Documente Academic
Documente Profesional
Documente Cultură
Soil Stabilization
The soil stabilization means the improvement of stability or bearing power of the soil by the use of controlled compaction, proportioning and/or the addition of suitable admixture or stabilizers.
Financial Resources to Provide a complete network Road System to build in conventional method Effective utilization of locally available soils and other suitable stabilizing agents. Encouraging the use of Industrial Wastages in building low cost construction of roads.
Mechanical Stabilization Soil Cement Stabilization Soil Lime Stabilization Soil Bitumen Stabilization Lime Fly ash Stabilization Lime Fly ash Bound Macadam.
Mechanical Stabilization
This method is suitable for low volume roads i.e. Village roads in low rainfall areas. This method involves the correctly proportioning of aggregates and soil, adequately compacted to get mechanically stable layer The Basic Principles of Mechanical Stabilization are Correct Proportioning and Effective Compaction
Mechanical Strength of aggregates Gradation Properties of the Soil Presence of Salts Compaction
Mechanical Strength
When the soil is used in small proportion to fill up the voids the crushing strength of aggregates is important
Gradation
A well graded aggregate soil mix results in a mix with high dry density and stability values
Properties of soil
A mix with Plasticity Index, results poor stability under soaking conditions. Hence it is desirable to limit the plasticity index of the soil
Presence of Chemicals
Presence of Salts like Sulphates and mica are undesirable Presence of Calcium Chloride is Beneficial
Compaction
Effective Compaction is desirable to produce high density and stability mix
Soil
THE PHYSICAL PROPERTIES Particle Size Distribution Clay content Specific Surface Liquid limit and Plasticity Index
Cement
A increase in cement content generally causes increase in strength and durability
Compaction
By increasing the amount of compaction dry density of the mix, strength and durability also increases
Curing
Adequate Moisture content is to be retained in order to accelerate the strength
Additives
There are some additives to improve properties Lime Sodium hydroxide Sodium Carbonate Calcium Chloride
Soil Cement specimens are prepared with various cement contents in constant volumes moulds The compressive strength of these specimens tested after 7 days of curing A graph is plotted Cement content Vs compressive strength The Cement Content Corresponding to a strength of 17.5 kg/cm2 is taken as design cement content
Type of Lime
After long curing periods all types of limes produce same effects. However quick lime has been found more effective than hydrated lime Calcium Carbonate must be heated at higher temperature to form Quick lime calcium oxide( CaO) Calcium oxide must be slaked ( by the addition of water) to form Hydrated lime
Compaction
Curing
The strength of soil-lime increases with curing period upto several years. The rate of increase is rapid during initial period The humidity of the surroundings also affects the strength
Additives
Sodium metasilicate, Sodium hydroxide and Sodium Sulphate are also found useful additives
The particle size, shape and gradation of the soil influence the properties of the soil-bitumen mix.
Types of Bitumen
Cutbacks of higher grade should be preferred Emulsions generally gives slightly inferior results than Cutback.
Amount of Mixing
Increasing proportion of bitumen causes a decrease in dry density but increases the stability after a certain bitumen content The optimum bitumen content for maximum stability generally ranges from 4 to 6%
Mixing
Improved type of mixing with low mixing period may be preferred
Compaction Effective Compaction results higher stability and resistance to absorb water Additives Anti stripping and reactive chemical additives have been tried to improve the properties of the mixes Portland cement can also be used along with the soil bitumen
Necessity
Scarcity of good quality aggregates / soil for road construction Production and accumulation of different waste materials Disposal and environmental problem Economical and gainful utilisation
Quality of waste is not controlled by their manufacturers Characteristics of by-products vary in a wide range Road construction practice is accustomed to traditional materials of steady quality Specifications of layers compaction of traditional materials are not suitable for waste materials
Amount of yearly produced waste material should reach a certain lower limit The hauling distance should be acceptable The material should not have a poissonous effect The material should be insoluble in water The utilisation should not have a pollutional effect to the environment
Free from organic matter Should not swell or decay as influenced by water Should not be soluble in water Particles should be moderately porous
Industrial wastes
Steel Plants
* * *
generation Indian scenario - Use of coal with high ash content - Negligible utilisation of ash produced Bulk utilisation - Civil engineering applications like construction of roads & embankments
s Embankments and backfills s Stabilisation of subgrade and sub-base s Rigid and semi-rigid pavements
s s s s
Fly ash properties vary widely, to be characterised before use Major constituents - oxides of silica, aluminum, iron, calcium & magnesium Environmentally safe material for road construction Possesses many favourable properties for embankment & road construction
Light weight, lesser pressure on sub-soil High shear strength Coarser ashes have high CBR value Pozzolanic nature, additional strength due to self-hardening Amenable to stabilisation Ease of compaction High permeability Non plastic Faster rate of consolidation and low compressibility Can be compacted using vibratory or static roller
Range 1.90 2.55 Non plastic 0.9 1.6 38.0 18.0 Negligible 30 0 40 0 1.75 x 10 -5 2.01 x 10 -3 0.05 0.4 8 x 10 -6 7 x 10 -4
Coefficient of uniformity
3.1 10.7
3 to 4 per cent 5 to 8 per cent 10 times or more in comparison to source coal Higher
Ideally suited as backfill material for urban/ industrial areas and areas with weak sub soils Higher shear strength leads to greater stability Design is similar to earth embankments Intermediate soil layers for ease of construction and to provide confinement Side slope erosion needs to be controlled by providing soil cover Can be compacted under inclement weather conditions 15 to 20 per cent savings in construction cost depending on lead distance
Fly ash - better backfill material for reinforced embankments Polymeric reinforcing materials Geogrids, friction ties, geotextiles Construction sequence similar to reinforced earth structures
7.8 to 5.9 m
Laying of geogrids
Geogrid reinforced fly ash approach embankment Length of embankment 138.4 m Height varied from 3.42 m to 1.0 m Opened to traffic in 1997
Stabilised
Mixing with soil reduces plasticity characteristics of subgrade Addition of small percentage of lime or cement greatly improves strength Leaching of lime is inhibited and durability improves due to addition of fly ash Pond ash & bottom ash can also be stabilised Lime-fly ash mixture is better alternative to moorum for construction of WBM / WMM
Construction of semi-rigid/ rigid pavements Lime-fly ash concrete Dry lean cement fly ash concrete Roller compacted concrete Fly ash admixed concrete pavements Lime-fly ash bound macadam Precast block paving High performance concrete
Bituminous concrete 40 mm 100 mm DBM BM 75 mm WBM Gr III/WMM 75 mm WBM Gr II/WMM 150 mm GSB 350 mm
Bituminous concrete 40 mm DBM 100 mm BM 75 mm WBM Gr III/WMM 75 mm Fly ash + stabilised 6% cement layer 150 mm
Fly ash admixed PQC 300 mm DLFC 100 mm Pond ash 300 mm
Total length of the road 1 km Five sections of 200 m each with different pavement sections Pond ash has been used for replacing moorum in sub-base course Stabilised pond ash used for replacing part of WBM layer One rigid pavement section using DLFC and RCCP technology was laid Performance of all the specifications is good
fly ash
A rural road near Dadri in District Gautam Budh Nagar, Uttar Pradesh was selected Total length of road 1.4 km Bottom ash used as embankment fill Base course constructed using fly ash stabilised with 8% cement RCCP Wearing course 10 cm thickness RCCP Mix proportion 1:2:4 30 per cent of cement and 20 per cent of sand replaced with fly ash in RCCP Shoulders 8% cement stabilised fly ash
Demonstration road project using fly ash near Dadri (U.P) Typical section
RCCP wearing course - 0.1 m Stabilised fly ash base - 0.1 m Soil cover Bottom ash Stabilised fly ash Shoulder
Compaction of RCCP
Published recently by Indian Roads Congress (SP- 58:2001) Includes design aspects also Handling and construction Loose layer thickness of 400 mm can be adopted if vibratory rollers are used Moisture content - OMC + 2 per cent Use of vibratory rollers advocated Minimum dry density to be achieved - 95 per cent of modified Proctor density Ash layer and side soil cover to be constructed simultaneously
Total production of slag from steel industries is about 8.0 million tonnes Types of slags
Steel slag
2.78 2.82 2.82 3.33 2.97 2.99 2.67 1.53 1.72 0.58 1.38 0.74 1.29 0.48
2% Max
Los Angeles 18.80 abrasion value (%) Impact value 15.79 (%) Soundness value (%) Percentage voids 1.66
25.00
14.28
34.00
40% Max
14.80 1.17
16.90 0.33
24.50 0.17
46.40
43.90
43.10
43.80
Steel slags
Obtained as a waste product during production of steel Particle size varies from 80 mm to 300 microns Compared to blast furnace slag, steel slag contains lower amount of silica, higher amounts of iron oxide and calcium oxide Due to presence of free lime, steel slag should be weathered before using it in construction
Processed municipal wastes utilised for construction of test track on village road near Delhi Stabilised municipal waste used for construction of sub-base layer Performance of stretch is good
Kimberlite tailings
Kimberlite tailings are waste produced from diamond mining Can be used in base or sub-base course by adopting mechanical or cement stabilisation High value of water absorption makes them unsuitable for use in bituminous pavement
THANK YOU