Documente Academic
Documente Profesional
Documente Cultură
SWI 3.2
Remember in the CSWIP 3.2 Senior Welding Inspectors examination your are required to interpret a fabrication drawing and comment on the welding symbols
M.S.Rogers
SWI 3.2
SWI 3.2
M.S.Rogers
SWI 3.2
1. Welded arrow side: Single-J butt, flat (flush) finish. Welded other side: 12mm leg length fillet weld.
2. Welded arrow side: Single-bevel butt partial penetration, depth of preparation 25mm. Welded other side: 6mm leg length fillet weld, welded all way around, Drawing indicates the pipe to be prepared incorrect set-up 3. Welded both sides: 12mm leg length fillet weld, toes blended smooth, welded all way round (peripheral weld). After welding is completed MT to be carried out.
4. Welded arrow side: Single-bevel butt weld, smooth finish. Welded other side: 12mm leg length fillet weld.
M.S.Rogers
SWI 3.2
5. Welded both sides: Double-bevel butt weld with a broad root face, A.1 reference symbol indicates specific instructions e.g. procedure sheet.
6. Welded arrow side: Single-J butt depth of preparation 50mm with a 35mm leg length fillet weld superimposed, toes shall be blended smooth Welded other side: 8mm leg length fillet weld
7.
Welded arrow side: Steep-flanked single-bevel butt with a 12mm leg length fillet weld superimposed. Welded other side: 12mm leg length fillet weld.
M.S.Rogers
SWI 3.2
9.
11. Welded arrow side: Single-J butt with a 25mm leg length fillet weld superimposed, reference symbol indicates specific instruction.
12. Welded arrow side: Double bevel butt weld, 16mm leg length fillet weld superimposed, weld to be made all way around component. Note: fillet weld should be placed on other side.
Copyright 2003 TWI Ltd
M.S.Rogers
SWI 3.2
20
13. Welded both sides: Five fillet welds 8mm leg lengths, Length of each weld 20mm distance between each weld 20mm
20
20
20
14. Welded arrow side: 35mm leg length fillet weld concave profile
15. Welded arrow side: 12mm leg length, welded all way around part (peripheral) weld
16. Welded other side: 12mm leg length,concave profile welded all way around part (peripheral) weld
M.S.Rogers
SWI 3.2
17. Welded both sides: Double-bevel butt with a 12mm leg length fillet weld superimposed peripheral weld. After welding to be inspected with UT.
25
18. Welded both sides: Three 16mm leg length fillet welds, each weld 25mm in length, gap between each weld 50mm welds to be staggered.
25
50
25
50
19. Welded both sides: Three 12mm leg length fillet welds, each weld 50mm in length, To be welded with the MAG process.
50
20. Welded arrow side: Single-bevel butt weld with a 10mm leg length fillet weld superimposed, peripheral weld. After welding weld to be inspected with UT
Copyright 2003 TWI Ltd
M.S.Rogers
SWI 3.2
21. Welded both sides: Single-J butt, flush finish, peripheral weld
22. Welded arrow side: Steep-flanked single-V butt, flat (flush finish). Welded other side: Backing run flat (flush) finish, weld to be made all around the part welded using the MAG process
23. Welded both sides: Double-U butt weld, flat (flush finish peripheral weld.
M.S.Rogers
SWI 3.2
24. Welded arrow sides: Convex single-V butt weld with permanent backing strip.
25. Welded both sides: Concave fillet weld with 12mm leg lengths. MT inspection required.
M.S.Rogers