Documente Academic
Documente Profesional
Documente Cultură
Curs 3
Selectarea entitilor
Metode de selectare: -Verb/Substantiv selecie standard -Substantiv/Verb selecie nainte de editare
Select objects:
W Window C Crossing ALL All P Previous R Remove A Add L Last CP CPoligon
F Fence
U Undo
WP Wpoligon
G Group (set creat cu C-da GROUP)
Command: erase Select objects: c Specify first corner: Specify opposite corner: 2 found Select objects:
Fereastr Crossing
Crossing
Window
Fence
Modificri geometrice
Comanda
TRIM
Meniul derulant: Modify >Trim
TRIM
Command: trim Current settings: Projection=UCS, Edge=Extend Select cutting edges ... Select objects: 1 found (s-a selectat linia frontier n S1) Select objects: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]: Select object to trim or shift-select to extend or [Project/Edge/Undo]:
nainte
Dup
Modificri geometrice
Comanda
EXTEND
Meniul derulant: Modify >Extend
EXTEND
Dialog
Command: extend Current settings: Projection=UCS, Edge=Extend Select boundary edges ...(se selecteaz entitatea frontier n S1) Select objects: 1 found Select objects: (ncheie selecia)
Se selecteaz Select object to extend or shift-select to trim or [Project/Edge/Undo]: entitile de Select object to extend or shift-select to trim or [Project/Edge/Undo]: extins n S2 i Select object to extend or shift-select to trim or [Project/Edge/Undo]: S3, sau cu opiunea de selectare S2 Fence
S3
S1
nainte Dup
Modificri geometrice
Comanda
BREAK
Meniul derulant: Modify >Break
BREAK
Dialog
Ex. 1. ntrerupere ntre dou puncte
Command: break Select object: (se selecteaz n S1) Specify second break point or [First point]: (se selecteaz n S2)
S1
S2
Dup
By Dr. ing. Ioan Lihtechi
nainte
Opiunea F (precizare cu exactitate a primului punct) Command: break Select object: (se selecteaz n S1) Specify second break point or [First point]: f Specify first break point: cen of (se indic P1) Specify second break point: cen of (se indic P2)
S1 P1 P2
Dup
By Dr. ing. Ioan Lihtechi
nainte
Opiunea F ( ntrerupere ntr-un singur punct) Command: break Select object: (se selecteaz n S1) Specify second break point or [First point]: f Specify first break point: int of (se indic P1) Specify second break point: @ (echivalent cu @0,0)
nainte
Comenzi de editare
Comanda
FILLET
Meniul derulant: Modify > Fillet
FILLET
Dialog: Command: fillet Current settings: Mode = TRIM, Radius = 0.00 Select first object or [Polyline/Radius/Trim]: r Specify fillet radius <0.00>: 10 Select first object or [Polyline/Radius/Trim]: (se selecteaz n S1) Select second object: (se selecteaz n S2) Command:
S1
S2
nainte
Dup
By Dr. ing. Ioan Lihtechi
Opiunea P Command: fillet Current settings: Mode = TRIM, Radius = 10.00 Select first object or [Polyline/Radius/Trim]: r Specify fillet radius <10.00>: 7 Select first object or [Polyline/Radius/Trim]: p Select 2D polyline: (se selecteaz n S1) 4 lines were filleted Command:
S1
nainte
Dup
By Dr. ing. Ioan Lihtechi
Comenzi de editare
Comanda
CHAMFER
Meniul derulant: Modify > Chamfer
CHAMFER
Dialog: Command: chamfer (TRIM mode) Current chamfer Dist1 = 0.00, Dist2 = 0.00 Select first line or [Polyline/Distance/Angle/Trim/Method]: d Specify first chamfer distance <0.00>: 22 Specify second chamfer distance <22.00>: 10 Select first line or [Polyline/Distance/Angle/Trim/Method]: (selectare
n S1)
S1 S2
nainte
Dup
Opiunea A Command: chamfer (TRIM mode) Current chamfer Dist1 = 22.00, Dist2 = 10.00 Select first line or [Polyline/Distance/Angle/Trim/Method]: a Specify chamfer length on the first line <0.00>: 27 Specify chamfer angle from the first line <0>: 30 Select first line or [Polyline/Distance/Angle/Trim/Method]: Select second line: Command:
S1 S2
nainte
Dup
Opiunea P Command: chamfer (TRIM mode) Current chamfer Dist1 = 22.00, Dist2 = 10.00 Select first line or [Polyline/Distance/Angle/Trim/Method]: d Specify first chamfer distance <22.00>: 9 Specify second chamfer distance <9.00>: Select first line or [Polyline/Distance/Angle/Trim/Method]: p Select 2D polyline: (se selecteaz n S1) 4 lines were chamfered Polilinie Command:
S1
nainte
Dup