Documente Academic
Documente Profesional
Documente Cultură
www.huawei.com
Foreword
Be familiar with OSN 38006800 equipments. Illustrate the basic signal flow of OSN 38006800 equipments. Understand the functions of cards of OSN 38006800 equipments.
Page1
Objectives
Page2
Contents
1. 2. 3.
Page3
Contents
1. Preparations for Commissioning
1.1 Instruments and Tools 1.2 Engineering Design Information 1.3 Requirements on Commissioning Engineers
Page4
Used to install the Web LCT network management system during the network element (NE) commissioning. Used to weaken the light received by an optical interface. Used to transfer the fiber jumper.
Fiber jumper Used for connections Copyright 2008 Huawei Technologies Co., Ltd. All rights reserved.
Network diagram Board layout diagram of the cabinet Wavelength allocation table Configuration diagram of optical amplifiers Fiber connection diagram
Page6
SDH, PDH, WDM and Ethernet theories. OptiX OSN 3800/6800. T2000 or Web LCT, and is skillful at using it for configuring services.
Page7
Questions
the commissioning?
Page8
Contents
1. 2. 3.
Page9
Contents
2. Single-station Commissioning
2.1 Single-Station Hardware Check 2.2 Power-on Check 2.3 Sub-rack Power-on Test 2.4 Setting the NE ID and IP 2.5 Single-station ECC commissioning 2.6 Single-Station Parameter Testing 2.7 Ending
Page10
Grounding of the sub-rack. No screws, broken & bended pins on the backplane etc.
Power supply cables, grounding cables, external alarms wiring and patch cords.
Page11
Door
Page12
DCM
Make sure DCMs are correctly installed. Make sure the DCMs are compliant with the design document.
Page13
Power-on Check
Step Content Testing voltage between the input cable terminals Checking resistance (all switches : OFF Checking resistance Requirements OSN 3800DC -38.4V -72V DC AC 90V285V AC OSN 6800 38.4 V 57.6 V (48 V DC20%) 48.0 V 72.0 V (60 V DC20%) Between NEG1 (-) or NEG2 (-) and RTN1 (+) or RTN2 (+),the value is . Between NEG1(-) or NEG2(-) and PGND, the value is . Between NEG1 (-) or NEG2 (-) and RTN1 (+) or RTN2(+),the value is more than 20 k.
(all switches : ON
Page14
Page15
4 5 6
Page16
Set the NE ID
Page17
Set the NE IP
Page18
CPU
CPU
Representing 1
Representing 0
Representing 0
NM_ETH2
NMS
HUB
Copyright 2008 Huawei Technologies Co., Ltd. All rights reserved.
Page20
ETH1/2/3: cascading between master sub-rack and slave sub-rack. NM_ETH1/2: communication between NE and NE or between NE and NMS.
Cabinet 1
Slave sub-rack 2 ETH1/2/3 Slave sub-rack 1 Cabinet 2
Slave sub-rack 2
Slave sub-rack 1
ETH1/2/3
Master sub-rack
Master sub-rack
NM_ETH1/2 NMS HUB
Page21
Page22
Ending
Page23
Questions
Page24
Contents
3. Network Commissioning
3.1 Requirements of Optical Power Commissioning 3.2 Network Commissioning 3.3 Others Commissioning
Page25
Contents
3.1 Requirements of Optical Power Commissioning
3.1.1 OTU Commissioning 3.1.2 Tributary Board Commissioning 3.1.3 Line Board Commissioning 3.1.4 EDFA Commissioning 3.1.5 Raman Amplifier Commissioning 3.1.6 OSC Board Commissioning 3.1.7 OMU/ODU Commissioning
Page26
OTU Commissioning
Need to adjust the VOA before OTU to close the typical power value at optical amplifier.
Page27
Page28
Need to adjust the VOA before Line board to close the typical power value at optical amplifier.
Page29
EDFA Commissioning
OAU101
HBA
-20/4
-19/10
-23/1
\
24
29
Page30
24~36
29
OAU101 Commissioning
When the input power is higher than the typical value at the
DCM
When the input power is lower than the typical value at receiving end , how to adjust the OA?
Page31
OAU101 Commissioning
Example 1 : Parameters:
Typical input/output power for each channel : -16/+4dBm The signal gain range : 20 ~ 31dB
-18dBm
OAU1
+4dBm
A Case: Input power for each channel : -18dBm In this case, change the Gain into 22dB by
DCM
IL of DCM: 8dB
NMS
Page32
Note :
Page33
OAU101 Commissioning
Example 2 : Parameters:
Typical input/output power for each channel : -16/+4dBm The signal gain range : 2031dB A Case:
-20dBm
OAU1
DCM
IL of DCM: 8dB
Can we adjust the gain to 24dB ? Min. Signal Gain Signal Gain Max. Signal Gain
Page34
Page35
Receiving Range : -48 dBm ~ -3 dBm. Optimal Receiving : -30 dBm. Launched Power : -4 dBm ~ -0 dBm.
Page36
ODU/OMU Commissioning
Adjust the attenuation of the VOAs in each channel of the M40V/D40V to 5 dB before commissioning.
Adjust the VOAs in M40V/D40V to make the optical power (or OSNR) closer to the average value.
Ensure that the maximum difference of optical power among all the
channels is within 4 dB and that of OSNR is within 2 dB.
Page37
Contents
3. Network Commissioning
3.1 Requirements of Optical Power Commissioning 3.2 Network Commissioning 3.3 Others Commissioning
Page38
Contents
3.2 Network Commissioning
3.1.1 Supervisory Channel Commissioning 3.1.2 Transmitting End of OTM 3.1.3 OLA 3.1.4 Receiving End of OTM 3.1.5 FOADM 3.1.6 ROADM
Page39
When the OTU starts to work and the service is normal, the ESC route is set up.
Page40
OLA
Traffic
OTM
Traffic
S C 1
F
OS C
F I U
Traffic OS C
I U
S C 2
F
OS C
F I U
Traffic OS C
I U
S C 1
Traffic
SCC
SCC
SCC
NMS
Page41
A certain NE should be internal clock source, others should trace the clock for synchronizing and processing supervisory signal.
Page42
O T U
M D 4 40 0 M M 4 40 0
O T U
M D 4 40 0 SCC
OAU
OAU
SCC
NMS
Page43
+4+10lgN
+3+10lgN
OTU
OTU
M M 4 40 0
F OBU103 I U
Note : Adjust the attenuation of VOA to make the input optical power
of each wavelength to typical optical power for OBU102. Ptotal (dBm)Psigle (dBm) + 10lgN (dB)
Page44
OLA
-16+10lgN +4+10lgN +3+10lgN
OAU101
F I U PA F
BA
I U
DCM
1. VOA : adjust the input optical power for OAU1 closer to typical power. 2. OAU1 : change the gain to make sure the output power is typical.
3. When the input power is lower than typical power: firstly remove the VOA ,
secondly change the gain of OAU1 to make sure the output power is typical.
Copyright 2008 Huawei Technologies Co., Ltd. All rights reserved.
Page45
M40
OAU1 OPU03
M D40 D 4 40 0
OTU
1. VOA : adjust the input optical power for OAU1 closer to typical power. 2. OAU1 : change the gain to make sure the output power is typical. 3. When the input power is lower than typical power: firstly remove the VOA , secondly change the gain of OAU1 to make sure the output power is typical. 4. VOA : add corresponding fixed attenuator for OTU boards at IN ports.
Page46
FOADM (MR2+MR2)
-16+10lgN +4+10lgN
O T U O T U
O T U O T U
-19+10lgN
+4+10lgN
OAU101
F I U
BA
MR2
MR2
PA
OBU102
I U
DCM
1. VOA : adjust the input optical power for OAU1 closer to typical power, 2. OAU1 : change the gain to make sure the output power is typical. 3. VOA : add corresponding fixed attenuator for OTU boards at IN ports. 4. VOA : adjust the optical power of passing-through channels. 5. VOA : adjust the optical power of added channels.
Page47
FOADM (D40+M40)
-16+10lgN
+4+10lgN
O T U
O O T T U U
O T U
-19+10lgN
+4+10lgN
M F
OAU1
F I U D
PA
BA
4 0
OBU103
I U
DCM
1. VOA : adjust the input optical power for OAU1 closer to typical power. 2. OAU1 : change the gain to make sure the output power is typical. 3. VOA : add corresponding fixed attenuator for OTU boards at IN ports. 4. VOA : adjust the optical power of passing-through channels. 5. VOA : adjust the optical power of the added channels.
Copyright 2008 Huawei Technologies Co., Ltd. All rights reserved.
Page48
ROADM (ROAM+ROAM)
-16+10lgN +4+10lgN
O T U O T U
-3+10lgN
O T U
EXPO
-19+10lgN
OAU1
F I U
D40
DM
O T U F
PA
BA
DCM
ROA M
ROA M
EXPI
OBU103
+4+10lgN
1. VOA : adjust the input optical power for OAU1 closer to typical power.
2. OAU1 : change the gain to make sure the output power is typical. 3. VOA : add corresponding fixed attenuator for OTU boards at IN ports. 4. The VOAs in ROAM and :adjust optical power of passing-through channels.
Page49
ROADM (WSD9+RMU9)
-16+10lgN +4+10lgN
O T U O O T T U U
OAU1
F
I U
O O O T T T U U U D40 M40
-19+10lgN
+4+10lgN
D40
PA
BA
WSD9
RMU9
IN
OBU103
I U
DCM
EXPO
1.
2. 3. 4.
VOA : adjust the input optical power for OAU1 closer to typical power. OAU1 : change the gain to make sure the output power is typical. The VOAs in WSD9 : adjust the optical power of dropped the channels and passing-through channels. VOA and VOAs in RMU9 : adjust the optical power of the added channels.
Page50
ROADM (WSD9+WSM9)
-16+10lgN +4+10lgN
O T U O O T T U U
OAU1
F I U
O O O T T T U U U D40 M40
-19+10lgN
+4+10lgN
D40
PA
BA
WSD9
WSM9
EXPI
OBU103
I U
DCM
EXPO
1. 2. 3. 4. 5.
VOA : adjust the input optical power for OAU1 closer to typical power. OAU1 : change the gain to make sure the output power is typical. The VOAs in WSD9: adjust the optical power of the dropped channels The VOAs in WSD9 and WSM9:adjust optical power of passing-through channels. VOA and VOAs in the WSM9: adjust optical power of the added channels.
Page51
Contents
3. Network Commissioning
3.1 Requirements of Optical Power Commissioning 3.2 Network Commissioning 3.3 Others Commissioning
Page52
Contents
3.2 Others Commissioning
3.2.1 Network parameter testing 3.2.2 Testing bit errors
Page53
end EDFA
Receiving end EDFA
NOTE : Referring to
Page54
Make sure OSNR value is higher than the requirement at receiving end, otherwise bit errors will occur.
The type of OTU at WDM side 2.5G(with FEC) 2.5G(without FEC) 5G(3400ps/nm) (with FEC) 5G(6400ps/nm) (FEC) 10G(without FEC) 10G (with FEC)NRZ 10G (with AFEC)NRZ
Page55
IN
Tx
Rx
Signal Analyzer
OUT Rx
O T U
O T U
Tx
Site A
Site B
Page56
OTU
Signal Analyzer
OTU
OTU
OTU
OTU
IN Tx
OTU
Site A
Site B
Page57
Summary
Page58
RM-OUT
IN-TC RC-OUT
<1.5
MR2
MI-OUT
IN-Dx Ax-OUT
<1.5
<1.5 <1.5
Page59
Ax-OUT
MB2 IN-MRO MRI-OUT IN-BMO
<3
<2 <2 <0.7
IN-DM
EXPI-OUT IN-EXPO IN-DMx
<7
<14 <3 <8
BMI-OUT
EXPIOUT RMU9 AMx-TOA ROAOUT
<0.7
<8.5 <12.5
WSD9
IN-EXPO
AMx-OUT EXPI-OUT
<8
<8 <8
WSM9
<1.5
MR2
IN-MO
MI-OUT
<1
<1
Page60
Thank you
www.huawei.com