 14 2 6 10 14 2 6 10 14 2 6 10 14 Symbol DRCV_C GNT# VDDD3 C/BE[0]# VSSA3 AD[26] AD[16] AD[14] CV0_Y AD[25] C/BE[2]# AD[13] VSSA3 AD[24] FRAME# AD[12] Pin 3 7 11 15 3 7 11 15 3 7 11 15 3 7 11 15 Symbol VSSA3 VDDD3 VDDD3 AD[7] VSSA3 C/BE[3]# IRDY# PCI_CLK VSSA3 IDSEL TRDY# AD[11] VSSA3 AD[23] DEVSEL# AD[10] Pin 4 8 12 16 4 8 12 16 4 8 12 16 4 8 12 16 Symbol INT_A VDDD3 VDDD3 AD[6] REQ# AD[22] STOP# AD[9] AD[31] AD[21] PERR# AD[8] AD[30] AD[20] SERR# i.c.[1]
Pin category Power supply pins JTAG test interface pins (for boundary scan test) Digital control pins I2C-bus slave interface pins PCI interface pins Analog interface pins Crystal oscillator pins Pins for test purposes
GPIO pins and functions, audio and video decoder part Table 9
SAA7131E_3
9 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Power supply pins Type[1] AG AS AG AS Description analog ground 1, for integrated analog signal processing analog supply voltage 1 (1.8 V), for integrated analog signal processing of IF demodulator part analog ground 2, for integrated analog signal processing analog supply voltage 2 (3.3 V), for integrated analog signal processing of IF demodulator part analog ground 3, for integrated analog signal processing A2 and A5 B3, D3, F4 and F5 B1, B2, E1, E2, F1, H1 and H2 C2, D2, F3, G3, H3 and J3
Symbol Pin
AG D7, D12, E7, E12, F7, F12, H5, H8, J5, J8, K3 to K6, K8, L1 to L6, L8, M3 to M6, N3, P1 to P3, R3, T2 and T3 F8 to F11, G7, G8, H7, J6, J7, K7, L7 and M7 C5, C6, D4 and E3 to E5 C4 and E6 D5 and D6 B4, B5 and C3 H9 to H13, H16, J9 to J13, K9 to K13, K16, L9 to L13 and M8 to M13 AS VG VS VG VS VG
analog supply voltage 3 (3.3 V), for integrated analog signal processing of audio-video decoder part digital ground 1, for digital circuit, core and I/Os digital supply voltage 1 (1.8 V), for digital circuits, core and I/Os of IF demodulator part digital ground 2, for digital circuits, core and I/Os digital supply voltage 2 (3.3 V), for digital circuits, core and I/Os of IF demodulator part digital ground 3, for digital circuit, core and I/Os digital supply voltage 3 (3.3 V), for digital circuits, core and I/Os of audio and video decoder part
[1]
JTAG test interface pins (for boundary scan test) Pin C7 C8 C9 C10 C11 B6 B7 B8 B9 B10 Type[1] I O I I I I O I I I Description test serial data input: tie HIGH or let oat for normal operation test serial data output: 3-state test mode select input: tie HIGH or let oat for normal operation test clock input: drive LOW for normal operation test reset input: drive LOW for normal operation test serial data input: tie HIGH or let oat for normal operation test serial data output: 3-state test mode select input: tie HIGH or let oat for normal operation test clock input: drive LOW for normal operation test reset input: drive LOW for normal operation
SAA7131E_3
10 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Table 6. Symbol
Digital control pins Pin A6 A7 A8 A9 A10 Type[1] I OD2 O IO2 IO2 Description asynchronous reset for IF demodulator IF AGC output to control tuner AGC (RC lter needed) vertical synchronization pulse to TDA18271 for TDA18271 control; equivalent to SCL; can be set to 3-state by software for TDA18271 control; equivalent to SDA; can be set to 3-state by software
I2C-bus slave interface Pin B12 C12 H4 Type[1] IO2 IO2 GO Description serial clock input (slave mode) or output (multi-master mode) serial data input and output; always available propagate reset and D3-hot output; to peripheral board circuitry (active LOW) serial clock input (slave mode) serial data input and output serial data input and output
PROP_RST_N
A11 B11
IO2 IO2
G5 and G4 IO2
PCI interface pins Pin Type[1] Description PIO and multiplexed address and data input or output: bidirectional, 3-state L14 to L16, M14 to M16, TS N15 and N16, P5 and P6, P8 to P10, P14, P16, R4 to R6, R8 and R9, R14 to R16, T4 to T9, T13 to T15[2] N4 N5 N6 P4 P7, R10, R13 and N14 PO and OD PI PI PO interrupt A output: this pin is an open-drain interrupt output, conditions assigned by the interrupt register PCI reset input: will 3-state all PCI pins (active LOW) PCI grant input: the SAA7131E is granted to master access PCI-bus (active LOW) PCI request output: the SAA7131E requests master access to PCI-bus (active LOW)
PIO and command code input or output: indicates type of requested TS transaction and byte enable, for byte aligned transactions (active LOW) PIO and initiator ready input or output: driven by the initiator, to indicate STS readiness to continue transaction (active LOW) PIO and stop input or output: target is requesting the master to stop the STS current transaction (active LOW) PIO and parity input or output: driven by the data source, even parity over TS all pins AD and C/BE[3:0]#
NXP B.V. 2008. All rights reserved.
11 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
PCI interface pins continued Pin P15 R7 R11 R12 T10 Type[1] PI PI Description PCI clock input: reference for all bus transactions, up to 33.33 MHz initialization device select input: this input is used to select the SAA7131E during conguration read and write transactions
PIO and target ready input or output: driven by the addressed target, to STS indicate readiness for requested transaction (active LOW) PIO and parity error input or output: the receiving device detects data parity STS error (active LOW) PIO and frame input or output: driven by the current bus master (owner), to STS indicate the beginning and duration of a bus transaction (active LOW) PIO and device select input or output: driven by the target device, to STS acknowledge address decoding (active LOW) PO and OD system error output: reports address parity error (active LOW)
DEVSEL# SERR#
T11 T12
[1] [2]
The pin types are dened in Table 13. See Table 2 for details.
Table 9. Symbol
GPIO pins and functions, audio and video decoder part [1] Pin Type[2] Function Audio and video port outputs TS and PS capture outputs TS_LOCK (channel decoder locked) TS_S_D (bit-serial data) TS_CLK (< 33 MHz) TS_SOP (packet start) Raw DTV/DVB outputs ADC_C[0] (LSB) X_CLK_IN GPIO R/W R/W R/W R/W and INT R/W and INT R/W R/W R/W R/W and INT
GPIO17
E16
GIO
ADC_Y[0] (LSB)
R/W
GPIO16
E15
GIO
SAA7131E_3
12 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Table 9. Symbol
GPIO pins and functions, audio and video decoder part continued[1] Pin Type[2] Function Audio and video port outputs TS and PS capture outputs Raw DTV/DVB outputs ADC_Y[8:1] GPIO R/W
GPIO15 to GPIO8
E14, E13, D16, D15, D14, D13, C16 and C15 C14, C13, B16, B15, B14, B13, A16 and A15 G14
GIO
VP[7:0] for formats: ITU-R BT.656, VMI, VIP (1.1, 2.0), etc.
GPIO7 to GPIO0
GIO
ADC_C[8:1]
R/W
V_CLK
[1]
GO
ADC_CLK (out)
The SAA7131E offers a peripheral interface with General Purpose Input/Output (GPIO) pins. Dedicated functions can be selected: a) Digital video port (VP[7:0]): output only; in 8-bit and 16-bit formats, such as VMI, DMSD (ITU-R BT.601); zoom-video, with discrete sync signals; ITU-R BT.656; VIP (1.1 and 2.0), with sync encoded in SAV and EAV codes. b) Transport Stream (TS) capture input: from the peripheral DTV/DVB channel decoder; synchronized by Start Of Packet (SOP); in byte-parallel or bit-serial protocol. c) Digitized raw DTV/DVB samples stream output: from internal ADCs; to feed the peripheral DTV/DVB channel decoder. d) Program Stream (PS) capture input, e.g. from an external MPEG encoder chip. e) GPIO: as default (no other function selected); static (no clock); read and write from or to individually selectable pins; latching strap information at system reset time. f) Peripheral interrupt (INT) input: enabled by interrupt enable register; routed to PCI interrupt (pin INT_A). The pin types are dened in Table 13.
[2]
Table 10. Symbol CV0_Y CV1_Y CV2_C CV3_C CV4 DRCV_Y DRCV_C LEFT2 LEFT1 RIGHT1 RIGHT2 VREF0 VREF1
Analog interface pins Pin R2 R1 M1 N1 M2 T1 N2 D9 D11 D10 D8 E11 E10 Type[1] AI AI AI AI AI AR AR AI AI AI AI AR AR Description composite video input (mode 0) or Y input (modes 6 and 8)[2] composite video input (mode 1) or Y input (modes 7 and 9)[2] composite video input (mode 2) or C input (modes 6 and 8)[2] composite video input (mode 3) or C input (modes 7 and 9)[2] composite video input (mode 4)[2] differential reference connection (for CV0 and CV1); to be supported with a capacitor of 47 nF connected to VSSA differential reference connection (for CV2, CV3 and CV4); to be supported with a capacitor of 47 nF connected to VSSA analog audio stereo left 2 input or mono input analog audio stereo left 1 input or mono input; default analog pass-through to pin OUT_LEFT after reset analog audio stereo right 1 input or mono input; default analog pass-through to pin OUT_RIGHT after reset analog audio stereo right 2 input or mono input analog reference ground for audio sigma-delta ADC; to be connected VSSA analog reference voltage for audio sigma-delta ADC; to be connected to VDDA and through a 220 nF capacitor connected to pin VREF0
Audio and video decoder; the related analog supply pins are included
SAA7131E_3
13 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Analog interface pins continued Pin E9 E8 F6 K2 H6 G6 K1 Type[1] AR AR AR AR AO AO AI Description analog reference voltage for audio sigma-delta ADC; to be supported with two parallel capacitors of 47 F and 0.1 F connected to VSSA; connect pin E8 with pin E9 analog reference voltage for audio FIR-DAC and SCART audio input buffer; to be supported with two parallel capacitors of 47 F and 0.1 F connected to VSSA analog reference voltage; to be supported with a capacitor of 220 nF connected to VSSA analog audio stereo right channel output; 1 V (RMS) line-out; coupling capacitor of 2.2 F analog audio stereo left channel output; 1 V (RMS) line-out, coupling capacitor of 2.2 F sound IF input from TV tuner (4.5 MHz to 9.2 MHz); coupling capacitor of 47 pF[3]
OUT_RIGHT OUT_LEFT SIF ADC IF_POS IF_NEG DAC V_IOUTP V_IOUTN S_IOUTP S_IOUTN RSET
[1] [2] [3]
IF demodulator C1 D1 G1 G2 J1 J2 F2 AI AI AO AO AO AO AR positive analog input for internal IF ADC negative analog input for internal IF ADC positive analog current output of the video output negative analog current output of the video output positive analog current output of the SSIF audio output negative analog current output of the SSIF audio output external bias setting of the DACs
The pin types are dened in Table 13. To operate in Silicon Tuner mode the video DAC output signal V_IOUT of the IF demodulator part must be looped back to one of the composite video inputs. To operate in Silicon Tuner mode the sound DAC output signal S_IOUT of the IF demodulator part must be looped back to the SIF input.
Crystal oscillator pins Pin J15 J16 A3 A4 Type[1] CI CO CI CO Description quartz oscillator input or input for external clock signal quartz oscillator output quartz oscillator input or input for external clock signal from TDA18271 quartz oscillator output
IF demodulator
Pins for test purposes [1] Pin A1 J4 Type I AO Description test mode pin; connect to digital ground analog video output for test and debug purposes
TESTMODE AOUT
[1]
SAA7131E_3
14 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Pin type description Description analog ground analog input; video, audio and sound analog output analog reference support pin analog supply voltage CMOS input; 3.3 V signal level (not 5 V tolerant) CMOS output; 3.3 V signal level (not 5 V tolerant) digital input (GPIO); 3.3 V signal level (5 V tolerant) digital input/output (GPIO); 3.3 V signal level (5 V tolerant) digital output (GPIO); 3.3 V signal level (5 V tolerant) digital input; 3.3 V signal level digital input and output of the I2C-bus interface; 3.3 V and 5 V compatible; auto-adapting digital output; 3.3 V level open-drain output; multiple clients can drive LOW at the same time (wired OR) open-drain output; for bitstream DAC with external lter circuit input according to PCI requirements input and output according to PCI requirements output according to PCI requirements sustained 3-state (for certain PCI pins); previous owner drives HIGH for one clock cycle before leaving to 3-state 3-state I/O according to PCI requirements; bidirectional ground for digital supply supply voltage
7. Functional description
7.1 General description
The SAA7131E combines the demodulation functionality of the specic low-IF with audio and video decoding functionality; see Figure 4. The low-IF is delivered from a Silicon Tuner, such as the TDA18271. The SAA7131E is functionally compatible with the SAA7135 audio and video broadcast decoder device and the stand-alone low-IF device TDA8295.
SAA7131E_3
15 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
IF AGC
BITSTREAM DAC
H/V SYNC
VIDEO DAC
analog CVBS
UPSAMPLER
low IF signal
IF ADC
FILTERS
PLL DEMOD
NYQUIST SLOPE
SWITCH
UPSAMPLER
SOUND DAC
analog SSIF
I 2 C-BUS
I 2 C-bus
001aaa273
Fig 4.
SAA7131E_3
16 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
7.2.6 IF AGC
The IF AGC detector is a gated one with a very robust and well proven H/V sync PLL block. Gating occurs on the black level (most of the time on the back porch) of the video signal and the control is delivered to the Silicon Tuner through a bitstream DAC (PWM signal at 13.5 MHz) and an external and uncritical rst-order RC low-pass lter. The correlated or small-band AGC loop, closed through the continuous IF AGC amplier in the TDA18271, is of rst-order integral action and settles at a constant IF ADC input level with a permanent headroom of 6 dB to 9 dB, depending on the standard chosen. This headroom is needed for the sound carriers and the leaking neighbor (N 1) spectrum, more than sufcient even under strong video overmodulation.
SAA7131E_3
17 of 66
xxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx x xxxxxxxxxxxxxx xxxxxxxxxx xxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxx xxxxxxxxxxxxxx xxxxxx xx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxx xxxxx x x
Product data sheet Rev. 03 19 May 2008
NXP B.V. 2008. All rights reserved. SAA7131E_3
NXP Semiconductors
GPIO
I 2C-bus
stereo output
IF sound input
INPUT SELECTION CLAMP AND GAIN CONTROL 9-BIT ADC 9-BIT ADC
I 2C-BUS INTERFACE
I 2S-BUS OUTPUT
SIF ADC
SIF DEMOD
FLC
VIDEO SCALER MATRIX 3-D GAMMA RAW VBI FORMAT PROGRAM PROGRAM SET SET VIDEO FIFOS DMA CONTROL AUDIO FIFOS DMA CONTROL BOUNDARY SCAN TEST
BTSC
SAA7131E
EIAJ NICAM FM A2
OSCILLATOR
PCI-BUS INTERFACE
SAA7131E
coa019
PCI-bus
test
xtal
18 of 66
Fig 5.
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
The SAA7131E is able to capture TV signals over the PCI-bus in personal computers; see Figure 5. The SAA7131E incorporates two 9-bit video ADCs and the entire decoding circuitry of any analog TV signal: NTSC, PAL and SECAM, including non-standard signals, such as playback from a VCR. The adaptive multi-line comb lter provides superb picture quality, component separation, sharpness and high bandwidth. The video stream can be cropped and scaled to the needs of the application. Downscaling and upscaling is supported in the horizontal and vertical direction, and an adaptive lter algorithm prevents aliasing artifacts. With the acquisition unit of the scaler two different tasks can be dened, e.g. to capture video to the CPU for compression, and write video to the screen from the same video source but with different resolution, color format and frame rate. The SAA7131E contains TV sound stereo decoding from Sound IF (SIF), for all known sound standards and also non-standard signals. Baseband stereo audio sampling is also implemented, e.g. for capturing from a camcorder or other external devices. The audio sampling rate can be locked to the video frame rate to ensure synchronization (lip sync) between the video and audio data ow, e.g. for storage, compression or time shift viewing applications. The SAA7131E incorporates analog audio pass-through and support for the analog audio loopback cable to the sound card function. The decoded video streams are fed to the PCI-bus, and are also applied to a peripheral streaming interface, in ITU, VIP or VMI format. A possible application extension is on-board hardware MPEG compression, or other feature processing. The compressed data as PS or TS is fed back through the peripheral interface, in parallel or serial format, to be captured by the system memory through the PCI-bus. The Transport Stream (TS) from a DTV/DVB channel decoder can be captured through the peripheral interface in the same way. Audio, video and transport streams are collected in a congurable FIFO with a total capacity of 1 kB. The DMA controller monitors the FIFO lling degree and writes the audio and video streams to the associated DMA channels. The virtual memory address space (from OS) is translated into physical (bus) addresses by the on-chip hardware Memory Management Unit (MMU). The application of the SAA7131E is supported by reference designs and a set of drivers for the Windows operating system (Windows driver model compliant).
19 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
The device vendor ID is hard coded to 1131h, which is the code for NXP as registered with PCI-SIG. The device ID is hard coded to 7133h. During power-up, initiated by a PCI reset, the SAA7131E fetches additional system information through the I2C-bus from the on-board EEPROM, to load actual board type specic codes for the system vendor ID, sub-system ID (board version) and ACPI related parameters into the conguration registers.
Table 14. Function Device vendor ID Device ID Revision ID Class code PCI conguration space registers Register address Value 00h and 01h 02h and 03h 08h 09h to 0Bh 1131h 7133h D1h 04 8000h Remark for NXP for SAA7131E for SAA7131E multimedia
Memory address space required 10h to 13h System (board) vendor ID Sub-system (board version) ID
[1] X = dont care.
XXXX XXXX XXXX XXXXb 2 kB [1] XXXX X000 0000 0000b loaded from EEPROM loaded from EEPROM
SAA7131E_3
20 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
The DMA channels share in time and space one common FIFO pool of 256 Dwords (1024 bytes) total. It is freely congurable how much FIFO capacity is associated with which DMA channel. Furthermore, a preferred minimum burst length can be programmed, i.e. the amount of data to be collected before the request for the PCI-bus is issued. This means that latency behavior per DMA channel can be tailored and optimized for a given application. In the event that the FIFO of a certain channel overows due to latency conict on the bus, graceful overow recovery is applied. The amount of data that gets lost because it could not be transmitted, is monitored (counted) and the PCI-bus address pointer is incremented accordingly. Thus new data will be written to the correct memory place after the latency conict is resolved.
Table 15. D0 Power management Description Normal operation: all functions accessible and programmable. The default setting after reset and before driver interaction (D0 un-initialized) switches most of the circuitry of the SAA7131E into the Power-down mode, effectively such as D3-hot. First step of reduced power consumption: no functional operation; program registers are not accessible, but content is maintained. Most of the circuitry of the SAA7131E is disabled with the exception of the crystal and real time clock oscillators, so that a quick recovery from D1 to D0 is possible. Second step of reduced power consumption: no functional operation; program registers are not accessible, but content is maintained. All functional circuitry of the SAA7131E is disabled, including the crystal and clock oscillators. Lowest power consumption: no functional operation. The content of the programming registers gets lost and is set to default values when returning to D0. FIFO conguration; typical example Data stream Y U V audio Data rate 13.5 MB/s 6.75 MB/s 6.75 MB/s 160 kB/s FIFO size programmable to 384 B 256 B 256 B 128 B Tolerant to latency of 28.4 s 37.9 s 37.9 s 800 s
Power state
D1
D2
D3-hot
FIFO conguration; fastidious example Data stream raw VBI active video, unscaled YUV 4:2:2 Data rate 27 MB/s FIFO size programmable to 640 B Tolerant to latency of 22.5 s
2 3 4
256 B 128 B
202.1 s 583.3 s
SAA7131E_3
21 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
The association between the virtual (logic) address space and the fragmented physical address space is dened in page tables (system les); see Figure 6. The SAA7131E incorporates hardware support (MMU) to translate virtual to physical addresses on the y, by investigating the related page table information. This hardware support reduces the demand for real time software interaction and interrupt requests, and therefore saves system resources.
real-time streams
FIFO POOL 0 0007h DMA DEFINITIONS (VIRTUAL ADDRESS SPACE) DMA ADDRESS GENERATION
page table 000h 0 000Fh 0000 1000h 0000 8000h 0000 9000h 0000 A000h 0000 D000h 0001 1000h 0001 4000h 0001 6000h 0001 E000h
007h 0 0017h
PCI TRANSFER AND CONTROL 0 001Fh 015h physical address space on PCI = allocated memory space = page table
001aag679
Fig 6.
SAA7131E_3
22 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Basic TV systems: dening frame rate, number of lines per eld, levels of
synchronization signals, level of video signals, blanking, black and white, signal bandwidth and the RF modulation scheme
Color transmission: dening color coding and modulation method Sound and stereo: dening coding for transmission.
TV signals that are broadcast usually conform fairly accurately to the standards. Transmission over the air or through a cable can distort the signal with noise, echoes, crosstalk or other disturbances. Video signals from local consumer equipment, e.g. VCR, camcorder, camera, game console, or even DVD player, often do not follow the standard specication very accurately. Playback from video tape cannot be expected to maintain correct timing, especially not during feature mode (fast forward, etc.). Table 18, Table 19 and Table 20 list some characteristics of the various TV standards. The SAA7131E decodes all color TV standards and non-standard signals as generated by video tape recorders e.g. automatic video standard detection can be applied, with preference options for certain standards, or the decoder can be forced to a dedicated standard. The SAA7131E incorporates BTSC and EIAJ stereo decoding and TV mono sound decoding on-chip. Baseband stereo audio can be fed into the device as analog signal.
Table 18. Overview of basic TV standards Standard M RF channel width Video bandwidth 1st sound carrier[1] Field rate fv Lines per frame Line frequency fh ITU clocks per line Sync (setup level)[2] Gamma correction Associated color TV standard Associated stereo TV sound system Country examples 6 4.2 4.5 59.94006 525 15.734 1716 40 (7.5) 2.2 NTSC, PAL BTSC, EIAJ, FM A2 N 6 4.2 4.5 50 625 15.625 1728 40 (7.5) 2.2 PAL BTSC B 7 5 5.5 50 625 15.625 1728 43 (0) 2.8 PAL NICAM, FM A2 part of Europe, Australia G/H 8 5 5.5 50 625 15.625 1728 43 (0) 2.8 PAL NICAM, FM A2 Spain, Malaysia, Singapore I 8 5.5 6.0 50 625 15.625 1728 43 (0) 2.8 PAL NICAM D/K 7 6 6.5 50 625 15.625 1728 43 (0) 2.8 SECAM, PAL NICAM, FM A2 China, Eastern Europe L 8 6 6.5 50 625 15.625 1728 43 (0) 2.8 SECAM MHz MHz MHz Hz kHz Unit
Main parameter
NICAM, AM -
[1] [2]
SAA7131E_3
23 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Table 19.
TV system color standards NTSC M 59.94 525 3.580 227.5 no PAL M 59.94 525 3.576 227.25 n.a. yes N 50 625 3.582 229.25 50 yes Middle and South America 50 625 4.434 283.75 50 yes Europe, China, Commonwealth, SECAM B, G, H, I, D L, D, G, H, K 50 625 4.406 282 4.250 272 PAL 4.4 (60 Hz) 60 525 4.434 n.a. n.a. yes Unit Hz MHz Hz -
Main parameter Field rate fv Lines per frame Chrominance subcarrier fsub fsub to fh ratio fsub offset (PAL) Alternating phase
Africa, France, Eastern transcoding Europe, Middle East VCR tapes from NTSC to PAL
Table 20.
TV stereo sound standards Analog systems Mono BTSC EIAJ FM A2 internal internal 2-Carrier Systems carrier (MPX) carrier (MPX) AM FM 2nd FM carrier mono SAP, internal FM 75[1] 15 USA, South America alternative to alternative to stereo stereo 50 15 Japan 50 to 75 15 part of Europe, Korea Digital coding NICAM 2-Carrier Systems DQPSK on 2nd carrier mono on 1st carrier 50 to 75 15 part of Europe, China s kHz Unit
Main parameter Stereo coding scheme 2nd language De-emphasis Audio bandwidth
75 15
[1]
SAA7131E_3
24 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Composite video signal (CVBS), from looped back video-DAC output of the IF
demodulator core
Composite video signals (CVBS), from conventional tuner or external source S-video signals (pairs of Y-C), e.g. from camcorder DTV/DVB low-IF signal, from an appropriate DTV or combi-tuner.
Analog anti-alias lters are integrated on-chip and therefore, no external lters are required. The device also contains automatic clamp and gain control for the video input signals, to ensure optimum utilization of the ADC conversion range. The nominal video signal amplitude is 1 V (p-p) and the gain control can adapt deviating signal levels in the range of +3 dB to 6 dB. The video inputs are digitized by two ADCs of 9-bit resolution, with a sampling rate of nominal 27 MHz (the line-locked clock) for analog video signals.
SAA7131E_3
25 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Adaptive to transitions in the picture content Adaptive to non-standard signals (e.g. VCR).
The integrated digital delay lines are always exactly correct, due to the applied unique line-locked sampling scheme (LLC). Therefore the comb lter does not need to be switched off for non-standard signals and remains operating continuously.
SAA7131E_3
26 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
VBI first sample 1st field (odd, FID = 0) VBI region, raw samples
sample rate
VBI last sample VBI DMA 1st buffer (A) 2nd buffer (A)
active video area 2nd field (even, FID = 1) VBI region, raw samples video first line video region - cropped - scaled
scaling
sample rate
video DMA (A) e.g. interlaced 1st buffer (upper field) 2nd buffer (lower field)
The capture acquisition for scaling and DMA has separate programming parameters for VBI and video region and associated DMA channels.
Fig 7.
The scaling acquisition denition also includes cropping, frame rate reduction, and denes the amount of pixel and lines to be transported through DMA over the PCI-bus. Two programming pages are available to enable re-programming of the scaler in the shadow of the running processing, without holding or disturbing the ow of the video stream. Alternatively, the two programming pages can be applied to support two video destinations or applications with different scaler settings, e.g. rstly to capture video to CPU for compression (storage, video phone), and secondly to preview the picture on the monitor screen. A separate scaling region is dedicated to capture raw VBI samples, with a specic sampling rate, which is written into its own DMA channel.
SAA7131E_3
27 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
scaling
task "A"
active video area 2nd field (even, FID = 1) VBI region, raw samples
sample rate
scaling
active video area 3rd field (odd, FID = 0) VBI region, raw samples
sample rate
video DMA (B) e.g. single FID task "B" active video area 4th field (even, FID = 1) VBI region, raw samples
sample rate
1st buffer
scaling
Two video capture tasks can be processed in an alternating manner, without need to reprogram any scaling parameter or DMA denition.
Fig 8.
SAA7131E_3
28 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Closed Caption (CC) for the hearing impaired (CC, on line 21 of rst eld) Intercast data [in USA coded in North American Broadcast Text System (NABTS)
format, in Europe in World System Teletext (WST)], to transmit internet related services, optionally associated with actual video program content
Vertical Interval Time Codes (VITC) as inserted in camcorders e.g. use for video
editing
Copy Guard Management System (CGMS) codes, to indicate copy protected video
material, sometimes combined with format information [Wide Screen Signalling (WSS)]. This information is coded in the unused lines of the vertical blanking interval, between the vertical sync pulse and the active visible video picture. So-called full-eld data transmission is also possible, utilizing all video lines for data coding. The SAA7131E supports the capture of VBI data, by the denition of a VBI region, which is captured as raw VBI samples. These samples are sliced and decoded by software on the host CPU. The raw sample stream is taken directly from the ADC and is not processed or ltered by the video decoder. The sampling rate of raw VBI data can be adjusted to the needs of the data slicing software.
SAA7131E_3
29 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
+255 +235
white
+128
LUMINANCE 100 %
+128
colorless CB-COMPONENT
+128
colorless CR-COMPONENT
+44 +16 0
+16 0
b. CB output range
c. CR output range
Nominal digital levels for YUV (Y, CB and CR) in accordance with ITU-R BT.601
LUMINANCE
LUMINANCE
+60 SYNC
sync bottom
001aac244
sync bottom
001aac245
Fig 10. Nominal digital levels for CVBS and raw VBI samples
mhb999
SAA7131E_3
30 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
The SAA7131E incorporates the YUV-to-RGB matrix (optional), the RGB-to-YUV matrix and a three channel look-up table in between; see Figure 11. Under nominal settings, the RGB space will use the same number range as dened by the ITU (see Figure 9) for luminance, between 16 and 235. As graphic related applications are based on full-scale RGB, i.e. 0 to 255, the range can be stretched by applying appropriate brightness, contrast and saturation values. The look-up table supports gamma correction (freely denable), and allows other non-linear signal transformation such as black stretching. The analog TV signal applies a quite strong gamma pre-compensation (2.2 for NTSC and 2.8 for PAL). As computer monitors exhibit a gamma (around 2.5), the difference between gamma pre-compensation and actual screen gamma has to be corrected, to achieve best contrast and color impression. The SAA7131E offers a multitude of formats to write video streams over the PCI-bus: YUV and RGB color space, 15-bit, 16-bit, 24-bit and 32-bit representation in a packed or in a planar format. For legacy requirements a clipping procedure is implemented, that allows the denition of 8 overlay rectangles. This process can be used alternatively to associate alpha values with the video pixel.
Streaming real time video to a video side port at the VGA card, e.g. through ribbon
cable over the top
Feeding the video stream to a local MPEG compression device on the same PCI
board, e.g. for a time shift viewing application. The video port of the SAA7131E supports the following 8-bit and 16-bit wide YUV video signalling standards; see Table 9:
VMI: 8-bit wide data stream, clocked by LLC at 27 MHz, with discrete sync signals
HSYNC, VSYNC and VACTIVE
ITU-R BT.656, parallel: 8-bit wide data stream, clocked by LLC at 27 MHz,
synchronization coded in SAV and EAV codes
VIP 1.1 and 2.0: 8-bit or 16-bit wide data stream, clocked by LLC at 27 MHz,
synchronization coded in SAV and EAV codes (with VIP extensions)
Zoom Video (ZV): 16-bit wide pixel stream, clocked by LLC/2 at 13.5 MHz, with
discrete sync signals HSYNC and VSYNC
ITU-R BT.601 direct (DMSD): 16-bit wide pixel stream, clocked by LLC at 27 MHz,
with discrete sync signals HSYNC, VSYNC/FID and CREF
Raw DTV/DVB sample stream: 9-bit wide data, clocked with a copy of signal
X_CLK_IN. The VIP standard is designed to transport scaled video and discontinuous data stream by allowing the insertion of the value 0h as a marker for empty clock cycles. For the other video port standards, a data valid ag or gated clock can be applied.
SAA7131E_3 NXP B.V. 2008. All rights reserved.
31 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
mono
stereo[2]
mono
mono or 2 mono
stereo
Sample rate
32 kHz
32 kHz, 32 kHz, 44.1 kHz or 44.1 kHz or 48 kHz 48 kHz mono or 2 mono stereo
PCI (audio streaming) Signal mono or mono, stereo stereo or and/or SAP dual 32 kHz 32 kHz or 48 kHz mono, stereo or dual 32 kHz or 48 kHz mono, stereo or dual 32 kHz or 48 kHz mono or stereo 32 kHz or 48 kHz mono
Sample rate
32 kHz or 48 kHz
Feature processing Volume and balance Bass and treble Incredible Stereo Incredible Mono X X X if SAP X X X either or dual X X X either or dual X X X either or dual X X X X X X
[1] [2]
Simultaneous decoding of stereo and SAP. dbx-TV noise reduction either on stereo or SAP. Default pass-through of L1 and R1.
SAA7131E_3
32 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
The digital FM demodulation maintains stable phase accuracy, which results in improved channel separation, compared to traditional analog demodulation. TV sound decoding operates at a sample rate of 32 kHz, which results in an audio bandwidth of up to 15 kHz. The SAA7131E incorporates baseband stereo audio ADCs, to capture sound signals associated with external video sources, e.g. camera, camcorder or VCR. For concurrent capture of audio and video signals, it is important to maintain synchronization between the two streams. The spoken word and other sound should match the displayed picture within a video frame (130 s respectively 125 s lip-sync). The SAA7131E uses a special technique to lock the audio sampling clock to the video frame frequency through the Frame-Locked Clock (FLC), so that a programmable but constant number of audio samples is associated with each video frame. This is especially important for video editing, compression and recording, e.g. time shift viewing. There is no drift between the audio and video streams, not even for longer recording times.
Bass, treble, balance and volume control Automatic volume levelling (this algorithm lowers louder parts, e.g. commercials) Incredible Mono (this algorithm adds stereo-like sound impression to monaural audio
signals)
Incredible Stereo (this algorithm makes stereo sound impression wider: the distance
between the two loudspeakers seems to become greater)
33 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
of the inputs of the SAA7131E. By default, after a system reset and without involvement of any driver, this audio signal is passed through to the analog audio output pins that will feed the loopback cable to the sound card line-in connector. The A/V capture driver has to open the default audio pass-through and switch in the TV sound signal.
7.7.5 FM radio
In Silicon Tuner mode the SAA7131E supports FM radio reception and decoding. The SIF input must be connected to the Silicon Tuner device (TDA18271) through additional cheap external circuitry; see Application Notes SAA7131E.
SAA7131E_3
34 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
7.9.3 GPIO
The SAA7131E offers a set of General Purpose Input/Output (GPIO) pins, to interface to on-board peripheral circuits; see Table 9. These GPIOs are intended to manage dedicated functions:
Digital video port output: 8-bit or 16-bit wide (including raw DTV) Digital audio serial output: i.e. I2S-bus output Transport stream input:
parallel (also applicable for program stream and elementary stream) serial (also applicable as I2S-bus input)
Peripheral interrupt input: four GPIO pins of the SAA7131E can be enabled to raise an
interrupt on the PCI-bus. By this means, peripheral devices can directly intercept with the device driver on changed status or error conditions. Any GPIO pin that is not used for a dedicated function is available for direct read and write access through the PCI-bus. Any GPIO pin can be selected individually as input or output (masked write). By these means, very tailored interfacing to peripheral devices can be created through the SAA7131E capture driver operating on a Windows operating system. At system reset (PCI reset) all GPIO pins will be set to 3-state and input, and the logic level present on the GPIO pins at that moment will be saved into a special strap register. All GPIO pins have an internal pull-down resistor (LOW level), but can be strapped externally with a 4.7 k resistor to the supply voltage (HIGH level). The device driver can investigate the strap register for information concerning the hardware conguration of a given board.
SAA7131E_3
35 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
8. Limiting values
Table 22. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). All ground pins connected together and grounded (0 V); all supply pins connected together. Symbol VDDD1 VDDD2 VDDD3 VDDA1 VDDA2 VDDA3 VSS VI(a) VI Parameter digital supply voltage 1 digital supply voltage 2 digital supply voltage 3 analog supply voltage 1 analog supply voltage 2 analog supply voltage 3 ground supply voltage difference analog input voltage input voltage Conditions for IF demodulator for IF demodulator for decoder for IF demodulator for IF demodulator for decoder between pins VSSA and VSSD at analog inputs at pin XTALII at pins SCLI and SDAI at pins XTALID, SDAD and SCLD VI(D) digital input voltage at digital I/O stages, outputs in 3-state 0.5 V < VDDD2 < +3.0 V 3.0 V < VDDD2 < 3.6 V 0.5 V < VDDD3 < +3.0 V 3.0 V < VDDD3 < 3.6 V Tstg Tamb Vesd storage temperature ambient temperature electrostatic discharge voltage human body model machine model
[1] [2] [3]
[1] [2] [3]
Min 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 40 0 -
Unit V V V V V V mV V
VDDD1 + 0.5 V VDDD2 + 0.5 V VDDD3 + 0.5 V +4.6 +5.5 +4.6 +5.5 +150 70 2000 150 V V V V C C V V
The device has to be programmed according to the register settings described in the User Manual SAA7131E, in order not to exceed 1.55 W. Class 2 according to EIA/JESD22-114-B. Class A according to EIA/JESD22-115-A.
9. Thermal characteristics
Table 23. Symbol Rth(j-a)
[1]
Typ 35
Unit K/W
The overall Rth(j-a) value can vary depending on the board layout. To minimize the effective Rth(j-a) all power and ground pins must be connected to the power and ground layers directly. An ample copper area direct under the SAA7131E with a number of through-hole plating, which connect to the ground layer (four-layer board: second layer), can also reduce the effective Rth(j-a). Please do not use any solder-stop varnish under the chip. In addition the usage of soldering glue with a high thermal conductance after curing is recommended.
SAA7131E_3
36 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
10. Characteristics
Operating conditions for minimum and maximum values in Table 24 to Table 26: VDDD1 = 1.7 V to 1.9 V; VDDD2 = VDDD3 = 3.15 V to 3.45 V; VDDA1 = 1.7 V to 1.9 V; VDDA2 = VDDA3 = 3.15 V to 3.45 V; Tamb = 0 C to 70 C; unless otherwise specied. Operating conditions for typical values in Table 24 to Table 26: VDDD1 = 1.8 V; VDDD2 = VDDD3 = 3.3 V; VDDA1 = 1.8 V; VDDA2 = VDDA3 = 3.3 V; Tamb = 25 C; unless otherwise specied.
10.1 Supplies
Table 24. Symbol VDDD1 VDDD2 VDDD3 VDDA1 VDDA2 VDDA3 IDDD1 IDDD2 IDDD3 IDDA1 IDDA2 IDDA3 P Supply characteristics Parameter digital supply voltage 1 digital supply voltage 2 digital supply voltage 3 analog supply voltage 1 analog supply voltage 2 analog supply voltage 3 digital supply current 1 digital supply current 2 digital supply current 3 analog supply current 1 analog supply current 2 analog supply current 3 power dissipation power state (see Table 15) D0 in Silicon Tuner mode D0 in non-Silicon Tuner mode D1 D2 D3-hot D3-hot
[1] [2] [3] [4] [5] All features are enabled. CVBS operation in Silicon Tuner mode with rst video decoder analog front end; second video decoder front end is disabled through PCI-bus or I2C-bus; see User Manual SAA7131E. CVBS or Y/C operation through external sources e.g. VCR; IF demodulator is set in Standby mode through PCI-bus or I2C-bus; see User Manual SAA7131E. If pins PROP_RST_N and RST_N are connected. If IF demodulator is set in Standby mode and pins PROP_RST_N and RST_N are not connected; RST_N must be inactive; see User Manual SAA7131E.
[4] [5] [2] [3]
Conditions for IF demodulator for IF demodulator for decoder for IF demodulator for IF demodulator for decoder
[1] [1] [1] [1] [1] [1]
Min 1.7 3.15 3.15 1.7 3.15 3.15 26 210 210 1.1 240 240 1.1 1.1 -
Typ 1.8 3.3 3.3 1.8 3.3 3.3 32 225 225 1.25 247 247 1.35 1.35 0.55 0.50 -
Max 1.9 3.45 3.45 1.9 3.45 3.45 40 250 250 1.5 260 260 1.55 1.55 0.45 0.05
Unit V V V V V V mA mA mA mA mA mA W W W W W W
SAA7131E_3
37 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
10.2 IF demodulator
Table 25. Symbol IF demodulator characteristics Parameter Conditions Min Typ Max Unit
Digital pins (pins RST_N, TESTMODE, SADDR0, SADDR1, V_SYNC, SCL_O, SDA_O, TRSTI_N, TCKI, TMSI, TDOI and TDII) VIH VIL VOH VOL Ci fclk f/fclk HIGH-level input voltage LOW-level input voltage HIGH-level output voltage LOW-level output voltage input capacitance clock frequency relative frequency deviation from clock frequency external clock frequency peak-to-peak clock input voltage input capacitance crystal frequency relative crystal frequency variation with temperature relative crystal frequency variation with time crystal ambient temperature peak-to-peak input voltage differential input resistance differential input capacitance input voltage operational voltage from AGC feedback loop all standards except L/L L/L 6 9 6 9 6 9 dB dB for 0 dB see User Manual SAA7131E for PLL settings all inputs except XTALII all inputs except XTALII source current 4 mA sink current 4 mA 2 2.4 54 5.5 0.8 0.4 5 200 V V V pF MHz ppm
VDDD2 + 0.5 V
Reference frequency in slave mode (square wave signal on pin XTALII) fclk(ext) Vi(clk)(p-p) Ci fxtal fxtal(T)/fxtal fxtal(t)/fxtal Tamb(xtal) Vi(p-p) Ri(dif) Ci(dif) Vi 4 400 8 20 1.8 10 16 16 2.0 50 900 2 30 50 10 +70 2.2 2 MHz mV pF MHz ppm ppm C V k pF
SAA7131E_3
38 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
IF demodulator characteristics continued Parameter input frequency Conditions Picture Carrier (PC) M/N B G/H I D/K, L L rst Sound Carrier (SC1) M/N B G/H I D/K, L L 60 60
[1]
Min -
Typ -
Max 5.75 6.75 7.75 7.75 7.75 1.25 1.25 1.25 2.25 1.75 1.25 7.75 -
Unit MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz dB dB dB
IF selectivity sup(stpb) stop-band suppression Hilbert lter decimation lter notch lter for NSC (NPC for L), all standards Carrier recovery PLL B3dB(cl) closed-loop 3 dB bandwidth super wide wide medium small flock-in mover(PC) fstep(AFC) BT(tot) sup(stpb) lock-in frequency range picture carrier overmodulation black for L/L, at eld white else index AFC step frequency total transition bandwidth stop-band suppression 128 steps Nyquist lter, all standards Nyquist lter, all standards video low-pass lter (M/N, B/G/H, I, D/K and L/L) Bvideo(1dB) tripple(GDE) B3dB(cl) f3dB(lpf) 1 dB video bandwidth group delay equalizer ripple time closed-loop 3 dB bandwidth low-pass lter 3 dB frequency M/N B/G/H, I, D/K, L/L peak value closed-loop through IF AGC and TDA18271 IF AGC post lter
[2]
40
830 117 30
50 0.25 1.1
kHz kHz kHz kHz kHz % kHz MHz dB dB MHz MHz ns kHz kHz
IF demodulation
SAA7131E_3
39 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
IF demodulator characteristics continued Parameter peak-to-peak output voltage Conditions 75 DC load; sync-white modulation negative PC modulation (except L/L) 65 % 90 % (nominal) 115 % positive PC modulation (L/L) 65 % PC 97 % PC (nominal) 115 % 0.8 0.8 0.8 4.8 4.0 0.9 1.1 1.0 4.85 4.05 < 2.0 < 1.5 1 1.2 1.2 1.2 5 4 2 V V V MHz MHz % deg % 0.8 0.8 0.8 0.9 1.0 1.1 1.2 1.2 1.2 V V V Min Typ Max Unit
fvideo
video frequency
Gdif dif
Vstlt/VCVBS(p-p) synchronization tilt voltage to peak-to-peak CVBS voltage ratio Vftlt/VCVBS(p-p) frame tilt voltage to peak-to-peak CVBS voltage ratio Vtro/Vtro IM(blue) relative transient response overshoot voltage variation intermodulation suppression (blue) 2T pulse carrier levels related to PC sync: PC = 3.2 dB; CC = 19.2 dB; SC = 13 dB at 1.1 MHz (related to black/white in RMS, equals CC + 3.6 dB) at 3.3 MHz (related to CC) IM(yellow) intermodulation suppression (yellow) carrier levels related to PC sync: PC = 10.0 dB; CC = 19.2 dB; SC = 13 dB at 1.1 MHz (related to black/white in RMS, equals CC + 3.6 dB) at 3.3 MHz (related to CC) (S/N)w weighted signal-to-noise ratio all standards except L/L L/L
[4] [3]
1.5
63 64
67 68
dB dB
55 63 55 53
58 67 57 55
dB dB dB dB
SAA7131E_3
40 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
IF demodulator characteristics continued Parameter power supply rejection ratio Conditions fripple = 70 Hz; 100 mV (p-p); video signal: grey, level: 50 %; input level: 60 dB V (RMS) PC SAA7131E stand-alone positive video modulation, standard L, 1.8 V positive video modulation, standard L, 3.3 V negative video modulation, standard B, 1.8 V negative video modulation, standard B, 3.3 V SAA7131E together with TDA18271 positive video modulation, standard L, 1.8 V positive video modulation, standard L, 3.3 V negative video modulation, standard B, 1.8 V negative video modulation, standard B, 3.3 V 40 14 40 14 55 41 16 42 16 60 dB dB dB dB dB 55 32 55 32 58 34 58 34 dB dB dB dB Min Typ Max Unit
sup(f)L(unw)
4.8 MHz video modulation; related to black-to-white in 10 MHz to 200 MHz band 1 k DC or AC load; no modulation; PC/SC1 = 13 dB; scaled linearly for all other ratios all standards except L/L standard L/L
40 40
56 45
mV mV
SAA7131E_3
41 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
IF demodulator characteristics continued Parameter weighted audio signal-to-noise ratio Conditions FM: through SSIF sound demodulator in dual mode; CCIR468-4, FM mode related to 27 kHz deviation before pre-emphasis; 10 % residual PC 1st Sound Carrier (SC1) black picture at eld white picture 6 kHz sine wave picture 250 kHz square wave picture crosshatch picture color bar picture 2nd Sound Carrier (SC2) black picture at eld white picture 6 kHz sine wave picture 250 kHz square wave picture crosshatch picture color bar picture AM: through SSIF sound demodulator in dual mode; CCIR468-4, AM mode related to 54 % modulation degree; 3 % residual PC; 1st Sound Carrier (SC1) black picture at eld white picture color bar picture 38 36 38 41 38 41 dB dB dB 54 51 50 40 50 51 59 55 51 44 52 55 dB dB dB dB dB dB 60 55 50 50 50 59 63 58 51 53 53 62 dB dB dB dB dB dB Min Typ Max Unit
PSRR
fripple = 70 Hz; 100 mV (p-p); video signal: grey, level: 50 %; input level: 60 dB V (RMS) PC SAA7131E stand-alone FM sound, standard B, 1.8 V FM sound, standard B, 3.3 V AM sound, standard L, 1.8 V AM sound, standard L, 3.3 V SAA7131E together with TDA18271 FM sound, standard B, 1.8 V FM sound, standard B, 3.3 V AM sound, standard L, 1.8 V AM sound, standard L, 3.3 V 50 46 44 22 40 52 50 47 24 42 dB dB dB dB dB 55 45 55 45 60 49 59 49 dB dB dB dB
sup(f)L(unw)
[1] [2]
Standard dependent located at 7.25 MHz, 8.25 MHz, 9.25 MHz and 10.25 MHz. For standards B/G/H half, D/K half, I at, M (FCC) full and L/L full.
NXP B.V. 2008. All rights reserved.
SAA7131E_3
42 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
[3] [4]
Half-Amplitude Duration (HAD): 250 ns for M and 200 ns for all other standards. According to ITU-T J.61 (CCIR567).
Crystal oscillator
LOW-level input voltage at pin XTALID at pin XTALID or XTALOD see Table 27
I2C-bus interface, compatible to 3.3 V and 5 V signalling (pins SDAD and SCLD) VIH VIL VOL fbit 0.7 VDDD3 0.5 0 VDDD3 + 0.5 V
Analog video inputs Inputs (pins CV0_Y, CV1_Y, CV2_C, CV3_C and CV4) ICL Vi(p-p) Ci ct(ch) Bvideo(3dB) dif Gdif DLEDC ILEDC S/N ENOB clamping current peak-to-peak input voltage input capacitance channel crosstalk 3 dB video bandwidth differential phase differential gain DC differential linearity error DC integral linearity error signal-to-noise ratio fi = 4 MHz; anti-alias lter bypassed; AGC = 0 dB fi < 5 MHz ADC only amplier plus anti-alias lter bypassed amplier plus anti-alias lter bypassed DC input voltage VI = 0.9 V
[1]
0.375 -
8 0.75 7 2 2 1.4 2 50 8
1.07 10 50 -
SAA7131E_3
43 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Audio and video decoder characteristics continued Parameter Conditions Min Typ Max Unit
Analog sound input (pin SIF) maximum peak-to-peak input level adjustment input voltage 0 dB 10 dB Vi(min)(p-p) minimum input voltage (peak-to-peak value) input level adjustment 0 dB 10 dB Vi(AGC) fi Ri Ci Vi(nom)(rms) Vi(max)(rms) Vo(nom)(rms) Vo(max)(rms) Ri Ro RL(AC) Co(L) Voffset(DC) S/N AGC input voltage input frequency input resistance input capacitance nominal input voltage (RMS value) maximum input voltage THD < 3 % (RMS value) nominal output voltage (RMS value) maximum output voltage (RMS value) input resistance output resistance AC load resistance output load capacitance DC offset voltage signal-to-noise ratio reference voltage Vo = 1 V (RMS); fi = 1 kHz; ITU-R BS.468 weighted; quasi peak Vi = Vo = 1 V (RMS); fi = 1 kHz; bandwidth = 20 Hz to 20 kHz between any analog input pairs; fi = 1 kHz between left and right of each input pair THD < 3 % Vi(max) = 1 V (RMS) Vi(max) = 2 V (RMS)
[3] [2]
12 11 2 375 12 30 -
mV mV mV mV dB MHz k pF mV V mV V k k k nF mV dB
in addition to 0 dB and 10 dB switch default pre-gain selection for pin SIF (0 dB)
10 150 10 70
Analog audio inputs (pins LEFT1, RIGHT1, LEFT2 and RIGHT2) and outputs (pins OUT_LEFT and OUT_RIGHT)
[4]
[3]
THD+N
0.1
0.3
ct cs
60 60
dB dB
SAA7131E_3
44 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Audio and video decoder characteristics continued Parameter Conditions Min Typ Max Unit
Sound demodulator performance[5] Audio AM mono characteristics (DDEP standard code = 10, driven with external SSIF) S/N signal-to-noise ratio AM carrier 6.5 MHz; 54 % AM; fi = 1 kHz; second SIF AGC off; ITU-R BS.468 weighted; quasi peak AM carrier 6.5 MHz; 54 % AM; fi = 1 kHz; second SIF AGC off; ITU-R BS.468 weighted; quasi peak from 20 Hz to 15 kHz; fref = 1 kHz; no clipping BTSC stereo with L or R only; 100 % modulation; fi = 1 kHz; unweighted RMS BTSC stereo with L or R only; 100 % modulation; fi = 1 kHz; unweighted RMS L or R only; 50 Hz to 10 kHz 10 % EIM 1 % to 66 % EIM Gf frequency gain variation 30 % modulation; fref = 1 kHz stereo; L or R only mono; L = R 0.4 to +1.5 0.2 to +0.04 59 dB dB
[7] [7] [6] [6]
47
dB
THD+N
[6]
0.43
Gf
0.5 to +0.1
dB
Audio M standard BTSC characteristics (DDEP standard code = 13, driven with external SSIF) S/N 77 dB
THD+N
[6]
0.23
cs(stereo)
32 27
dB dB
Audio M standard SAP characteristics (DDEP standard code = 13, driven with external SSIF) S/N signal-to-noise ratio 100 % modulation; fi = 1 kHz; compromise de-emphasis (register SAPDBX = 0b); bandwidth = 0 kHz to 15 kHz; unweighted RMS 100 % modulation; fi = 1 kHz; compromise de-emphasis (register SAPDBX = 0b); bandwidth = 0 kHz to 15 kHz; unweighted RMS
[6]
dB
THD+N
[6]
0.27
SAA7131E_3
45 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Audio and video decoder characteristics continued Parameter signal-to-noise ratio Conditions 100 % modulation; fi = 1 kHz; unweighted RMS EIAJ stereo with L or R; at EIAJ decoder output EIAJ dual; at EIAJ sub-channel decoder output
[6]
Min
Typ
Max
Unit
Audio M standard EIAJ characteristics (DDEP standard code = 14, driven with external SSIF)
61 59
dB dB
[8]
THD+N
100 % modulation; fi = 1 kHz; unweighted RMS EIAJ stereo with L or R; at EIAJ decoder output EIAJ dual; at EIAJ sub-channel decoder output
[6]
0.17 0.8
% %
[8]
ct(dual)
cs(stereo)
Gf
EIAJ stereo; from 20 Hz to 12 kHz; 15 % modulation; fref = 1 kHz FM radio stereo with L or R only; 10.7 MHz carrier; 100 % modulation; fi = 1 kHz; 75 s de-emphasis; unweighted RMS FM radio stereo with L or R only; 10.7 MHz carrier; 100 % modulation; fi = 1 kHz; 75 s de-emphasis; unweighted RMS 60 % modulation; selective RMS; pre-emphasis off; 100 Hz to 14 kHz
[6]
Audio FM radio characteristics (DDEP standard code = 15 to 18, driven with external SSIF) S/N signal-to-noise ratio 55 dB
THD+N
[6]
0.2
cs(stereo)
45 to 55
dB
SAA7131E_3
46 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Audio and video decoder characteristics continued Parameter frequency gain variation Conditions FM radio stereo; from 20 Hz to 15 kHz; 10.7 MHz carrier; 75 s de-emphasis; 30 % modulation; fref = 1 kHz nominal pilot level and identication frequency; no overmodulation European system Japanese system [9] [9] [9]
Min -
Max -
Unit dB
Audio identication of EIAJ mono/stereo (Japanese) standards, driven with external SSIF mpilot modulation degree of pilot tone
10 21 981.9 to 983.0 979.7 to 985.1 921.8 to 923.0 919.3 to 925.8 2 0.5 2 0.5 65 0.25 0.3 0.5
% % Hz Hz Hz Hz s s s s ms s s s
fident
identication frequency M standard (EIAJ) window stereo; slow mode stereo; fast mode slow mode fast mode
td(on)(ident) td(off)(ident)
Audio Automatic Standard Detection (ASD) timing; STDSEL = 1Dh tasd(mono) tasd(stereo) mono automatic default threshold settings standard detection time stereo automatic BTSC stereo standard detection time BTSC SAP EIAJ All digital I/Os: GPIO pins and BST test pins (5 V tolerant) Pins GPIO0 to GPIO23, V_CLK, GPIO25 to GPIO27, TDID, TDOD, TMSD, TCKD and TRSTD_N VIH VIL ILI IL(I/O) Ci VOH VOL HIGH-level input voltage LOW-level input voltage input leakage current leakage current (I/O) input capacitance HIGH-level output voltage LOW-level output voltage 3.3 V signal levels at VDDD 3.3 V I/O at high-impedance IO = 2 mA IO = 2 mA 2.0 0.3 2.4 0 5.5 +0.8 1 10 8 VDDD + 0.5 0.4 V V A A pF V V
SAA7131E_3
47 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Audio and video decoder characteristics continued Parameter pull-down resistance pull-up resistance Conditions VI = VDDD VI = 0 V Min Typ 50 50 Max Unit k k
Audio-video port outputs (digital video stream from comb lter decoder or scaler, digital audio from sound decoder or baseband audio inputs through I2S-bus) LLC and LLC2 clock output on pin V_CLK; see Figure 13 Co(L) Tcy output load capacitance cycle time duty cycle LLC active LLC2 active CL = 40 pF LLC active LLC2 active tr tf Co(L) th(o) tPD rise time fall time output load capacitance output hold time propagation delay LLC active LLC2 active from positive edge of signal V_CLK LLC active LLC2 active
[1]
[11][12] [11][12] [10]
15 35 70 35 35 15 5 15
50 39 78 65 65 5 5 50 -
pF ns ns % % ns ns pF ns ns
Video data output with respect to signal V_CLK on pins GPIO0 to GPIO17, GPIO22 and GPIO23; see Figure 13
28 55
ns ns
Nominal analog video input signal is to be terminated by 75 that results in 1 V (p-p) amplitude. This termination resistor should be split into 18 and 56 , and the dividing tap should feed the video input pin, through a coupling capacitor of 47 nF, to achieve a control range from 3 dB (attenuation) to +6 dB (amplication) for the internal automatic gain control. Lower limit of AGC Denition of levels and level setting: a) The full-scale level for analog audio signals VFS = 0.8 V (RMS). The nominal level at the digital crossbar switch is dened at 15 dB (FS). b) Nominal audio input levels: external, mono, Vi = 180 mV (RMS); 15 dB (FS). The analog audio inputs (pins LEFT1, RIGHT1, LEFT2 and RIGHT2) are supported by two input levels: 1 V (RMS) and 2 V (RMS), selectable independently per stereo input pair, LEFT1, RIGHT1 and LEFT2, RIGHT2. VDDA = 3.3 V; Vi(SIF) = 196 mV (RMS); level and gain settings according to Table note [3]; for external components see the application diagram in the Application Notes SAA7131E; unless otherwise specied. Characterizing AM demodulator or measured at BTSC, SAP, EIAJ or FM decoder output, respectively. Effective Input Modulation (EIM) means 75 s de-emphasis applied to audio input signals of the BTSC stereo encoder. Characterizing EIAJ sub-channel decoder output. Detection times are the same for multi-channel sound standard detection.
[2] [3]
[10] The denition of the duty factor: = t clk ( H ) T cy [11] The output timing must be measured with the load of a 30 pF capacitor to ground and a 500 resistor to 1.4 V. [12] Signal V_CLK inverted; not delayed (default setup).
SAA7131E_3
48 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
0.4 V
1.5 V
3-STATE OUTPUT ton toff tsu th 2.4 V INPUT 1.5 V input valid 1.5 V 0.4 V
mgg280
t PD th
video data and control output (pins GPIO0 to GPIO17, GPIO22 and GPIO23)
t clk(H) t clk(L)
2.4 V 0.4 V
2.4 V
1.5 V 0.4 V tf tr
mhc002
Fig 13. Data output timing (video data, control outputs and raw DTV/DVB)
SAA7131E_3
49 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
TS data and control input (pins GPIO0 to GPIO7, GPIO16, GPIO19, GPIO21 and GPIO22)
t su(D) t h(D)
2.0 V 0.8 V
2.0 V
1.5 V 0.8 V tr tf
mhc003
Fig 14. Data input timing (TS data and control inputs) Table 27. Standard Specication of crystal and related applications (examples)[1] Crystal frequency 24.576 MHz Fundamental 2B Crystal specication Typical load capacitance Maximum series resonance resistance Typical motional capacitance Maximum parallel capacitance Maximum permissible deviation Maximum temperature deviation External components Typical load capacitance at pin XTALII Typical load capacitance at pin XTALOI Typical capacitance of LC lter Typical inductance of LC lter
[1]
20 30 20 7 30 30 27 27 -
User Manual SAA7131E, describing the programming aspects Application Notes SAA7131E, focusing on recommendations for system
implementation
SAA7131E_3
50 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Instruction
CLAMP
IDCODE
SAA7131E_3
51 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
MSB 31 TDID 28 27 0111 0001 0011 0011 16-bit part number 12 11 000 0001 0101 11-bit manufacturer identification 1
LSB 0 1 TDOD
0001
mandatory
001aab219
MSB 31 TDII 28 27 1000 0010 1001 0000 16-bit part number 12 11 000 0010 1011 11-bit manufacturer identification 1
LSB 0 1 TDOI
0000
mandatory
001aab220
SAA7131E_3
52 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
e1 e 1/2 e b
v M C A B w M C T R P N M L K J H G F E D C B A
C y1 C y
e2 1/2 e
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
X
0 5 scale 10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max 1.55 A1 0.45 0.35 A2 1.1 0.9 b 0.55 0.45 D 17.2 16.8 E 17.2 16.8 e 1 e1 15 e2 15 v 0.25 w 0.1 y 0.12 y1 0.35
EUROPEAN PROJECTION
53 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Through-hole components Leaded or leadless SMDs, which are glued to the surface of the printed circuit board
Not all SMDs can be wave soldered. Packages with solder balls, and some leadless packages which have solder lands underneath the body, cannot be wave soldered. Also, leaded SMDs with leads having a pitch smaller than ~0.6 mm cannot be wave soldered, due to an increased probability of bridging. The reow soldering process involves applying solder paste to a board, followed by component placement and exposure to a temperature prole. Leaded packages, packages with solder balls, and leadless packages are all reow solderable. Key characteristics in both wave and reow soldering are:
Board specications, including the board nish, solder masks and vias Package footprints, including solder thieves and orientation The moisture sensitivity level of the packages Package placement Inspection and repair Lead-free soldering versus SnPb soldering
Process issues, such as application of adhesive and ux, clinching of leads, board
transport, the solder wave parameters, and the time during which components are exposed to the wave
54 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Lead-free versus SnPb soldering; note that a lead-free reow process usually leads to
higher minimum peak temperatures (see Figure 18) than a SnPb process, thus reducing the process window
Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
Reow temperature prole; this prole includes preheat, reow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic). In addition, the peak temperature must be low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classied in accordance with Table 30 and 31
Table 30. SnPb eutectic process (from J-STD-020C) Package reow temperature (C) Volume (mm3) < 350 < 2.5 2.5 Table 31. 235 220 Lead-free process (from J-STD-020C) Package reow temperature (C) Volume (mm3) < 350 < 1.6 1.6 to 2.5 > 2.5 260 260 250 350 to 2000 260 250 245 > 2000 260 245 245 350 220 220
Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reow soldering, see Figure 18.
SAA7131E_3
55 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
temperature
peak temperature
time
001aac844
For further information on temperature proles, refer to Application Note AN10365 Surface mount reow soldering description.
15. Abbreviations
Table 32. Acronym 2CS A/V AC-3 ACPI ADC AFC AGC AM ATSC AVL BSDL BST BTSC CC CD-ROM CGMS CIF CMOS
SAA7131E_3
Abbreviations Description 2-Carrier System Audio and Video Audio Code 3 (Dolby Digital) Advanced Conguration Power Interface Analog-to-Digital Converter Automatic Frequency Control Automatic Gain Control Amplitude Modulation Advanced Television Systems Committee Automatic Volume Levelling Boundary Scan Description Language Boundary Scan Test Broadcast Television Systems Committee Closed Captioning (in running text) Color Carrier (in Characteristics) Compact Disk Read Only Memory Copy Guard Management System Common Intermediate Format[1] Complementary MOS
NXP B.V. 2008. All rights reserved.
56 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Abbreviations continued Description Central Processing Unit Composite Video Blanking Sync[2] Digital-to-Analog Converter Demodulator and Decoder Easy Programming Direct Memory Access Digital MultiStandard Decoder Differential Quadrature Phase Shift Keying Digital Signal Processor Digital TeleVision Digital Video Broadcasting DVB-Cable DVB-Satellite DVB-Terrestrial Digital Video Disc Digital Video Recorder End of Active Video Electrically Erasable Programmable Read-Only Memory Electronic Industries Alliance Electronic Industries Association of Japan Effective Input Modulation Electronic Program Guide Federal Communications Commission Field-ID First-in First-Out Finite-Impulse Response Frame-Locked Clock Frequency Modulation Full-Scale Group Delay Equalizer General Purpose Input/Output Horizontal/Vertical Half-Amplitude Duration Inter-IC-Connection Inter-IC Sound Input/Output Integrated Circuit IDentier International Electrotechnical Commission Institute of Electrical and Electronics Engineers Intermediate Frequency INTerrupt
NXP B.V. 2008. All rights reserved.
Table 32. Acronym CPU CVBS DAC DDEP DMA DMSD DQPSK DSP DTV DVB DVB-C DVB-S DVB-T DVD DVR EAV EEPROM EIA EIAJ EIM EPG FCC FID FIFO FIR FLC FM FS GDE GPIO H/V HAD I2C I2S I/O IC ID IEC IEEE IF INT
SAA7131E_3
57 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Abbreviations continued Description Institute of Radio Engineers Interrupt ReQuest International Telecommunication Union ITU-Radiocommunication sector ITU-Telecommunication standardization sector Joint Test Action Group Joint Electron Device Engineering Council Japan Electronics and Information Technology industrial Association Line-Locked Clock Memory Management Unit Metal-Oxide-Semiconductor Motion Picture Experts Group MultiPleX MUltipleXer North American Broadcast Text System Near-Instantaneously Companded Audio Multiplex Neighbor Picture Carrier Neighbor Sound Carrier National Television Systems Committee Operating System Phase Alternating Line Personal Computer (in running text) Picture Carrier (in Characteristics) Peripheral Component Interconnect Phase-Locked Loop Program Stream Personal Video Recorder Pulse Width Modulation Quadrature Amplitude Modulation Quadrature Frequency Division Modulation Quasi Split Sound Resistor Capacitor (electrical lter network) Radio Frequency Red-Green-Blue (additive color space) Reduced Instruction Set Computing Root Mean Square Secondary Audio Program Start of Active Video Surface Acoustic Wave Sound Carrier Syndicat des Constructeurs dAppareils Radiorcepteurs et Tlviseurs
NXP B.V. 2008. All rights reserved.
Table 32. Acronym IRE IRQ ITU ITU-R ITU-T JTAG JEDEC JEITA LLC MMU MOS MPEG MPX MUX NABTS NICAM NPC NSC NTSC OS PAL PC PCI PLL PS PVR PWM QAM QFDM QSS RC RF RGB RISC RMS SAP SAV SAW SC SCART
SAA7131E_3
58 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Abbreviations continued Description Systeme Electronique Couleur Avec Mmoire (French color TV standard) Sound IF Special Interest Group Surface Mounted Device Start Of Packet Second SIF Test Access Port Total Harmonic Distortion Transport Stream TeleVision United Kingdom UNIpleXed information and computing system United States of America Video Electronics Standards Association Vertical Blanking Interval Video Cassette Recorder Video Graphic Adapter VESA video Interface Port Vertical Interval Time Codes Video Module Interface Video Programming System Vestigial SideBand modulation Vertical Interval Time Codes Wide Screen Signaling World System Teletext CrystTAL[3] Zoom Video
Table 32. Acronym SECAM SIF SIG SMD SOP SSIF TAP THD TS TV UK UNIX USA VESA VBI VCR VGA VIP VITC VMI VPS VSB VITC WSS WST XTAL ZV
[1] [2] [3]
CIF is a video resolution of 352 240 pixel (NTSC) and 352 288 pixel (PAL). CVBS is also known as composite video signal. X became a synonym for Crys.
16. Glossary
dbx American company, which has invented the dbx-TV noise reduction system used within BTSC as based on dynamic compression. FM A2 FM modulated sound system based on 2 analog carriers, transporting either the signals (L + R) / 2 and 2R or the dual signals A and B. Hilbert, David German mathematician; so-called Hilbert transformation is a special way to lter signals. Incredible Mono An algorithm which adds stereo-like sound impression to monaural audio signals.
SAA7131E_3 NXP B.V. 2008. All rights reserved.
59 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Incredible Stereo An algorithm which makes stereo sound impression wider. The distance between the two loudspeakers seems to become greater. IRE A unit of an arbitrary scale dividing the 1 V (p-p) video signal from the bottom of sync (40 IRE) to the peak white level (+100 IRE) into 140 equal units. The active video range lasts from 0 IRE to 100 IRE. LCR Electrical lter network which uses inductors (L), capacitors (C) and resistors (R). MPEG-2 Standard for A/V coding and data compression; successor of MPEG-1. Nyquist, Harry American physicist, who developed modern sampling theory. PCTV An application which allows to watch TV on a PC. PowerPC Performance optimization with enhanced RISC Performance Chip S-video Separated video (signals for luminance Y and modulated chrominance C) YUV Component video (signals for luminance Y and chrominance vectors U,V)
17. References
[1] [2] BS.468 ITU-R Recommendation concerning Broadcasting (Sound): Measurement of audio-frequency noise voltage level in sound broadcasting BT.601 ITU-R Recommendation concerning Broadcasting (Television): Studio encoding parameters of digital television for standard 4 : 3 and wide-screen 16 : 9 aspect ratios BT.656 ITU-R Recommendation concerning Broadcasting service (Television): Interfaces for digital component video signals in 525-line and 625-line television systems operating at the 4 : 2 : 2 level of ITU-R BT.601 (Part A) JESD22-114-D JEDEC Standard 22, Test Method A114-D (preferably used): Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM) JESD22-115-A JEDEC Standard 22, Test Method A115-A (currently not used): Electrostatic Discharge (ESD) Sensitivity Testing Machine Model (MM) J.61 ITU-T Recommendation for cable networks and transmission of television, sound programme and other multimedia signals: Transmission performance of television circuits designed for use in international connections IEEE 1149.1 IEEE Standard Test Access Port and Boundary Scan Architecture according to JTAG, issued in 1990, 1993, 1994 and 2001.
[3]
[7]
SAA7131E_3
60 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors Legal texts have been adapted to the new company name where appropriate Selective improvements in style or wording Update of other ICs mentioned Update due to package change (Section 2.1, Table 1, Figure 3 and Figure 17) Harmonized content of Table 3 with table title captions from Section 6.2 Update of hexadecimal notation (Figure 6) Corrected error in Revision ID, see Table 14 Adjusted Symbols and Parameters to latest standards (Section 8 to Section 10) Rearranged data to improve clarity (Section 8 and Section 10) Changed table title captions to improve readability (Table 24 to Table 26) Update of symbols (Figure 13) Update of binary notation (Figure 15 and Figure 16) Moved former chapter Related documents to Section 11 New: Abbreviations, Glossary and References (Section 15 to Section 17) Product data sheet Product data sheet SAA7131E_1 -
SAA7131E_2 SAA7131E_1
20050610 20041209
SAA7131E_3
61 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
Denition This document contains data from the objective specication for product development. This document contains data from the preliminary specication. This document contains the product specication.
Please consult the most recently issued document before initiating or completing a design. The term short data sheet is explained in section Denitions. The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
19.2 Denitions
Draft The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales ofce. In case of any inconsistency or conict with the short data sheet, the full data sheet shall prevail.
Limiting values Stress above one or more limiting values (as dened in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/prole/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
19.3 Disclaimers
General Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customers own risk. Applications Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specied use without further testing or modication.
19.4 Licenses
ICs with Macrovision copyright protection technology This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Purchase of NXP ICs with digital dbx-TV noise reduction functionality Licensed Chips Purchase of NXP Semiconductors ICs with digital dbx-TV noise reduction functionality for which on top of the IC price, the related THAT Corporation royalty payment is paid to NXP Semiconductors, includes a license from THAT Corporation to use the ICs in a BTSC decoding application. Unlicensed Chips Purchase of NXP Semiconductors ICs with digital dbx-TV noise reduction functionality for which on top of the IC price, no related THAT Corporation royalty payment is paid to NXP Semiconductors, is only permitted to parties who according to information supplied to NXP Semiconductors by THAT Corporation, have a BTSC set-maker license from THAT Corporation, 45 Summer street, Milford, Massachusetts 01757-1656, USA.
SAA7131E_3
62 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
19.5 Patents
Notice is herewith given that the subject device uses one or more of the following patents and that each of these patents may have corresponding patents in other jurisdictions. US 4907093 owned by Macrovision Corporation
19.6 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus logo is a trademark of NXP B.V. Silicon Tuner is a trademark of NXP B.V.
SAA7131E_3
63 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
21. Tables
Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Ordering information . . . . . . . . . . . . . . . . . . . . .5 Pin allocation table . . . . . . . . . . . . . . . . . . . . . . .7 Pin description overview . . . . . . . . . . . . . . . . . .9 Power supply pins . . . . . . . . . . . . . . . . . . . . . .10 JTAG test interface pins (for boundary scan test) . . . . . . . . . . . . . . . . . .10 Digital control pins . . . . . . . . . . . . . . . . . . . . . .11 I2C-bus slave interface . . . . . . . . . . . . . . . . . . .11 PCI interface pins . . . . . . . . . . . . . . . . . . . . . .11 GPIO pins and functions, audio and video decoder part [1] . . . . . . . . . . . . . . . . . . . . . . . . .12 Analog interface pins . . . . . . . . . . . . . . . . . . . .13 Crystal oscillator pins . . . . . . . . . . . . . . . . . . . .14 Pins for test purposes [1] . . . . . . . . . . . . . . . . . .14 Pin type description . . . . . . . . . . . . . . . . . . . . .15 PCI conguration space registers . . . . . . . . . .20 Power management . . . . . . . . . . . . . . . . . . . . .21 FIFO conguration; typical example . . . . . . . .21 FIFO conguration; fastidious example . . . . . .21 Overview of basic TV standards . . . . . . . . . . .23 TV system color standards . . . . . . . . . . . . . . .24 TV stereo sound standards . . . . . . . . . . . . . . .24 TV sound decoding, supported feature processing and sampling rate . . . . . . . . . . . . .32 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . .36 Thermal characteristics . . . . . . . . . . . . . . . . . .36 Supply characteristics . . . . . . . . . . . . . . . . . . .37 IF demodulator characteristics . . . . . . . . . . . . .38 Audio and video decoder characteristics . . . . .43 Specication of crystal and related applications (examples)[1] . . . . . . . . . . . . . . . .50 Boundary scan test naming conventions . . . . .51 BST instructions supported by the SAA7131E 51 SnPb eutectic process (from J-STD-020C) . . .55 Lead-free process (from J-STD-020C) . . . . . .55 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . .56 Revision history . . . . . . . . . . . . . . . . . . . . . . . .61
SAA7131E_3
64 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
22. Figures
Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Fig 17. Fig 18. Application diagram for capturing live TV video and audio streams in the PC . . . . . . . . . . . . . . . . .1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Pin conguration LBGA256 (SOT740-2) . . . . . . . .7 Functional diagram of the low-IF part . . . . . . . . .16 Functional diagram of the PCI audio and video decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 MMU implementation (shown bit width indication is valid for 4 kB mode) . . . . . . . . . . . . . . . . . . . . .22 Scaler processing with DMA interfacing . . . . . . .27 Example of scaler task processing with DMA interfacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Nominal digital levels for YUV (Y, CB and CR) in accordance with ITU-R BT.601 . . . . . . . . . . . .30 Nominal digital levels for CVBS and raw VBI samples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Color space conversion and look-up table . . . . . .30 PCI I/O timing. . . . . . . . . . . . . . . . . . . . . . . . . . . .49 Data output timing (video data, control outputs and raw DTV/DVB). . . . . . . . . . . . . . . . . . . . . . . .49 Data input timing (TS data and control inputs). . .50 32 bits of identication code, decoder part . . . . .52 32 bits of identication code, IF demodulator part. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 Package outline SOT740-2 (LBGA256) . . . . . . . .53 Temperature proles for large and small components . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
SAA7131E_3
65 of 66
NXP Semiconductors
SAA7131E
Global standard low-IF and PCI audio and video decoder
23. Contents
1 2 2.1 2.2 2.3 2.4 2.5 2.6 3 4 5 6 6.1 6.2 7 7.1 7.2 7.2.1 7.2.2 7.2.3 7.2.4 7.2.5 7.2.6 7.3 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 7.5 7.6 7.6.1 7.6.2 7.6.3 7.6.4 7.6.5 7.6.6 7.6.7 7.6.8 7.6.9 7.7 7.7.1 7.7.2 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Generic properties . . . . . . . . . . . . . . . . . . . . . . 2 Digital global standard low-IF demodulator for analog TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 TV video decoder and video scaling. . . . . . . . . 3 TV sound decoder and TV audio I/O . . . . . . . . 3 PCI and DMA bus mastering . . . . . . . . . . . . . . 4 Peripheral interface. . . . . . . . . . . . . . . . . . . . . . 4 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ordering information . . . . . . . . . . . . . . . . . . . . . 5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pinning information . . . . . . . . . . . . . . . . . . . . . . 7 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 9 Functional description . . . . . . . . . . . . . . . . . . 15 General description. . . . . . . . . . . . . . . . . . . . . 15 Internal functions of the low-IF demodulator. . 16 Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Carrier synchronization. . . . . . . . . . . . . . . . . . 16 Nyquist lter . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Video output . . . . . . . . . . . . . . . . . . . . . . . . . . 17 SSIF output. . . . . . . . . . . . . . . . . . . . . . . . . . . 17 IF AGC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Internal functions of the PCI audio and video decoder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 PCI interface . . . . . . . . . . . . . . . . . . . . . . . . . . 19 PCI conguration registers . . . . . . . . . . . . . . . 19 ACPI and power states . . . . . . . . . . . . . . . . . . 20 DMA and congurable FIFO . . . . . . . . . . . . . . 20 Virtual and physical addressing . . . . . . . . . . . 21 Status and interrupts on PCI-bus . . . . . . . . . . 22 Analog TV standards . . . . . . . . . . . . . . . . . . . 22 Video processing . . . . . . . . . . . . . . . . . . . . . . 25 Analog video inputs . . . . . . . . . . . . . . . . . . . . 25 Video synchronization and line-locked clock . 25 Video decoding and automatic standard detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Adaptive comb lter . . . . . . . . . . . . . . . . . . . . 26 Macrovision detection . . . . . . . . . . . . . . . . . . . 26 Video scaling . . . . . . . . . . . . . . . . . . . . . . . . . 26 VBI data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Signal levels and color space . . . . . . . . . . . . . 29 Video port, ITU and VIP codes . . . . . . . . . . . . 31 Sound processing . . . . . . . . . . . . . . . . . . . . . . 32 TV sound stereo decoding . . . . . . . . . . . . . . . 32 Additional audio features . . . . . . . . . . . . . . . . 33 7.7.3 7.7.4 Audio interfaces . . . . . . . . . . . . . . . . . . . . . . . Default analog audio pass-through and loopback cable . . . . . . . . . . . . . . . . . . . . . . . . 7.7.5 FM radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8 DTV/DVB channel decoding and MPEG TS or PS capture . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 Control of peripheral devices . . . . . . . . . . . . . 7.9.1 I2C-bus master . . . . . . . . . . . . . . . . . . . . . . . . 7.9.2 Propagate reset . . . . . . . . . . . . . . . . . . . . . . . 7.9.3 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 9 Thermal characteristics . . . . . . . . . . . . . . . . . 10 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 IF demodulator . . . . . . . . . . . . . . . . . . . . . . . . 10.3 Audio and video decoder . . . . . . . . . . . . . . . . 11 Support information . . . . . . . . . . . . . . . . . . . . 11.1 Related documents . . . . . . . . . . . . . . . . . . . . 12 Test information. . . . . . . . . . . . . . . . . . . . . . . . 12.1 Boundary scan test . . . . . . . . . . . . . . . . . . . . 12.1.1 Initialization of boundary scan circuit . . . . . . . 12.1.2 Device identication codes. . . . . . . . . . . . . . . 13 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 14 Soldering of SMD packages . . . . . . . . . . . . . . 14.1 Introduction to soldering. . . . . . . . . . . . . . . . . 14.2 Wave and reow soldering . . . . . . . . . . . . . . . 14.3 Wave soldering. . . . . . . . . . . . . . . . . . . . . . . . 14.4 Reow soldering. . . . . . . . . . . . . . . . . . . . . . . 15 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . 16 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . 19 Legal information . . . . . . . . . . . . . . . . . . . . . . 19.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19.2 Denitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 19.4 Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5 Patents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.6 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Contact information . . . . . . . . . . . . . . . . . . . . 21 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 33 34 34 34 34 34 35 36 36 37 37 38 43 50 50 51 51 51 52 53 54 54 54 54 55 56 59 60 61 62 62 62 62 62 63 63 63 64 65 66
Please be aware that important notices concerning this document and the product(s) described herein, have been included in section Legal information.
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 19 May 2008 Document identifier: SAA7131E_3