Documente Academic
Documente Profesional
Documente Cultură
1. Product Introduction
2. Key Features & Operation
3. Front View/Rear View
4. Repair Preparations
5. Layout & Wiring Diagram
6. Circuit Description
7. Troubleshooting
8. Factory Mode
9. Disassembly
CPU CA13( 1.3GHz)
- Voice Interaction
Jig Direction
Jig Direction
5. Gently lift up the Rear Cover from the bottom chassis.
2. Remove the stands with pulling it down.
OPEN JIG
BH81-12884A
2
1
DELPHINUS JIG
BH81-00001A
Remove/Replacing the SMPS and MAIN Boards
ONE CONNECT
SMPS
Main/T-CON
BT/WIFI Module
Function/IR Speaker
Wiring Diagram
ONE CONNECT
CN201
CNM803
CN901
CNL801
MAIN SMPS
CN1701
CN501
CN910 CN2102
Panel
SPEAKER
Function BT/WIFI
LOGO
Block Diagram
Main Board
6
9 8 7 Power
5
Arm Tcon Demura Aging&Mura
Jtag Flash Micom Flash
Dimming 4
USIT Left
USB
10
11 Ex-Link
2
One
13
Connect
14 15 1
Function/IR
BT/Wifi Sound
Main Board Pin Map
One Connect Board
USB2
OPTICAL USB1
3 1
4 5 6 7 8
One Connect HDMI1 HDMI2 HDMI3 HDMI4
One Connect Board Pin Map
SMPS Board & Pin Map
CNL801
CNM803
Function Control
Function Control Operation/Test
Function/IR
CN910
On Screen Selections with Function Control
SMPS
Fuse
SMPS
CNL801
SMPS
CNL801
80Vdc 2. Check each separate backlight supply at the 8 circled capacitors for approx. 80 Vdc by
connecting the multi meter to CH1 through CH8 side of Capacitors. (Ref. Chassis Ground)
25Vdc 3. If any are missing or low, remove the panel connectors and re-test. If it stays low the SMPS
Board is defective. If it goes up to same reading as the other CH supply voltages with the
connector removed, the Panel is defective (a string of LEDs are shorted)
4. Check the eight Capacitors (C9103 through 9803) at each capacitor pin location closest to the
Ref. Chassis Ground transformer. They should measure approximately 25Vdc. If any read much lower (1 or 2 Volts)
(Voltages Vary with Panel Size) and corresponding CH was ok (80V). The Panel is defective (open string of LEDs).
LED DRIVE VOLTAGE (UN48JS9000 Example)
(Voltages Vary with Panel Sizes)
Plus Pins
84VDC +
(48 Models) 1 thru 8
Minus Pins
-
1 thru 8
30VDC MAX Backlight
(48 Models) 54Vdc to Panel
Plus Pins
84VDC
+
(48 Models) 1 thru 8
40VDC
(48 Models)
Minus Pins
-
1 thru 8 Min Backlight
44Vdc to Panel 34
NOTE: Approximate DC Voltages are listed when measured with a Multi Meter & reference to Chassis Ground
Video: Customer
Customer Picture Test
Picture Test
MAIN/TCON BOARD
Main Section Pre- FRC (T-CON) Post FRC ( T-CON)
Check Signal
Source and other
Pass Pass Pass
inputs to One
Connect
Replace
Fail Pass Pass One Connect
Board
Replace
Fail Fail Pass Main/T-CON
Board
Replace
Fail Fail Fail Main/T-CON
Board or Panel
Video
JAZZ-M
2. FRC Pre Test Pattern
FRC
3. Power the TV ON
4. If there is a problem in the One Connect and the TV Panel is OK the disconnect banner will
appear.
Video Operation Video Operation Video Operation Video Operation Video Operation
Generated on Generated at Generated at Generated at T-CON
If No Video Main Section. Pre FRC, of T-CON Post FRC of Section.
Disconnect One Section. T-CON
Connect Cable If OK: Section. If OK:
Source & Input If OK: Main/ T-CON Board
Disconnect Banner
Cables Main Section If OK: (defective)
is displayed
Main/T-CON
If Banner Appears Other inputs If Noisy: (defective) If Noisy:
Post FRC Pattern Main/ T-CON Board
One Connect Box One Connect If Noisy:
/Cable (defective) Cable/Box Mute 369 Mute
If No Banner If Noisy:
continue T-Con Section
Test Patterns
AUDIO Troubleshooting:
AUDIO TEST
No TV Sound
Menu/Audio/Speaker Settings/set to TV Speaker
Noisy/Distorted TV Audio
Customer Menu/Support/ SOUND TEST No HDMI Audio
Source / HDMI Cable & One Connect Mini Connectors
If SOUND TEST FAILS (Missing/Noisy Audio) Swap with other HDMI Inputs/Sources
Speakers (compare resistance/quality) Perform EDID Write in Factory Mode
Compare audio level out to speakers with multi meter. (Can restore missing HDMI Audio).
Replace defective Speakers or Main Board or Cable Bulletins and Latest firmware on TV
If not restored replace One Connect Mini/Main.
IF SOUND TEST OK Check Audio Format PCM/Dolby based on external Receiver
Audio Source & External Cables
With external Audio Generator (device or App) ARC Issues
Other Inputs HDMI Cable is input to the ARC Designated HDMI port
One Connect Mini ARC (HDMI Control) is enabled on the external Receiver.
Optical Digital Out Errors Bluetooth Audio Sound Share Connection Issues
Red light from Optical Digital Out Sound Bar is in TV Mode
If missing replace One Connect Mini To Connect, Press & Hold Play Button until Sound Bar pairing mode
begins.
Network Troubleshooting
TV Router Internet
TV to Router Failure Router to Network Failure
Check Network Status Check Network Status
Pins 1 2 3 4 5 6 7 8 9 1 11 12 13 14 15 16
0
Pwr 3.3V 3.3 3.3V 0.7V 2.5V 0 0 3.3 0 .02V .02V 0 5Vdc 3.3 3.3
On dc Vdc dc eff. dc eff.dc V Vd eff.dc eff.dc VCC Vdc Vdc
BT Sig BT Sig c WiFi Sig WiFi Sig
(DM) (DP) (DP) (DM)
4V P-P 4VP-P 0.5V P-P 0.5V P-P
- Go to Menu/Support/Contact Samsung
. Wired MAC Address (missing or error - replace Main Board)
. Wireless MAC Address
. Bluetooth Address
- If Bluetooth Address or Wireless MAC Address are missing or
errors exist
BT & Wi-Fi Connector Voltages. If Voltages are OK but no BT or
Wi-Fi Signals voltage(s), replace defective Module.
Setting TV into Factory Mode: Important Items:
First Screen
Setting Option Bytes
Appearing in 1. Enter Factory Mode with
Factory Mode Service Remote (only)
2. Check Option Byte Table
located on GSPN (Fast Track
or Tips)
(SAMPLE) 3. Select each item to change
4. Soft power TV Off to load
Check Test Patterns
1. Verify Scaler Pattern and
US Post Pattern
2. Verify FRC Pre Test Pattern
3.Verify FRC Post Test Pattern
4. Verify SoC TCON Test Pattern
SVC / Test Patterns
Jig Direction
Jig Direction
Jig Direction
OPEN JIG(3).
1 3
A B
7. Remove the power cable(A), BLU cable(B)
and the USI-T cables(C).
C
3
8. Disconnect the function cable from the logo
cable(1). Remove the function module from the
bottom chasis(2) and remove the function cable 1
from the main board(3).
2