Documente Academic
Documente Profesional
Documente Cultură
Cap 3
Cap 3
Fig. 3.1
CAP.3
21
Fig. Fig.
3.3 3.2
22
5 prin folosirea tehnicii object snap (OSNAP) salt pe obiecte, care este
prezentat n cele ce urmeaz la 3.7.
23
Command: POINT
Specify a point: 50,70
Specify a point: @30,40
Specify a point: 100<20
Fig. 3.5
Specify first point: 75,93.5 1
Specify next point or [Undo]:
200,60
2
Specify next point or [Undo]:
300,180
3
Specify next point or [Undo]:
U
anulare 3
Specify next point or [Undo,Close]:
170,230
4
Specify next point or [Undo,Close]:
C
nchidere 1
Obervaii
n sistemul de uniti zecimale anglo-saxon, virgula de separare a ntregului de
zecimi este nlocuit prin punct.
Pentru primul segment se introduc coordonatele punctului iniial i ale celui
final; pentru segmentele urmtoare se introduc doar coordonatele punctului final,
considerndu-se drept punct iniial punctul final al segmentului precedent. ncepnd
24
Ra
di
us
am
Di
r
e te
Fig. 3.6
cu al patrulea punct, pe lng opiunea Undo este inclus i opiunea Close de
nchidere posibil a succesiunilor de entiti de tip Line.
ncheierea comenzii se face printr-un rspuns nul la promptul Specify next
point or [Undo,Close]:. La acelai prompt mai pot fi date rspunsurile:
U are ca efect tergerea ultimului segment de dreapt desenat;
C deseneaz un segment de dreapt care unete primul punct furnizat n
cadrul comenzii LINE cu ultimul punct specificat la promptul anterior.
Permite desenarea unui cerc (fig. 3.6), care poate fi definit prin:
Center point (centrul) i Radius (raza) sau Diameter (diametrul) (fig.3.6.a,b);
3 Points (3 puncte necoliniare) (fig.3.6.c);
2 Points (2 puncte diametral opuse) (fig.3.6.d);
Ttr (tan, tan, radius) tangent la 2 entiti cunoscute i raza dat (fig.3.6.e);
Tan, tan, tan - tangent la 3 entiti cunoscute (fig.3.6.f).
Sintaxa comenzii:
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr]:90,200
Specify radius of circle or [Diameter]<35>: 50
25
h
E
2
Fig. 3.7
a)
Command: ARC
Specify start point of arc or [Center]: se indic punctul S
Specify second point of arc or [Center/ENd]: se indic punctul I
26
Command: ARC
Specify start point of arc or [CEnter]: se indic punctul S
Specify second point of arc or [CEnter/ENd]: ce
Specify center point of arc: se indic centrul C
Specify end point of arc or [Angle/chord Length]: punctul E
c)
Command: ARC
Specify start point of arc or [CEnter]: punctul S
Specify second point of arc or [CEnter/ENd]: ce
Specify center point of arc: se indic C
Specify end point of arc or [Angle/chord Length]: a
Specify included angle: se indic unghiul A0
d)
Command: ARC
Specify start point of arc or [CEnter]: punctul S
Specify second point of arc or [CEnter/ENd]: ce
Specify center point of arc: se indic centrul C al arcului
Specify end point of arc or [Angle/chord Length]: L
Specify length of chord: se indic lungimea L a corzii
e)
Command: ARC
Specify start point of arc or [CEnter]: punctul S
Specify second point of arc or [CEnter/ENd]: en
Specify end point of arc: punctul E
Specify center point of arc or [Angle/Direction/Radius]: a
Specify included angle: se indic unghiul A0
f)
Command: ARC
Specify start point of arc or [CEnter]: punctul S
Specify second point of arc or [CEnter/ENd]: en
Specify end point of arc: punctul E
Specify center point of arc or [Angle/Direction/Radius]: r
Specify radius of arc: se indic raza R
Command: ARC
Specify start point of arc or [CEnter]: punctul S
Specify second point of arc or [CEnter/ENd]: en
Specify end point of arc: punctul E
Specify center point of arc or [Angle/Direction/Radius]: d
Specify tangent direction for the start point of arc: se indic direcia
tangentei n punctul de start al arcului
g)
h)
Command: ARC
27
Command: ARC
Specify start point of arc or [CEnter]: ce
Specify center point of arc: se indic centrul C al arcului
Specify start point of arc: punctul S
Specify end point of arc or [Angle/chord Length]: a
Specify included angle: se indic unghiul A0
j)
Command: ARC
Specify start point of arc or [CEnter]: ce
Specify center point of arc: se indic centrul C al arcului
Specify start point of arc: punctul S
Specify end point of arc or [Angle/chord Length]: L
Specify length of chord: se indic lungimea corzii subntinse
k)
Command: LINE
Specify first point: punctul 1
Specify next point or [Undo]: punctul 2
Specify next point or [Undo]:
Command: ARC
Specify start point of arc or [CEnter]:
Specify end point of arc: punctul E
ENDpoint - cel mai apropiat punct de capt situat pe un segment de dreapt sau
arc, fa de cursor (fig.3.8.c);
28
29
Track
point
MID
END
a)
c)
b)
d)
INT
e)
TAN
CEN
PER
QUA
AI
f)
i)
h)
g)
j)
NEA
PAR
TEXT
NOD
INS
k)
l)
n)
m)
Fig. 3.8
Fig. 3.9
Selectarea punctelor folosind modul Object Snap se face fie tastnd n zona de
dialog literele majuscule din denumirea ajutorului grafic dorit, fie prin clicarea cu
mouse-ul pe iconul corespunztor de pe bara de instrumente ajuttoare Object Snap.
n momentul selectrii unuia din modurile OSNAP, cursorul ia una din formele
prezentate n figura 3.9, situate i n caseta Drafting Settings din meniul Tools.