Documente Academic
Documente Profesional
Documente Cultură
• The fabricated penstocks are tested for 1.5 times the design pressure.
Radiographic and ultrasonic testing are done for detecting defects in the
welded joints.
• Gate is provided u/s of the Penstock and d/s of the gate air vent or stand pipe
is provided, which connects the top of the Penstock to the open air. Air vent
pipe facilitate proper escape of air from the Penstock while filling the
Penstocks.
• Manholes are provided along the length of the Penstock at 120 m to 150 m to
provide access to the pipe interior for inspection maintenance and repair.
• The radius of curvature in the Penstock profile should be three to five times
the diameter of the Penstock.
QUALITY OF APPROACH FLOW TO TURBINES
• Flow free of separations.
• Deviation of local velocity from the average velocity should not be greater
than ± 5%.
• Deviation of local flow direction from axial should not be more than 50.
Advantages:
• Easy and regular inspection
Disadvantages:
• Prone to rusting and corrosion being exposed
• Nagarjunasagar dam: embedded and supported on the d/s slope of the dam
• Jawaharsagar dam: Partly embedded in the dam and partly encased in concrete
and buried in earth.
• Installation costly
Conduits are placed in open tunnel duly supported suitably as surface penstock
or backfilled with concrete. The Penstocks are also laid in concrete diversion
tunnel converted into Penstock tunnel and backfilled with concrete as at Pong
Dam.
Penstocks is laid in pressure shaft or tunnel shaft and backfilled with concrete.
In this arrangement rock participation is taken into account. So, thickness
requirement is less.
(B) Based on Method of Fabrication
(iii) Multilayer Penstock – several layers of thin steel plates wrapped around the
pre-fabricated central core pipe.
(iv) Banded or Hooped Penstocks – bands or hoops are slipped over thin walled
penstock pipe which induce pre-stress in the pipe
(i) Steel Penstocks – used for head > 50 m, welded pipe is invariably used.
Alignment:
Grade:
Empirical Formulae
D = Diameter in (m); H = rated head of Turbines in (m); P = rated horse Power (metric)
Q = discharge (m3/s)
2. USBR (1958)
4. G. Isakssons Formula
D = Q0.40 for steel lined shafts at depths from 30 to 80 m
D(m); Q(m3/s)
5. F. Fahlbush’s Formula
D = 0.62 Q0.48 for concrete lined conduits
econ_dia_Penst1.xls
Graphical Solutions
Total → C=
C1+C2
Cost
C2 C1
Diameter
Economical diameter
Analytical Methods
Notations used:
Cc = Unit cost of concrete lining Rs/m3
D = Diameter
η = Efficiency of plant
N = Manning's Coefficient
Q = Discharge
If C1 = k1 Dm and C 2 = k 2D n
mk1Dm-1 + nk2Dn-1 = 0
Annual Cost of Energy Lost, C1
Head Loss
k1 = 0.7102×104fQ3 ηLf Cp
Mass of steel,
Thus,
econ_dia_Penst2.xls
I.S. METHOD (IS 11625 – 1986)
= 1.39 D2 Ce
= 0.6 D2 Cc
Thickness of pipe
σa = allowable stress
Volume of steel per unit length in n conduits
Head Loss
(B) If head loss is kept constant
as
as Q = n Qn
As t ∝ diameter
Volume of steel per unit length in n conduits
Design Criteria for Penstocks
Non-embedded Penstocks
According to the ASME Code, a penstock may be designed under the following
conditions.
(i) Normal conditions – maximum static head plus pressure rise due to normal
operation
Allowable stress = ultimate tensile strength /3 (3)
< 2/3 (0.5) Minimum yield stress
(ii) Intermittent condition – conditions during filling & draining the penstock
Allowable stress = Ultimate tensile strength / 2.25 (2.5)
< 0.8 (2/3) Minimum yield stress
(ii) Intermittent condition – conditions during filling & draining the penstock
Allowable stress = 0.4 Ultimate tensile strength
< 2/3 Minimum yield stress
1. ASME Code
Subject to minimum
When the trash rack consists of a rack of bars, the loss will depend on bar
thickness, depth and spacing
where max. loss values are desired, 50% of the rack area shall be considered
clogged
(2) Head Loss at Intake Entrance
depends on shape of the intake mouth
V = Velocity at entrance
ke = Loss coefficient for entrance and read from following table (IS:4880
(PartIII) – 1976)
(3) Friction Loss
Darcy-Weisbach formula:
Manning’s Formula:
Expansion
Contraction
The water level in the Forebay of the proposed Hanuman Ganga small hydro project is 2345.55
m and normal tail water level is 2186.20 m, calculate the available net head using the following
data:
Va = 0.65 m/s
L = 380 m
D = 1.117 m
f = 0.015
Velocity in penstock,
h Air vent
h(m); d(m); and V(m/s)
V
Purposes
(i) To admit air when gate is closed and the water in the conduit recedes
down.
(ii) To exhaust air when the penstock is being filled through bye pass lines to
balance the water pressure on two sides of the gate prior to its being lifted
up.
(iii) To control sub-pressures downstream of gate at partial opening
As per IS 9761:1981 – the air vent shall be so designed as to admit air at the
rate the turbine is discharging water under full gate conditions (Qa = Q)
The area of air vent may be fixed by the following formula (IS: 9761:1981)
E = Young’s modulus
D = Penstock diameter
I = Moment of Inertia =
A turbine develops a maximum of 5000 h.p under a head of 25 m at an overall efficiency of 80%.
Find the size of an air vent to be provided just behind the gate. Safe difference of pressure between
the inside and outside of the pipe = 0.15 kg/cm2 and Cd=0.7.
Given:
= 373000/9810×9.81×0.80×25 = 19.0
m3/s
Qa = Q = 19 m3/s (as per IS 9761:1981)
Diameter, d = 0.47 m
IS: 9761:1981
END OF CHAPTER