Sunteți pe pagina 1din 26

4G LTE TDD/FDD, DT Methologhy, and

Preparation on GENEX ProbeAssistant

Drive Test Conceptual


-

Drive test is conducted for checking coverage criteria of a cell with RF


The data collected by drive test tool as log files is analyzed to evaluated various
RF parameters of the network

Important thing to DT efficient and effective


1. The parameter: a lot of DT Engineer didnt know what he do while drive
testing, it have so many value inside the tools, but they just collect it without
understand what the definition each parameter

2. Route: Dont make double job at the same route,it will waste your time. Please
be aware with your route and dont duplicate it.

3. Event: event is the most important thing, you can see when the event call drop,
handover failure and make the analyze at that time. So you can explain to your
RF Engineer what you have done in your work

4.

DT strategy: the main important thing in LTE is Throughput, that value is


makes differrence between another technology such as 3G / 2G. Please make
sure you record your DT in stable condition (Filezilla still copying file)
- Open large file
- Open 3 file zilla

5. Be active to analyze: some of DT engineer spent all the day to collect the data
without knowing the result, it better for you to focus on your work and see if
there any crossfeeder, bad spot result, or site Down,etc
A. Cross Feeder: which cell is cross feeder?

B. Bad Spot Result


Please give me the valid reason why the throughput is drop?

How To Drive Test Using Genex Probe V 3.5

Open Probe V3.5 then connect LTE Dongle and USB GPS
Klik Configure -> Device management-> Device configure
add the MS, by following this below picture and choose the related COM port

add the MS, by following this below picture and choose the related COM port

Add The GPS NMEA by click add button and choose the COM Port

Create the engineering Parameter in xls format (please use the following format)

Import Engineering Parameter: Configuration ->Engineering parameter


management-> import -> then choose LTE system, click browse and choose the
engineering parameter in xls format. Then click OPEN

Match the probe parameter with the excel parameter (mandatory field)
Click next and make sure there are no failed item

Test Plan Configuration

Set different parameter according to different test, for example FTP Download

4. Set test
parameters

1. Add
test

2. Choose
equipment

3. Test
state

5. Test
statistic

Weekly/Monthly DT Preparation

1. Before
Weekly/Monthly
DT

2. During
Weekly/Monthly
DT
3. After
Weekly/Monthly
DT log process

1.1
1.2
1.3
1.4

Site status
Site alarm
Site transmission & SSV remarks
Neighboring site

1.5 Site DT route cross


1.6 DT FTP files
2.1 DT vehicle speed
2.2 Remarks on every abnormal around site
2.3 Remarks of serving site environment
3.1 Low RSRP; Low SINR; Low Throughput
3.1 High RSRP; Low SINR; Low
Throughput
3.3
High RSRP; High SINR; Low Throughput

1. Before Weekly/Monthly DT
1.1 Site status

Before Weekly/Monthly DT, always ensure the site(s) status.


Which to be on air and include in Weekly/Monthly DT, which are
be alarm
excluded.
1.2to
Site
Before Weekly/Monthly DT, cross check the alarm status
of the site(s).
1.3 Site transmission & SSV
remarks
Cross check on the site transmission issue. Double cross check

with the remarks stated over SSV report. Certain site(s) with
transmission limitation will be remarked over SSV report. Also,
take note of other special remarks stated over SSV report.
1.4 Neighboring site

Cross check NRT of the site to ensure neighbor relations had


been defined.

1. Before Weekly/Monthly DT
1.5 Site DT route
cross
Always cross check the DT route before starting DT. Ensure DT

route doesnt cover low coverage area whereby the planned site
not
integrated
/ up yet.
1.6isDT
FTP
files
Always ensure to perform large files for FTP download
(recommended 1G files, 5~8 files at the same time). DO NOT
perform small files download as might end up with non-stable
peak throughput.

2. During Weekly/Monthly DT:2.1 DT vehicle speed & Logfile

During DT, always ensure the vehicle speed are moving not too
fast nor too slow. Ensure DT log files saved at Example
50~100Mb/files.
of DT speed

2.2 Remarks on every abnormal around site

Always drop down remarks during DT if found any activities / ongoing event around the site or any abnormal found.
2.3 Remarks of serving site environment

Always alert with the DT result and check with the surrounding
environment. Is the serving cell being blocked by high rise
building? Is there any cross feeder? Is there any sleeping cell or
abnormal cell and etc.

Moving Test Method & KPI


A. Moving Test DL

1. Login to FTP Server using Filezilla


and select multiple file for DL.
2. Begin DT in clockwise & anticlockwise directions at least in two
different file.
3. Save the DT log, cross check all KPI
achieved. Ensure naming of log are
correct
4. Fill up the KPI excel sheet, submit to
Vendor within 24 hours

FTP Server:
IP : ????????
UN / PW : xxxxx/ xxxxx

KPI to look into


Download Average min = ???

Cluster Reporting & KPI (Plotting Download (Throughput))


A. Download
Choose DL grup -> search Throughput menu -> right click on PCC MAC Throughput -> Display On Map
You can add some route and legend with click the layer button and legend button

Cluster Reporting & KPI (Plotting Download


(Histogram))
A. Download
-Histogram is very important thing while reporting, RF engineer can analyze the distribution of the
Download value and make decision about the next step
- Choose download -> search Throughput -> PCC MAC Throughput ->Display on Histogram

Cluster Reporting & KPI (Display Statisctics))


A. Download
-Display the statistics is needed to view the valid value for average,maximum,minimum range of the
throughput.
- Choose DL -> search MAC Throughput -> right click and display on sheet

Cluster Reporting & KPI (Plotting Download (add layer & Missing Route))

A. Download
- Click the layer button to add some routes it will make you easier to locate where is the missing route
and create justification at that area

Cluster Reporting & KPI (Plotting Download (EARFC))


A. Download
- EARFCN is using to define the frequency while you Drive Test
- choose DL -> serving cell -> Serving DL EARCN -> display on map

S-ar putea să vă placă și