Sunteți pe pagina 1din 45

LCD Television

Repair Guide Handbook


General 1. ‘13 LCD TV layout structure Overview

Driver Board

Power Board

Woofer Speaker Main Board

Local Key

T con Board

WiFi
Board IR RF Board

1
Repair Method by Symptoms 3-1. No Power Check(Flow Chart)

☞Page 5 ☞Page 6~7


Check Y “DC Power on” N Measure voltage Replace
Front Display
Power LED
by pressing Power Key
Operation
“Power On” line Voltage OK? N
On? OK? (3.3V) Power
LED light Status with Remote controller with Tester B/D

- Stand-By: Red light or Turn Off


N Y
- Power on Condition: Turn Off

Check Power cord Replace Main B/D


was inserted properly Y
Measure voltage for each output of Power B/D

Voltage OK?
(3.5V)
inserted N
properly
OK? N
Y
Voltage OK? Replace Main B/D
Y ※ (12V,3.5V)

Check ST-BY 3.5V


Measure votage N
3.5V pin with Tester
Close <Power Pin Voltage Spec>
☞Page 6~7
Voltage
Output
Replace Power B/D Replace Power B/D Variable range
3.5V
3.325V~3.675V
(ST-BY)
12V 11.4~12.6V
-DC Power on: Switch on the TV with local key or remote controller
24V 21.6V~27V
-AC Power on: Switch on the TV with power supply(outlet)

2
Repair Method by Symptoms 3-2. No Power Check(check method)

<Check Power on (3.3V) and ST-BY(3.5V)> 1. Power Sequence : AC IN→ST-BY3.5V→P-ON→12V,24V→INV ON


2. ST-BY3.5V: Power Board → Main Board Micom IC/Power LED /IR Voltage
3. 24V: Power Board → Main Board Sound IC /LED Driver Voltage
Direct LED 4. 12V: Power Board → Main Board /Module Voltage
Power Board
Check the ST-BY(3.5V) and Power on(3.3V)

24 Pin (Power Board ↔ Main Board)


1 Power on(3.3V) 2 24V

3.3V 3 24V 4 24V

5 GND 6 GND

7 GND 8 GND

9 ST-BY (3.5V) 10 ST-BY (3.5V)

11 ST-BY (3.5V) 12 ST-BY (3.5V)


Edge LED 13 GND 14 GND
Power Board
15 GND 16 GND

17 12V 18 Inverter On/off

19 12V 20 Lamp : A-Dim


LED : N.C

21 12V 22 PWM Dim #1

23 N.C 24 Error-out
3.5V • Lamp SCANNING
Model: PWM Dim #2

The “LED” refers only to the type of lighting source used to illuminate the LCD pixels in the television
1. Direct LED: Direct type term refers to televisions that use a full panel of LEDs to illuminate the pixels.
2. Edge LED: Edge LED,means the LEDs that illuminate the pixels are located only on the edges of the set. 3
Repair Method by Symptoms 3-2. No Power Check(Check method)

24 Pin (Power Board ↔ Main Board)


`13 Model LA Series
<Check Power on (3.3V) and ST-BY(3.5V)> 1 Power on(3.3V) 2 Inverter
On/off(3.3V)

3 ST-BY(3.5V) 4 PWM Dim #1

5 ST-BY(3.5V) 6 PWM Dim #2


Direct LED
Power Board 7 GND 8 GND

9 24V 10 24V

11 GND 12 GND

13 12V 14 12V

15 12V 16 24V
3.3V 17 GND 18 GND

19 GND 20 GND

21 GND 22 L/DIMO_VS
Edge LED 23 L/DIM0_MOSI 24 L/DIM0_SCLK
Power Board 18 Pin (Power Board ↔ Main Board)

1 Power on(3.3V) 2 Inverter On/off

3 ST-BY(3.5V) 4 PWM Dim #1

5 ST-BY(3.5V) 6 PWM Dim #2

7 GND 8 GND

9 24V 10 24V
3.5V 11 GND 12 GND

13 12V 14 12V

15 12V 16 24V

17 GND 18 GND 4
Repair Method by Symptoms 3-3. No Power Check(Power Pin Description)

Pin No. Items Description of service and functions

24 ERROR The Inverter or HV signals whether the Lamp Turn-on functions normally
23 NC Null terminals

The CPU automatically adjusts the brightness, based on the wave pattern of
22 P-DIM
elements communicated (for each picture mode)

The CPU customizes the brightness of Lamp as to each different brightness of


20 A-DIM
picture (a serial current wave)

18 INV ON/OFF Signals for Inverter, controlled by MICOM


17,19,21 12V Power Supply to Main Board/Module
15,16 GND
13,14 GND
11,12 3.5V ST-BY
9,10 3.5V ST-BY
7,8 GND
5,6 GND
2,3,4 24V Sound IC B+ Voltage
1 Power On A Voltage required to turn Multi Voltages ON, Input by MICOM(Voltage: 3.3V)

5
Repair Method by Symptoms 4-1. No Picture Check(Flow Chart)

Case1. No Picture with audio working condition


Case2. No Picture with audio not working condition

First of all, Check whether all of cables between board are inserted properly or not.
(Main B/D↔ Power B/D, LVDS Cable, Speaker Cable, IR B/D Cable,,,)

☞Page 10~12
Sound Y Check Back Light Check Power Check
Back light Y Y
No Picture Working whether “On ”or off Board 12V, 3.5V Voltage Replace module
“On”
properly with naked eye line 12V, 3.5V
Case 1
N N N

Check Power Board 24v output Repair Power


No Picture with Sound Board or parts
not working conditon
Case 2
Y Replace Inverter
Voltage
or module
OK?

N End

Repair Power
Board or parts

☞Page 10~12 <Power Pin Voltage Spec>


Check Power Board Y Check and replace
Voltage Voltage
3.5V,12V,24 line MAIN B/D Output
OK? Variable range
3.5V
N End 3.325V~3.675V
(ST-BY)
Replace Power 12V 11.4~12.6V
Board 24V 21.6V~27V

6
Repair Method by Symptoms 4-2. No Picture Check(Check Power Pin)

Screen (LK, LW)

Check the DC 24V, 12V, 3.5V

24 Pin (Power Board ↔ Main Board) - 공통


1 Power on(3.3V) 2 24V

3 24V 4 24V

5 GND 6 GND
NC ERROR
12V P-DIM 7 GND 8 GND
12V A-DIM
9 ST-BY(3.5V) 10 ST-BY(3.5V)
12V INV-
GND ON 11 ST-BY(3.5V) 12 ST-BY(3.5V)
GND GND
3.5V GND 13 GND 14 GND
3.5V 3.5V
GND 3.5V 15 GND 16 GND
GND GND
17 12V 18 Inverter On/off
24V GND
ON/OFF 24V 19 12V 20 A-Dim
24V
<LW 21 12V 22 PWM Dim
Series>
23 N.C 24 Error-out
<LK Series>
(only Lamp
SCANNING Model
: PWM Dim #2)

7
Repair Method by Symptoms 4-2. No Picture Check(Check Power Pin)

Screen (LM)
<Check power On(3.3V) and DC 24V, 12V, 3.5V>
Direct LED Check the DC 24V, 12V, 3.5V
Power Board
24 Pin (Power Board ↔ Main Board) - 공통
1 Power on(3.3V) 2 24V

3 24V 4 24V

5 GND 6 GND

7 GND 8 GND

9 ST-BY(3.5V) 10 ST-BY(3.5V)

24V 11 ST-BY(3.5V) 12 ST-BY(3.5V)

13 GND 14 GND

15 GND 16 N.C
(Only LPB : V-sync)

17 12V 18 Inverter On/off

19 12V 20 N.C
(LPB, Lamp : A-dim)

21 12V 22 PWM Dim #1

23 N.C 24 Error-out
(only Lamp
SCANNING Model
: PWM Dim #2)

12V
3.5V
8
Repair Method by Symptoms 4-2. No Picture Check(Check Power Pin)

Screen (LA)
<Check power input voltage and DC 24V, 12V, 3.5V>

Check the DC 24V, 12V, 3.5V

Direct LED 24 Pin (Power Board ↔ Main Board) 18 Pin (Power Board ↔ Main Board)
Power Board
1 Power on 2 Inverter On/off 1 Power on 2 Inverter On/off

3 3.5V 4 PWM Dim #1 3 3.5V 4 PWM Dim #1

5 3.5V 6 PWM Dim #2 5 3.5V 6 PWM Dim #2

7 GND 8 GND 7 GND 8 GND

9 24V 10 24V 9 24V 10 24V

11 GND 12 GND 11 GND 12 GND

13 12V 14 12V 13 12V 14 12V

15 12V 16 24V 15 12V 16 24V

17 GND 18 GND 17 GND 18 GND

19 GND 20 GND

21 GND 22 L/DIMO_VS

23 L/DIM0_MOSI 24 L/DIM0_SCLK

9
Repair Method by Symptoms 4-3. No Picture Check(Check LED Driver 24V )

Check the DC 24V and Inverter on

Direct LED
P202 P203
Power Board

1~5 24V 1~5 12V

6~10 GND 6~10 GND

11 Error

12 Inverter ON( 3.3V)


Edge LED
Power Board
13 A-dim

14 P-dim

10
Repair Method by Symptoms 5-1. No Sount Check(Flow Chart)

<No Sound with Picture working condition>

☞Page 15~16
Check Check Y
Speaker N Check audio B+ 24V
No sound User menu  Voltage
Off of Power Board
speaker off (24V)

Y N

Cancel OFF Replace Power Board

Check Speaker N
Disconnection Replace main Board End
Cable
Disconnection

Replace Speaker

11
Repair Method by Symptoms 5-2. No Sount Check(Troubleshooting)

<No Sound/Picture OK > ‘13 LA Series


Main Board
Power Board
24 Pin (Power Board ↔ Main Board) ①
1 Power on 2 INV ON
3 3.5V 4 PDIM#1
5 3.5V 6 PDIM#2
② 7 GND 8 GND
9 24V 10 24V
11 GND 12 GND
13 12V 14 12V
15 12V 16 24V
17 GND 18 GND

Checking method(direction) when there is no sound

① Check the contact condition of or 24V connector of Main Board


② Measure the 24V input voltage supplied from Power Board
(If there is no input voltage, check the connector)

12
Repair Method by Symptoms 6. Picture Error Check(Flow Chart)

Vertical/Horizontal bar, residual image, light spot

6. Picture Error Board Check method

Replace
Module

☞ Page 31 N
Check color condition by input Check external
-External Input Screen Y Y Check and N
device Screen Screen
-Component OK? Good? replace Link Replace Main B/D
connection OK? OK?
-RGB Cable
condition
-HDMI/DVI Y
N N Y

Replace Request repair End End


☞Page 62 module for external
device
Check Test pattern

13
Repair Method by Symptoms 7-1. Sysmptoms List(Main Board)

Category Items Failure Cause Conditions

Main Picture Failure in I2C communication between


IC
B/D distortion MICOM and Main IC

Main Picture Picture occasionally cracked by the


IC soldering on Main IC
B/D distortion

Main Picture Picture cracking due to poor soldering on


IC Main IC
B/D distortion

Main Picture R-color noise caused by poor soldering


IC on Main IC
B/D distortion

14
Repair Method by Symptoms 7-1. Sysmptoms List(Main Board)

Category Items Failure Cause Conditions

Main Picture Mosaics generated from poor inside


IC
B/D distortion Main IC

Main Picture Picture cracking from poor service of an


IC element inside Main IC
B/D distortion

Main Screen frozen from a poor feature in Main


IC Static screen
B/D IC

Main
IC No sound No sound due to a poor feature in Audio IC
B/D

15
Repair Method by Symptoms 7-1. Sysmptoms List(Main Board)

Category Items Failure Cause Conditions

A “woong ~” sound from the right Speaker


Speaker Poor Noise in
caused by a speared damage in Sound
Cable processing sound
Cable

Speaker Poor Noise in A noise and vibration produced from influx


System processing sound of alien materials into Speaker System

Speaker Poor Noise in A noise and vibration produced from influx


System processing sound of alien materials into Speaker System

FFC Picture Picture cracking around the contour from


Poor contact
Cable cracking poor contact between FFC Cable PINs

16
Repair Method by Symptoms 7-2. Sysmptoms List(Module)

Category Items Failure Cause Conditions

Vertical bars caused by a irregular feature


Module Panel Vertical bars
in the Panel

Vertical bars caused by a irregular feature


Module Panel Vertical bars
in the Panel

Vertical bars caused by a irregular feature


Module Panel Vertical bars
in the Panel

Screen getting partially dark by a defect


Module Panel Dark screen
inside the Panel

17
Repair Method by Symptoms 7-2. Sysmptoms List(Module)

Category Items Failure Cause Conditions

Screen getting partially dark by a failure in


Module Driver B/D Dark screen MODULE DRIVER B/D

Vertical bars caused by a poor feature in


Module Panel Vertical bars
the Panel

1/3 part of Screen (left/center/right) getting


1/3 part of
dark due to a defective feature in Driver
Module Driver B/D Screen getting B/D
dark

Influx of alien materials into the Module


Module Panel Alien materials during the assembling process

18
Repair Method by Symptoms 7-2. Sysmptoms List(Module)

Category Items Failure Cause Conditions

Connector 1/2 of Picture Picture cracking from contamination by


Module
s cracking foreign materials inside a connector

Screen getting dark from a defect in LED


Module Panel Dark screen
unit inside the Panel

Vertical bars caused by a defective feature


Module Panel Vertical bars
in the Panel

Vertical bars caused by a defective feature


Module Panel Vertical bars
in the Panel

19
Repair Method by Symptoms 7-2. Sysmptoms List(Module)

Category Items Failure Cause Conditions

Screen partially Screen partially getting too bright from a


Module Panel too bright failure in LED inside the Panel

Alien materials
Module Panel Moisture inflow into the product
inside

Module Panel Film separation Film separation from defective processing

Processing
Processi Shipment With the Shipment setting inapplicable,
failure
ng failure setting failure Shipment is made only in a control mode

20
Repair Method by Symptoms 7-2. Sysmptoms List(Module)

Category Items Failure Cause Conditions

T-Con Vertical bars


EOS Damage in Electrical Over Stress
B/D evenly spaced

T-Con Vertical bars


EOS Damage in Electrical Over Stress
B/D evenly spaced

T-Con Picture
EOS Poor features in T-CON
B/D distortion

T-Con Picture Picture cracking from a poor feature in


IC
B/D distortion T-CON IC

21
Repair Method by Symptoms 7-2. Sysmptoms List(Module)

Category Items Failure Cause Conditions

T-Con Picture Picture cracking from a poor feature in 3D


IC
B/D distortion Formatter IC

T-Con Picture Picture cracking from contamination


IC
B/D distortion around 3D Formatter IC

T-Con Picture Picture cracking from an error in Boot


IC Data
B/D distortion

T-Con Picture Picture cracking from an error in Boot


IC Data
B/D distortion

22
Repair Method by Symptoms 7-2. Sysmptoms List(Module)

Category Items Failure Cause Conditions

T-Con Picture Picture cracking due to desquamation of


IC
B/D distortion FRC IC

T-Con Picture Picture cracking due to desquamation of


IC
B/D distortion FRC IC

23
Repair Method by Symptoms 7-3. Sysmptoms List(LVDS Cable)

Category Items Failure Cause Conditions

LVDS Poor Picture Picture cracking along the contour from


Cable contact distortion poor contact between LVDS Cable PINs

LVDS Poor Picture Picture cracking from poor contact


Cable contact distortion between LVDS Cable PINs

LVDS Poor Picture Picture cracking along the contour from


Cable contact distortion poor contact between LVDS Cable PINs

24
Repair Method by Symptoms 7-3. Sysmptoms List(FFC Cable, Cabinet, etc)

Category Items Failure Cause Conditions

Picture cracking along the contour


FFC Poor Picture
caused by poor contact between FFC
Cable contact distortion
Cable Pins

Processi Processing Shipment With the Shipment setting inapplicable,


ng failure failure setting failure Shipment is made only in a control mode

Desquamation Some space made Inside from tear-off of


Cabinet ICM Filter
of ICM Filter ICM Filter caused by a external shock

Vibration and
Speakers shaking from some damage in
Cabinet Damage noise in
the Cabinet Speaker Boss
Speaker System

25
Repair Method by Parts 8. Main Board Check (Symptoms)

Mosaic Patterns Picture Distortion

Picture Smear

26
Repair Method by Parts 8. Main Board Check (One-Point Repair)

1. Symptoms : Screen color smearing intermittently


2. Cause of failure : Link cable contact fault

<Check Point> <Repiar method>


1. Check RGB pattern with ‘ADJ Key through SVC Remote

2. Link cable by gently tapping the contact area on the


symptoms of hand Checked

3. Link cable disassembly and re-assemble

4. Check whether the screen display is normal.

Color smearing

27
Repair Method by Parts 8. Main Board Check (One-Point Repair)

1. Symptoms : Auto Power On/Off


2. Cause of failure : Main board failure

<Check Point> <Repiar method>

1.Press Button ‘In-Start Mode’ Key 1.If there are “POWER_OFF_BY_NO_ POLLING” message
2.Enter ‘Power Off Status’
2. Replace the main board

3. Check the condition of Screen

*POWER_OFF_BY_NO_POLLING
:If there are no communications between micom and Host
CPU for 15second
→ Micom will reboot all system

28
Repair Method by Parts 9. Module Check(One Point Repair)

1.Title: No Display (Only BackLight or multiple vertical bars)


- Sound Normal/CH Volume Control Normally * P-VCC: A standard voltage to activate the LCD
VCC: Usually 3.3V power required to activate Digital IC
2. Applied to: LK, LW57, and 65 VDD: A voltage supplied to Source Drive IC for activation of
LCD
3. Troubleshooting: As shown below, inspect the P-VCC(12V) B/D inside T-CON VGL/VGH: Voltages required to turn TFT Gate on/off
-VGL: TFT Gate on
and US1 output voltage. -VGH: TFT Gate off

Upon an abnormal voltage, open and re-check the FFC leading from T-CON to the Module.
Upon recurrence of a same failure, change T-CON or the Module if the voltage is normal.
(Refer to below Normal Voltage)
T-Con Board P VCC

VDD
VCC

VGL

VGH

PANEL VCC : F1 or C1(12V) VCC : C215 (3.3V) VGL : C251 (-6V)


VDD : C239 (16V) VGH : R271 (28V)

A failure condition Output voltage of US1

29
Repair Method by Parts 9. Module Check(One Point Repair)

1.Title: No Display (Only BackLight)


* P-VCC: A standard voltage to activate the LCD
- Sound Normal/CH Volume Control Normally VCC: Usually 3.3V power required to activate Digital IC
VDD: A voltage supplied to Source Drive IC for activation of LCD
2.Applied to: LW9500, LW9600, andLW9800 VGL/VGH: Voltages required to turn TFT Gate on/off
-VGL: TFT Gate on
3. Troubleshooting: -VGH:TFT Gate off

Check if Back Light is ON and, if it’s ON, re-check T-CON as the following sequence.
Change the Module if the voltage is normal. Change T-CON if voltage abnormal.

T-Con Board T-Con Board

P701 VDD
VCC
P VCC

VGH VG
L

No picture (Only backlight) VCC : D403 (3.3 V) VDD : D402 (16V)


P VCC : P701 48~51 PIN (12V)
VGH : D400 (27V) VGL : C450 (-5V)

A failure condition Input voltage of LVDS Output voltage of IC 401 output

30
Repair Method by Parts 10-1. Wi-Fi Check(Flow Chart)

Wi-Fi operating error 9. Wi-Fi Operating Checking(Flow Chart)


☞Page 34

Check the Wi-Fi Mac value Check the Wifi wafer Normal
N N Replace
is “NG”? Voltage
INSTART menu Pin no.1 Main B/D
3.3V

Y Y

Check & Repair


Wifi cable
Close
connection

Pin map
Wi-Fi Mac value N
is “NG”? Close
PIN USB interface

Y 1 Vcc(3.3V)

Change the Wifi 2 DM


assy
3 DP

4 GND

5 WOW

6 NC

31
Repair Method by Parts 10-2. Wi-Fi Check(One Point Repair)

1. Symptoms : Wi-Fi disconnection


2. Cause of failure : Caused by bad Wi-Fi Module

<Check Point> <Repiar method>

1. Check the Wi-Fi Version at INSTART menu 1. Wi-Fi Module replacement


- Wi-Fi MAC and IP Address to check an abnormal 2. Check the wi-fi Version at INSTART menu
Inspection - Wi-Fi MAC and IP Address normal check
connections from main to Wi-Fi module

32
Repair Method by Parts 11. Camera Check(Flow Chart/Troubleshooting)

10. Camera Operating Checking(Flow Chart)


Camera Operating Error

Check the Camera wafer Check


Check the Camera Ver. N N Replace
Voltage
INSTART menu is “NG”? P4200 (pin no.2) Main B/D
(3.3V)

Y Y

Check & Repair Close


Camera cable
connection

Camera Ver. N
Close
is “NG”?

Change the
Camera assy

33
Repair Method by Parts 12-1. Magic Remote Check(Flow Chart)

Check the RF Receiver ver N Check Is it shown ‘ok’ N Turn off/on the
Normal Y Press the
INSTART menu is “00.00”? M-Remote Operating? ‘wheel’ message? set
itself Operation

N Y Press the
Y wheel
Close
Check & Replace
Batterry of
Check RF assy
N Replace M-Remote
connection
RF assy Cable
☞Page 50
Press the ‘back’
N
Y and ‘home’ key Is it shown ‘ok’
Y at the same time message?
Normal
Down load the Firmware Operating? Close about 5sec
Close
* INSTART MENU15.RF Y
Remocon Test3. Firmware
N
download
Close
Replace M4
Close

34
Repair Method by Parts 12-2. Magic Remote Check(Pairing/Un Pairing)

RF Pairing/Un-Pairing Method

Method Description

▶When pairing, the remote should make a pairing


request IR signal to TV.
1. Method 1 ▶When TV receive the IR signal, it should send “
- If un-paired, just press "OK"button. pairing request packed" to the RF receiver.
RF Pairing - If paired, press "OK" button after un-pairing. ▶ After pairing success, the remote LED should
2. Method 2(Repairing) blink for some time and TV sends "pairing
- Press "BACK"button for 5 sec. success pack" back to TV.
▶When remote try's to un-pair, it doesn't care
about state of receiver(stand alone).

▶When remote try's to un-pair, it doesn't care about


Depending on Magic remote state of receiver(stand alone).
Press "HOME/SMART" button and "BACK" ▶After un-pairing, all pairing information should be
RF
button at the same time for 5sec. erased.
Un-Pairing R/C LED blinks 3times after a few sec's. ▶After un-pairing, LED should blink 3times.
Then un-paired. To re-pair Press OK button. ▶The remote just becomes active only in IR mode
control function.

35
Repair Method by Parts 12-3. Magic Remote Check(Register/Unregister)

To Register Magic Remote


‘13 models -Back/Smart keys

Press the Wheel(OK) button on the remote control

Pop-up message will appear on screen

When Registration completes, another pop-up message will appear.

To bring up cursor, simply move remote around.


Maximum communication distance:10m or 32.8ft

Unregister Magic Remote Control

• Press the “Home” and “Back” on the


remote fo 5 seconds
M4 Remote MR13P Remote
• The Red LED at the top of the Remote will
blink 3time
• To re-register the Remote, follow first
procedure
36
Repair Method by Parts 13. Remote Control Check(Flow Chart)

Remote control(R/C) operating error

Replace
Main B/D
☞Page 52~55 ☞Page 52~55 ☞Page 52~55
Check R/C itself Y Check & Repair N Y Y
Operating Check B+ 3.5V Check IR Normal
Operation Cable connection Operating Voltage
OK? On Main B/D Output signal Signal?
Connector solder OK? OK?
N
Y N N
☞Page 10~12
Check R/C Operating Check & Replace Close Check 3.5v on Power B/D
When turn off light Baterry of R/C Replace Power B/D or
in room Replace Main B/D Repair/Replace
(Power B/D don’t have problem) IR B/D

Y
If R/C operate, Close
Operating
Explain the customer OK?
cause is interference
from light in room. N

Replace R/C

37
Repair Method by Parts 13-2. Remote Control Check(Troubleshooting)

Main Board
P4101
1 GND
2 KEY1
3 KEY2
③ 4 +3.5V_ST
5 GND
6 LOGO/LED_R
④ 7 IR
8 GND

1.2. Check IR cable condition between IR & Main board.


3. Check the st-by 3.5V on the pin no.4
4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog Tester needle
moves slowly, and defective when it does not move at all.

38
Repair Method by Parts 13-2. Remote Control Check(Troubleshooting)

<LM Series>
P4800
Main Board
③ 1 3.3V
2 GND
3 RX
4 TX
5 RESET
6 DC
7 DD
8 GND

Checking order
1, 2. Check Motion cable condition between Motion assy & Main board.
3. Check the 3.3V on the pin no. 1.

39
Repair Method by Parts 13-2. Remote Control Check(Troubleshooting)

<LA Series>
P4002
Main Board 1 GND
2 KEY1
3 KEY2
③ 4 +3.5V_ST
5 GND
6 LED
7 +3.5V_ST
8 GND


Checking order
1, 2. Check IR cable condition between IR & Main board.
3. Check the st-by 3.5V on the pin no 4,7.
4. When checking the Pre-Amp when the power is in ON condition, it is normal when the Analog
Tester needle moves slowly, and defective when it does not move at all.

40
Adjustments method after Repair 16. Tool option setting method after main B/D change
(adjustment RGB Pattern)

Error symptom Content


Video Error Color error Adjustment Test pattern - ADJ Key

You can view 6 types of patterns using the ADJ Key

Checking item: 1. Defective pixel


2. Residual image
3. MODULE error (ADD-BAR, SCAN BAR)
4. Video error (Classification of MODULE or Main-B/D!)
41
Adjustments method after Repair 17. Software Upgrad method with USB Memory

Step 1. Check full model name of your TV(Select one) Step 2. Upgrade TV
a. Check a label on TV(Side or Rear) a. Make a folder “LG_DTV” on USB drive
b. Save the software in “LG_DTV” folder. Make sure file is unzipped before placing in Folder
c. Insert USB memory drive into USB port on TV

b. Check menu(Non-Smart TV model)


- Press(MENU) key on remot
- Press((Red) “Customer Support” key on remote
- Select “Produce/Service Info” d. Select “Start” if “TV Software Upgrade” Pop-up appears
- Check “Model/Type” e. Save the software in “LG_DTV” folder. Make sure file is unzipped before placing in Folder
f. Insert USB memory drive into USB port on TV

Note)
If current software on TV is same with or newer than
That on USB drive, TV software Upgrade menu won’t be opend
(Some USB memory devices may not be compatible with TV)

b. Check SETUP(Smart TV model)


- Press(Home) key on remot
- Select “SETUP”
Please wait while the update is copied to TV
- Move to “SUPPORT”
※ Don’t remove USB drive while this message is displayed
- Select “Product/Service info”
- Check “Model/Type” ※ Don’t unplug TV power cord while this message is displayed

Software upgrade in on progress


※ Don’t unplug TV power cord while this message is displayed

After the upgrade is completed, this message is displayed


TV will restart automatically in 5 sec, than TV is ready to use
42
Course title LCD TV Repair Guide Handbook

Category
□ Leadership □ Marketing □ Sales ■ CS
□ Manufacturing □ Quality □ Biz. administration

Published on 04/01/2014

Developed by HE CS Technology Support Team

Published by Yongsu kim(e-mail: yongsu1.kim@lge.com)

Updated on 11/02/2014

※ No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical,
including photocopying, recording, or by any information storage or retrieval system without written permission from LGE.

S-ar putea să vă placă și