Documente Academic
Documente Profesional
Documente Cultură
Permeability
(Das, chapter 7)
1
Soil Permeability- Definition
2
Soil Permeability -Definition
water
3
What is Permeability?
Permeability is the measure of the soil’s ability to permit water to
flow through its pores or voids
water
5
Importance of Permeability
The following applications illustrate the importance of permeability
in geotechnical design:
The design of earth dams is very much based upon the
permeability of the soils used.
The stability of slopes and retaining structures can be greatly
7
Importance of Permeability
8
Why does water flow?
If flow is from A to B, the energy is higher at A
than at B.
Energy is dissipated in
overcoming the soil water
resistance and hence is the
head loss.
A B
9
Bernoulli’s Equation
- due to pressure
datum
3. Kinetic energy
- due to velocity
10
Bernoulli’s Equation
Then at any point in the fluid, the total energy is equal to
At any point
u
hZ
w
H1 H 2
i
X
14
Hydraulic Gradient
W.T.
A Impervious Soil
h = hA - hB
W.T.
L
hA = total head
B
Impervious Soil
hB= total head
Datum
(hA hB ) h
i
L L
W.T.
Impervious Soil
)h = hA - hB
W.T.
Water In hA
Impervious Soil
Datum
hB
Head Loss or
Head Difference
or Energy Loss
h =hA - hB
i = Hydraulic Gradient
hA
(q)
Water
out
hB
ZA ZB
Datum
Darcy’s Law:
v= k.i
Where:
v = discharge velocity which is the quantity of water flowing in
unit time through a unit gross cross-sectional area of soil at
right angles to the direction of flow.
k = hydraulic conductivity (has units of L/T)
i = hydraulic gradient = h/L
Then the quantity of water flowing through the soil per unit time is
Discharge = Q = v. A = k (h/L). A
Flow in Soil
W.T.
A Impervious Soil
h = hA - hB
W.T.
L
hA = total head
B
Impervious Soil
hB= total head
Datum
(hA hB ) h h
i Q k i Ak A
L L L
To determine the quantity of flow, two parameters are needed
i can be determined
1- from the head loss and geometry
2- flow net (chapter 8)
Hydraulic Conductivity
• The hydraulic conductivity k is a measure of how easy
the water can flow through the soil.
• The hydraulic conductivity is expressed in the units of
velocity (such as cm/sec and m/sec).
21
Hydraulic Conductivity
22
Hydraulic Conductivity, k
Typical Values
23
Laboratory Testing of Hydraulic Conductivity
Two standard laboratory tests are used to determine
the hydraulic conductivity of soil
24
Constant Head Test
• The constant head test is used primarily for coarse-grained soils.
• This test is based on the assumption of laminar flow (Darcy’s Law
apply)
From Darcy’s Law
h
Q k i At k At
L
Where:
Q = volume of water collection
A = cross section area of soil specimen
T = duration of water collection
V L
k
h At
Then compute:
25
Constant Head Test
26
Constant Head Test
27
Constant Head Test
28
Falling Head Test
• The falling head test is mainly for fine-grained soils.
a = cross sectional
area of standpipe
Simplified Procedure:
29
Falling Head Test
Calculations:
aL h1 a = cross sectional
k ln area of standpipe
At h2
Where:
A = cross sectional area of the soil
a = cross sectional area of the standpipe
h1 = distance to bottom of the beaker
before the test A = cross
h2= distance to bottom of the beaker after sectional L
the test area of soil
L = length of the sample
t = t2-t1
Then compute:
30
Falling Head Test
Calculations:
aL h1
k ln
At h2
The above equation is derived assuming:
31
Falling Head Test
Derivation of Falling Head equation
Examples
• Horizontal flow
• Constant hydraulic
gradient conditions
• Analogous to resistors in
series
Equivalent Hydraulic Conductivity on Stratified Soils
• Vertical flow
• Constant velocity
• Analogous to resistors in
parallel
Examples
2. Borehole test.
3. Packer Test.
Permeability Tests using Pumping Wells
OR
r2
q . ln
r1
k
(h22 h12 )
If q, h1, h2, r1, r2 are
known , k can be
calculated
Pumping Well with Observation holes
Pumping Well in a Confined Aquifer
q
r2
log 10
q r1
k
2.727 H (h2 h1 )
If q, h1, h2, r1, r2 are
known , k can be
calculated