Documente Academic
Documente Profesional
Documente Cultură
◾ The "STATUS" column gives the latest known status of the standard.
◾ If a standard has been withdrawn and no replacement specification is listed, either the
specification was withdrawn without replacement or a replacement specification could not be
identified.
◾ DIN stands for "Deutsches Institut für Normung", meaning "German institute for standardisation". DIN
standards that begin with "DIN V" ("Vornorm", meaning "pre-issue") are the result of standardization
work, but because of certain reservations on the content or because of the divergent compared to a
standard installation procedure of DIN, they are not yet published standards.
Contents
DIN 1 to DIN 999
DIN 1 to DIN 99
DIN 100 to DIN 199
DIN 200 to DIN 299
DIN 300 to DIN 399
DIN 400 to DIN 499
DIN 500 to DIN 599
DIN 600 to DIN 699
DIN 700 to DIN 799
DIN 800 to DIN 899
DIN 900 to DIN 999
DIN 1000 to DIN 9999
DIN 1000 to DIN 1999
DIN 2000 to DIN 2999
DIN 3000 to DIN 3999
DIN 4000 to DIN 4999
DIN 5000 to DIN 5999
DIN 6000 to DIN 6999
DIN 7000 to DIN 7999
DIN 8000 to DIN 8999
DIN 9000 to DIN 9999
DIN 10000 to DIN 19999
DIN 10000 to DIN 10999
DIN 11000 to DIN 11999
DIN 12000 to DIN 12999
DIN 13000 to DIN 13999
DIN 14000 to DIN 14999
DIN 15000 to DIN 15999
DIN 16000 to DIN 16999
DIN 17000 to DIN 17999
DIN 18000 to DIN 18999
DIN 19000 to DIN 19999
DIN 20000 to DIN 29999
DIN 24000 to DIN 24999
DIN 28000 to DIN 28999
DIN 30000 to DIN 39999
DIN 31000 to DIN 31999
DIN 40000 to DIN 49999
DIN 51097 to DIN 59999
DIN 60000 to DIN 69999
DIN 70000 to DIN 79999
See also
References
External links
DIN 1 to DIN 99
Other org
DIN Title Status DIN replacement
replacement
Cone Pins,
DIN 1 Withdrawn DIN EN 22339 ISO 2339
untempered
Standard
DIN 3 Withdrawn
measurements
Technical
drawings - ISO 5456-1, ISO
Axonometric DIN ISO 5456-1, DIN ISO 5456-2, 5456-2,
DIN 5 Withdrawn
projections, DIN ISO 5456-3, DIN ISO 5456-4 ISO 5456-3, ISO
Isometric 5456-4
projection
Technical
drawings -
DIN 5-10 Withdrawn DIN ISO 10209-2 ISO 10209-2
projections,
terms
Projection
displays in
DIN 6 Normal, views Withdrawn DIN ISO 128, DIN EN ISO 128 ISO 128
and special
presentations
Whitworth pipe
threads 1/4"-6"
Thread
DIN 11 diameter, Withdrawn
sizes,
teaching
information
ISO general
purpose metric
screw threads
- Part 1:
Nominal sizes
DIN 13-1 for coarse Active
pitch threads;
nominal
diameter from
1 mm to
68 mm
ISO general
purpose metric
screw threads
- Part 2:
Nominal sizes
for 0,2 mm,
DIN 13-2 0,25 mm and Active
0,35 mm fine
pitch threads;
nominal
diameter from
1 mm to
50 mm
ISO general
purpose metric
screw threads
- Part 4:
Nominal sizes
for 0,75 mm
DIN 13-4 Active
fine pitch
threads;
nominal
diameter from
5 mm to
110 mm
ISO general
purpose metric
screw threads
- Part 5:
Nominal sizes
for 1 mm and
DIN 13-5 Active
1,25 mm fine
pitch threads;
nominal
diameter from
7,5 mm to
200 mm
ISO general
purpose metric
screw threads
- Part 6:
Nominal sizes
for 1,5 mm
DIN 13-6 Active
fine pitch
threads;
nominal
diameter from
12 mm to
300 mm
ISO general
purpose metric
screw threads
- Part 7:
Nominal sizes
DIN 13-7 for 2 mm fine Active
pitch threads;
nominal
diameter from
17 mm to
300 mm
Other org
DIN Title Status DIN replacement
replacement
DIN 13-8 ISO general Active
purpose metric
screw threads
- Part 8:
Nominal sizes
for 3 mm fine
pitch threads;
nominal
diameter from
28 mm to
300 mm
ISO general
purpose metric
screw threads
- Part 9:
Nominal sizes
DIN 13-9 for 4 mm fine Active
pitch threads;
nominal
diameter from
40 mm to
300 mm
ISO general
purpose metric
screw threads
- Part 10:
Nominal sizes
DIN 13-
for 6 mm fine Active
10
pitch threads;
nominal
diameter from
70 mm to
500 mm
ISO general
purpose metric
screw threads
- Part 11:
Nominal sizes
DIN 13-
for 8 mm fine Active
11
pitch threads;
nominal
diameter from
130 mm to
1000 mm
ISO general
purpose metric
screw threads
- Part 12: 1 to
300 mm
DIN 13- diameter
Active
12 coarse and
fine pitch
threads
Selected
diameters and
pitches
Active
Other org
DIN Title Status DIN replacement
replacement
DIN 13- ISO general
13 purpose metric
screw threads
- Part 13:
Selected sizes
for screws,
bolts and nuts
from 1 to
52 mm screw
thread
diameter and
limits of sizes
ISO general
purpose metric
DIN 13- screw threads
Active
19 - Part 19:
Nominal
profiles
ISO general
purpose metric
screw threads
- Part 20:
Limits of sizes
for coarse
DIN 13- pitch threads
Active
20 with the
preferred
tolerance
classes;
nominal sizes
from 1 mm to
68 mm
ISO general
purpose metric
screw threads
- Part 21:
Limits of sizes
for fine pitch
DIN 13- threads with
Active
21 the preferred
tolerance
classes;
Nominal
diameter from
1 mm to
24,5 mm
ISO general
purpose metric
screw threads
- Part 23:
Limits of sizes
for fine pitch
DIN 13- threads with
Active
23 the preferred
tolerance
classes;
Nominal
diameter from
53 mm to
110 mm
ISO general
purpose metric
screw threads
- Part 24:
Limits of sizes
for fine pitch
DIN 13- threads with
Active
24 the preferred
tolerance
classes;
Nominal
diameter from
112 mm to
180 mm
ISO general
purpose metric
screw threads
- Part 25:
Limits of sizes
for fine pitch
DIN 13- threads with
Active
25 the preferred
tolerance
classes;
Nominal
diameter from
182 mm to
250 mm
ISO general
purpose metric
screw threads
- Part 28:
Coarse and
Fine Screw
Threads from
DIN 13- 1 to 250 mm
Active
28 Screw Thread
Diameter;
Root Cross-
sections,
Tensile Stress
Cross-
sections and
Pitch Angles
ISO general
purpose metric
screw threads
- Part 50:
DIN 13- Combination
Active
50 of tolerance
classes for
formed
internal screw
threads
ISO general
purpose metric
screw threads
- Part 51:
External screw
threads for
DIN 13- transition fits
Active
51 (former: screw
threads for
interference
fit); tolerances,
limit
deviations,
limits of sizes
ISO general
purpose metric
screw threads
- Part 52:
DIN 13-
Multi-start Active
52
thread
tolerances and
deviation of
profile
Technical
drawings;
DIN 15-2 Withdrawn DIN ISO 128-24
lines; general
application
DIN 16 Withdrawn
Other org
DIN Title Status DIN replacement
replacement
Oblique
Standard
Typeface for
Drawings
Upright
Standard
DIN 17 Withdrawn
Typeface for
Drawings
Plain
bearings;
bearing metal
DIN 38 lining for thick- Active
walled
multilayer
plain bearings
Countersinks
for
countersunk
head screws
DIN 74 Active
(except
screws with
DIN EN 27721
head)
Thread run-
outs and
thread
undercuts for
DIN 76-1 Active
ISO metric
threads in
accordance
with DIN 13-1
Thread run-
outs and
thread
DIN 76-2 undercuts for Active
pipe threads
conforming to
ISO 228 part 1
Runouts,
Undercuts for
Trapezoidal
Threads,
Buttress
DIN 76-3 Threads and Active
Knuckle
Threads and
other Threads
of Coarse
Pitch
Product grade
DIN 85 A slotted pan Withdrawn DIN EN ISO 1580 ISO 1580
head screws
Product
slotted oval
head
DIN 88
countersunk
Withdrawn ISO 2010-1983[1]
machine
screws
Tab washers
DIN 93 Withdrawn
with long tab
Slotted Raised
Countersunk
DIN 95 Active
(Oval) Head
Wood Screws
Slotted Round
DIN 96 Head Wood Active
Screws
Rivets -
DIN 101 Technical Active
specifications
ISO Metric
Trapezoidal
DIN 103-1 Screw Active
Thread;
Profiles
ISO Metric
Trapezoidal
DIN 103-2 Screw Active
Thread;
General Plan
ISO Metric
Trapezoidal
Screw
Thread;
Allowances
and
DIN 103-3 Tolerances Active
for
Trapezoidal
Screw
Threads of
General
Purpose
ISO Metric
Trapezoidal
Screw
DIN 103-4 Active
Thread;
Nominal
Dimensions
ISO Metric
Trapezoidal
Screw
Threads;
Limiting
DIN 103-5 Active
Sizes for Nut
Threads from
8 to 100 mm
Nominal
Diameter
ISO Metric
Trapezoidal
Screw
Threads;
Limiting
DIN 103-6 Sizes for Nut Active
Threads from
105 to
300 mm
Nominal
Diameter
ISO Metric
Trapezoidal
Screw
Threads;
Limiting
DIN 103-8 Sizes for Bolt Active
Threads from
105 to
300 mm
Nominal
Diameter
ISO metric
trapezoidal
screw
threads;
gauging of
external and
DIN 103-9 Active
internal
threads;
gauge
dimensions
and design
features
Clay
masonry
units - Part 1:
Solid and DIN V 105-100, DIN EN
DIN V 105-1 Withdrawn EN 771-1
hollow bricks 771-1
with density
classes of
1,2
Clay
masonry
units - Part 2:
Solid and DIN V 105-100, DIN EN
DIN V 105-2 Withdrawn EN 771-1
hollow bricks 771-1
with density
classes
equal 1.0
Clay
masonry
units - Part 3:
DIN V 105-100, DIN EN
DIN 105-3 Tile and high Withdrawn EN 771-1
771-1
strength-
high-strength
clinker
Clay
masonry
units - Part 5:
Lightweight
DIN 105-5 long-hole Active
brick and
light long-
hole brick
panels
Clay
masonry
units - Part 6:
DIN V 105-6 Active
High
precision
units
Clay
masonry
units - Part
DIN V 105- 100: Clay
Active
100 masonry
units with
specific
properties
Washers;
medium type,
DIN EN ISO 7089, ISO 7089,
DIN 125 primarily for Withdrawn
DIN EN ISO 7090 ISO 7090
hexagon
bolts
Product
grade A
washers -
with a
hardness up
DIN EN ISO 7089, ISO 7089,
DIN 125-1 to 250 HV Withdrawn
DIN EN ISO 7090 ISO 7090
designed for
use with
hexagon
head bolts
and nuts
Product
grade A
washers -
with a
hardness up
DIN EN ISO 7089, ISO 7089,
DIN 125-2 to 300 HV Withdrawn
DIN EN ISO 7090 ISO 7090
designed for
use with
hexagon
head bolts
and nuts
Spring lock
washers with
DIN 127 Withdrawn
square ends
or tang ends
Curved and
DIN 128 wave spring Withdrawn
lock washers
Spring
washers,
DIN 137 Withdrawn DIN EN 137
curved or
wave
Bright Flat
Steel;
Dimensions,
DIN 174 Withdrawn DIN EN 10278
Permissible
Variations,
Weights
Polished
round steel;
Dimensions,
Permissible
DIN 175 deviations Withdrawn DIN EN 10278
according to
ISO
tolerance
zone h9
Technical
drawings;
Hatchings;
DIN 201 Representation Withdrawn DIN ISO 128-50 ISO 128-50
of cutting
edges and
materials
Machine
Reamers with
DIN 209 Active
Screwed-on
Blades
Fasteners -
Part 1:
Technical
DIN 267-1 delivery Withdrawn ISO 8992
conditions;
General
requirements
Fasteners -
Part 2:
Technical
delivery
conditions;
Bolts, Screws,
DIN 267-2 Nuts and Active DIN EN ISO 4759-1 ISO 4759-1
Similar
Threaded and
Formed Parts;
Types and
Dimensional
Accuracy
Fasteners -
Part 3:
Technical
delivery
conditions;
Property
classes for
DIN 267-3 Withdrawn DIN EN ISO 898-1 ISO 898-1
carbon steel
and alloy steel
bolts and
screws;
Conversion of
property
classes
Fasteners -
Part 4:
Technical
delivery
DIN 267-4 conditions; Withdrawn DIN EN ISO 898-2 ISO 898-2
Property
classes for
nuts (previous
classes)
Fasteners -
Part 6:
Technical
delivery
conditions;
DIN 267-6 Active
Designs and
accuracy of
measurement
for product
grade F
Fasteners -
Part 9:
Technical
delivery
DIN 267-7 Withdrawn DIN EN ISO 898-1 ISO 898-1
conditions;
Bolts made of
unalloyed or
low-alloy steels
Fasteners -
Part 9:
Technical
delivery
DIN 267-9 conditions; Withdrawn DIN EN ISO 4042 ISO 4042
Components
with
Electroplated
Coatings
Fasteners -
Part 10:
Technical
DIN 267-10 delivery Withdrawn DIN EN ISO 10684 ISO 10684
conditions; Hot
dip galvanized
parts
Fasteners -
Part 11:
Technical
delivery
conditions
DIN 267-11 (with additions Withdrawn
to ISO 3506);
Corrosion-
resistant
stainless steel
fasteners
Other org
DIN Title Status DIN replacement
replacement
DIN 267-12 Fasteners - Withdrawn DIN EN ISO 2702 ISO 2702
Part 12:
Technical
delivery
conditions;
Self-tapping
screws
Fasteners -
Part 13:
Technical
delivery
conditions;
Components
for Bolted
Connections
Made Mainly
from Materials
DIN 267-13 Active
Exhibiting a
High Impact
Strength at
Low
Temperature
or from
Materials with
a High
Temperature
Strength
Fasteners -
Part 15:
Technical DIN EN ISO 2320, ISO 2320,
delivery DIN EN ISO 3506-1, ISO 3506-1,
DIN 267-15 Withdrawn
conditions; DIN EN ISO 3506-2, ISO 3506-2,
Prevailing DIN EN ISO 3506-3 ISO 3506-3
torque type
nuts
Fasteners -
Part 18:
Technical
delivery
DIN 267-18 Withdrawn DIN EN 28839 ISO 8839
conditions;
Components
made of Non-
ferrous Metals
Fasteners -
Part 19:
Technical
delivery
DIN EN ISO 26157-1, ISO 6157-1,
DIN 267-19 conditions; Withdrawn
DIN EN ISO 26157-3 ISO 6157-3
Surface
discontinuities
on bolts and
screws
Fasteners -
Part 21:
Technical DIN EN ISO 6157-2, ISO 6157-2,
DIN 267-21 delivery Withdrawn DIN EN ISO 10484, ISO 10484,
conditions; DIN EN ISO 10485 ISO 10485
Widening test
on nuts
Fasteners -
Part 23:
Technical
delivery
conditions;
DIN 267-23 Withdrawn DIN EN ISO 898-6 ISO 898-6
Property
classes for
nuts with fine
thread (ISO
classes)
Fasteners -
Part 24:
Technical
delivery
DIN 267-24 conditions; Active
Property
classes for
nuts (Hardness
classes)
Fasteners -
Part 25:
Technical
delivery
DIN 267-25 conditions; Withdrawn DIN EN 20898-7 EN 20898-7
Torsion testing
of M1 to M10
bolts and
screws
Fasteners -
Part 26:
Technical
delivery
DIN 267-26 conditions; Active
Conical spring
washers for
bolt/nut
assemblies
Fasteners -
Part 27:
Technical
specifications;
DIN 267-27 Active
Steel screws,
bolts and studs
with adhesive
coating
Other org
DIN Title Status DIN replacement
replacement
DIN 267-28 Fasteners - Active
Part 28:
Technical
specifications;
Steel screws,
bolts and studs
with locking
coating
Fasteners -
Part 29:
Technical
specifications;
Product grades
for parts for
DIN 267-29 bolted Withdrawn
connections for
use at
temperatures
ranging from -
200 °C to
+700 °C
Fasteners -
Part 30:
Technical
specifications;
DIN 267-30 Active
Metric thread
rolling screws
of property
class 10.9
Building costs;
DIN 276-1 Part 1: Building Active
construction
Building costs;
Part 2:
DIN 276-2 Withdrawn
Classification
of cost
Building costs;
Part 3:
DIN 276-3 Withdrawn
Ascertainment
of cost
Wing nuts
DIN 315 with rounded Active
wings
Wing screws
DIN 316 with rounded Active
wings
Preferred
Numbers and
Series of
Preferred
Numbers;
DIN 323-1 Basic Withdrawn
Values,
Calculated
Values,
Rounded
Values
Preferred
Numbers and
Series of
DIN 323-2 Active
Preferred
Numbers;
Introduction
60° centre
holes; types
DIN 332-1 Active
R, A, B, and
C
Center holes
60° with
thread for
DIN 332-2 shaft ends Active
for rotating
electrical
machines
Centre holes
for rail
DIN 332-4 Active
vehicles
axles
Machine
tools; 60°
DIN 332-7 Active
centre holes;
dimensioning
Centre holes
90°, form S;
DIN 332-8 dimensions, Active
determination
process
Parallel
shank twist
DIN 338 Active
drills, jobber
series
Sets of taps -
Sets of 3
taps for
DIN 352 Active
metric coarse
ISO-threads
M1 to M68
Machine taps
with
reinforced
shank for
coarse pitch
metric ISO-
DIN 371 threads M1 Active
to M10 and
fine pitch
metric ISO-
threads M1 ×
0,2 to M10 ×
1,25
Machine
screwing
taps for fine
DIN 374 pitch metric Active
ISO-threads
M3 × 0,2 to
M52 × 4
Slotted
DIN 404 capstan Active
screws
Engineering
drawing
practice;
DIN 406-
dimensioning; Active
10
concepts and
general
principles
Engineering
drawing
DIN 406- practice;
Active
11 dimensioning;
principles of
application
Engineering
drawing
practice;
dimensioning;
tolerancing of
DIN 406-
linear and Active
12
angular
dimensions
(modified
version of ISO
406:1987)
Slotted set
DIN 417 screws with Withdrawn DIN EN 27435 ISO 7435
long dog point
Slotted
headless
DIN 427 Withdrawn DIN EN ISO 2342 ISO 2342
screws with
chamfered end
Hexagon nuts,
DIN 428 Withdrawn DIN EN ISO 4034 ISO 4034
Grade C
Washers for
use with
DIN 433 Withdrawn DIN EN ISO 7092 ISO 7092
cheese head
screws
Product grade
A washers -
with a
hardness up to
DIN 433-1 250 HV Withdrawn DIN EN ISO 7092 ISO 7092
designed for
use with
cheese head
screws
DIN 433-2 Product grade Withdrawn DIN EN ISO 7092 ISO 7092
A washers -
with a
hardness up to
Other org
DIN Title Status DIN replacement
replacement
300 HV
designed for
use with
cheese head
screws
Slotted set
DIN 438 screws with Withdrawn DIN EN 27436 ISO 7436
cup point
Hexagon thin DIN EN ISO 4035, DIN EN ISO 4035, ISO 4036,
DIN 439 Withdrawn
nuts ISO 4036, DIN EN ISO 8675 ISO 8675
Unchamfered
hexagon thin
DIN 439-1 Withdrawn DIN EN ISO 4036 ISO 4036
nuts - Product
grade B
Chamfered
hexagon thin
DIN EN ISO 4035, DIN EN
DIN 439-2 nuts - Product Withdrawn ISO 4035, ISO 8675
ISO 8675
grades A and
B
Washers for
DIN 440 use in timber Withdrawn DIN EN ISO 7094 ISO 7094
constructions
Graphical
Representation
DIN 461 Active
in Systems of
Coordinates
Machine Tools;
Internal Tab
Washers for
Slotted Round
DIN 462 Active
Nuts for Hook
Spanner
according to
DIN 1804
Knurled thumb
DIN 464 screws, high Active
type
Knurled nuts,
DIN 466 Active
high type
Knurled nuts,
DIN 467 Active
low type
Circlips
(retaining
rings) for
DIN 471 Active
shafts; Normal
type and
heavy type
DIN 476 Paper sizes Withdrawn DIN EN ISO 216 ISO 216
Gas cylinder
valves for
cylinder test
pressures up
DIN 477-1 Active
to 300 bar -
Part 1: Valve
inlet and outlet
connections
Square head
DIN 479 bolts with short Active
dog point
Metal
washers;
DIN 522 technical Withdrawn DIN EN ISO 4759-3 ISO 4759-3
delivery
conditions
Round
nuts with
DIN 548 set pin Active
holes in
side
Slotted
set
DIN 551 screws Withdrawn DIN EN 24766 ISO 4766
with flat
point
Slotted
set
DIN 553 screws Withdrawn DIN EN 27434 ISO 7434
with cone
point
M5 to
M100x6
hexagon
DIN 555 Withdrawn DIN EN ISO 4034 ISO 4034
nuts -
Product
grade C
Hexagon
DIN 558 head Withdrawn DIN EN ISO 4018 ISO 4018
screws
Collar
eyebolts
DIN 580 Active
for lifting
purposes
M5 to M52
hexagon
DIN 601 head bolts; Withdrawn DIN EN ISO 4016 ISO 4016
product
grade C
Mushroom
head
DIN 603 Active
square
neck bolts
Hexagon
fits bolts
DIN 609 Active
with long
thread
Rolling
bearings;
single row
DIN 625-1 radial Active
contact
ball
bearings
Rolling
bearings;
double row
DIN 625-3 radial Active
contact
ball
bearings
Rolling
bearings;
radial
contact
DIN 625-4 groove ball Active
bearings
with
flanged
outer ring
Knurled
thumb
DIN 653 Active
screws,
low type
Envelopes
DIN 678-1 - Part 1: Active
Sizes
Envelopes
- Part 2:
Envelopes
for
Processing
DIN 678-2 Active
in
Enveloping
Machines,
Size C6 to
C4
DIN 700 to DIN 799
Other org
DIN Title Status DIN replacement
replacement
Tested,
non-
calibrated,
DIN 763 Active
long-link
round steel
chains
Calibrated
and tested
round steel
link chains
DIN 764-1 for Active
continuous
conveyors;
grade 2,
pitch 3,5d
Calibrated
and tested
round steel
link chains
DIN 764-2 for Active
continuous
conveyors;
grade 3,
pitch 3,5d
Calibrated
and tested
DIN 766 grade 3 Active
round steel
link chains
Foundation
DIN 799-1 Active
Blocks
Standards
DIN 820-1 Work - Part 1: Active
Principles
Standardization
- Part 2:
Presentation of
standards;
DIN 820-2 Active
examples for
presentation of
figures, tables
and part lists
Standardization
DIN 820-3 - Pdfart 3: Active
Concepts
Standardization
- Part 4:
DIN 820-4 Active
Working
procedure
Standardization
- Part 11:
Presentation of
Standards
concerning
DIN 820-11 safety Active
regulations
which are VDE-
Specifications
or VDE-
Guidelines
Standardization
- Part 12:
Presentation of
DIN 820-12 standards Active
concerning
safety
regulations
Standardization
- Part 13:
Adoption of
European
documents of
DIN 820-13 Active
CEN,
CENELEC and
of ETSI;
Concepts and
presentation
Standardization
- Part 15:
Implementation
of ISO and IEC
DIN 820-15 Active
international
documents;
Concepts and
presentation
Other org
DIN Title Status DIN replacement
replacement
DIN 820-120 Standardization Active
- Part 120:
Guidelines for
the inclusion of
safety aspects
in standards
(ISO/IEC Guide
51:1999)
Technical
drawings;
DIN 824 Active
Folding to filing
size
Hand Operated
Wrenches and
DIN 899 Sockets; Withdrawn DIN ISO 1711-1 ISO 1711-1
Technical
Specifications
internal drive
pipe plugs for
the sealing of
DIN
holes with Active
906
cylindrical
internal
threads
Hexagon
socket screw
DIN
plugs with Active
908
parallel screw
thread
Hexagon-
DIN duty hexagon
Active
910 head screw
plugs
Hexagon
DIN
Socket Screw Withdrawn DIN ISO 2936 ISO 2936
911
Keys
Hexagon
socket head DIN EN ISO
DIN cap screws 4762, ISO 4762,
Withdrawn
912 (modified DIN EN ISO ISO 21269
version of 21269
ISO 4762)
Hexagon
socket set
DIN screws with DIN EN ISO
Withdrawn ISO 4026
913 flat point (ISO 4026
4026
modified)
Hexagon
socket set
DIN screws with DIN EN ISO
Withdrawn ISO 4027
914 cone point 4027
(ISO 4027
modified)
Hexagon
socket set
DIN screws with DIN EN ISO
Withdrawn ISO 4028
915 full dog pointt 4028
(ISO 4028
modified)
Hexagon
socket set
DIN screws with DIN EN ISO
Withdrawn ISO 4029
916 cup point 4029
(ISO 4029
modified)
Overview of
DIN European
Active
918-3 Standards for
fasteners
Technical
Drawings;
DIN
Wood Active
919-1
Processing;
Principles
Slotted pan
DIN head screws
Active
921 with large
head
Slotted pan
DIN
head screws Active
923
with shoulder
DIN Hexagon
Active
929 weld nuts
Fine thread
DIN pitch partially DIN 931-1, DIN
Withdrawn
930 threaded 931-2
screws
M1,6 to M39
Hexagon Cap
Screws
DIN Partially DIN EN ISO
Withdrawn ISO 4014
931-1 Threaded - 4014
Product
grades A and
B
M42 to
M160x6
Hexagon Cap
DIN Screws DIN EN ISO
Withdrawn ISO 4014
931-2 Partially 4014
Threaded -
Product
grade B
M1,6 to M52
Hexagon Cap
DIN Screws Fully DIN EN ISO
Withdrawn ISO 4017
933 Threaded - 4017
Product
grades 8.8
Hexagon
slotted nuts
and castle
nuts with
DIN metric coarse
Active
935-1 and fine pitch
thread -
Product
grades A and
B
M42 to
M160x6
DIN hexagon
Active
935-2 head bolts;
product grade
B
Hexagon
slotted nuts
with metric
DIN
coarse pitch Active
935-3
thread -
Product
grade C
M8 to M52
and M8x1 to
M52x3
DIN
hexagon thin Withdrawn
936
nuts; product
grades A and
B
Studs with a
length of
DIN
engagement Active
938
equal to
about 1 d
Studs with a
length of
DIN
engagement Active
939
equal to
about 1,25 d
Determination
of coefficient
of friction of
DIN bolt/nut DIN EN ISO
Withdrawn ISO 16047
946 assemblies 16047
under
specified
conditions
Withdrawn
DIN Other org
DIN Title Status
replacement replacement
DIN M8x1 to DIN EN ISO ISO 8765,
960 M100x4 8765, ISO 8676
hexagon DIN EN ISO
head bolts 8676
with fine pitch
thread -
Product
grades A and
B
M8x1 to
M52x3
hexagon
head bolts
DIN DIN EN ISO
with fine pitch Withdrawn ISO 8676
961 8676
thread -
Product
grades A and
B
Designation
DIN
system for Active
962
fasteners
Slotted
countersunk
head screws
(with
DIN DIN EN ISO
countersunk Withdrawn ISO 2009
963 2009
heads as
specified in
ISO 2009-
1972)
Slotted raised
DIN countersunk DIN EN ISO
Withdrawn ISO 2010
964 oval head 2010
screws
Cross
DIN EN ISO ISO 7046-1,
recessed
DIN 7046-1, ISO 7046-2
countersunk Withdrawn
965 DIN EN ISO (http://www.iso.org/iso/catalogue_detail.htm?
flat head
7046-2 csnumber=57374)
screws
Cross
recessed
DIN DIN EN ISO
raised Withdrawn ISO 7047
966 7047
countersunk
head screws
Hexagon
nuts; Style 1;
Metric coarse
DIN thread, DIN EN ISO
Withdrawn ISO 4032
970 Product 4032
grades A and
B; ISO 4032
modified
Style 2
hexagon nuts
with metric
DIN fine pitch DIN EN ISO
Withdrawn ISO 8674
971-2 thread; 8674
property
classes 10
and 12
M5 to M39
hexagon
nuts; style 1;
DIN DIN EN ISO
product grade Withdrawn ISO 4034
972 4034
C (modified
version of
ISO 4034)
DIN Threaded
Withdrawn
975 rods
Metric
DIN interference-
Active
976-2 fit thread stud
bolts
Hexagon
DIN DIN EN ISO
weld nuts Withdrawn ISO 21670
977 21670
with flange
Hexagon thin
slotted nuts
and castle
nuts with
DIN metric coarse
Active
979 and fine pitch
thread -
Product
grades A and
B
Locknuts for
DIN use with
Active
981 rolling
bearings
Retaining
rings with
DIN lugs for use
Active
983 on shafts
(external
circlips)
Prevailing
torque type
DIN hexagon thin DIN EN ISO
Withdrawn ISO 10511
985 nuts with 10511
nonmetallic
insert
Prevailing
torque type
hexagon
DIN
domed cap Active
986
nuts with
non-metallic
insert
Shim rings
DIN and
Active
988 supporting
rings
Hot rolled
I-sections - Part
1: Narrow
flange
I-sections,
DIN 1025-1 Active
I-serie -
Dimensions,
masses,
sectional
properties
Hot rolled
I-beams - Part
2: Wide flange
I-beams, IPB-
DIN 1025-2 serie; Active
dimensions,
masses,
sectional
properties
Hot rolled
I-beams; wide
flange I-beams,
light pattern,
DIN 1025-3 IPBl-serie; Active
dimensions,
masses,
sectional
properties
Hot rolled
I-beams; wide
flange I-beams
heavy pattern,
DIN 1025-4 IPBv-serie; Active
dimensions,
masses,
sectional
properties
Hot rolled
I-beams;
medium flange
I-beams, IPE-
DIN 1025-5 serie; Active
dimensions,
masses,
sectional
properties
Units - Part 1:
DIN 1301-1 Names and Active
Symbols
Units - Part 2:
Submultiples
DIN 1301-2 Active
and Multiples
for General Use
General
Mathematical
DIN 1302 Active
Symbols and
Concepts
Vectors,
matrices,
DIN 1303 tensors; Active
symbols and
concepts
Letter symbols
for physical
DIN 1304-1 quantities - Part Active
1: Symbols for
general use
Letter symbols
for physical
quantities - Part
DIN 1304-2 2: Symbols for Active
use in
meteorology
and geophysics
Letter symbols
for physical
quantities - Part
DIN 1304-3 3: Symbols for Active
use in electric
power
engineering
Letter symbols
for physical
quantities - Part
DIN 1304-5 Active
5: Symbols for
use in fluid
mechanics
Letter symbols
for physical
quantities - Part
9: Symbols for
use in the field
DIN 1304-8 Active
of static
converters
using
semiconductor
devices
(Mechanical)
vibrations,
oscillations and
vibration
DIN 1311-1 Active
systems - Part
1: Basic
concepts,
survey
(Mechanical)
vibrations,
oscillations and
vibration
systems - Part
DIN 1311-2 Active
2: Linear
vibration
systems with
single degree of
freedom
(Mechanical)
vibrations,
oscillations and
vibration
systems - Part
3: Linear time-
DIN 1311-3 Active
invariant
vibration
systems with a
finite number of
degrees of
freedom
Vibration;
Vibrating
DIN 1311-4 Active
Continua,
Waves
Physical
Quantities and
Equation;
DIN 1313 Active
Concepts,
Methods of
Writing
Angle;
DIN 1315 Active
Concepts, Units
Fundamentals
of Metrology –
DIN 1319-1 Active
Part 1: Basic
Terminology
Basic Concepts
in Metrology –
Part 3:
Terminology
Relating To the
Uncertainty of
DIN 1319-3 Measurement Active
and the
Assessment of
Measuring
Instruments and
Measuring
Equipment
Basic Concepts
in Metrology –
Part 4:
Treatment of
DIN 1319-4 Active
Uncertainties in
the Evaluation
of
Measurements
Acoustics;
DIN 1320 Active
Terminology
Electromagnetic
DIN 1324-1 Field - Part 1. Active
State Quantities
Electromagnetic
Field - Part 2.
DIN 1324-2 Active
Material
Quantities
Electromagnetic
Field - Part 3.
DIN 1324-3 Active
Electromagnetic
Waves
Vocabulary for
value
management,
value analysis
and functional
DIN 1325-1 Active
analysis - Part
1: Value
analysis and
functional
analysis
Acoustics;
DIN 1332 Withdrawn DIN EN ISO 80000-8 ISO 80000-8
Symbols
Presentation of
DIN 1333 Active
Numerical Data
Writing and
DIN 1338 Typesetting of Active
Formulae
Time; Calendar,
Numbering of
DIN 1355-1 Weeks, Date of Withdrawn
Day, (Clock)
Time
Arrangement
and Numbering
in Texts;
DIN 1421 Active
Clauses,
Paragraphs,
Enumerations
Publications in
Sciences,
Technology,
Economy and
DIN 1422-1 Active
Administration;
Presentation of
Manuscripts
and Typoscripts
Publications in
Sciences,
Technology,
Economy and
Administration;
DIN 1422-2 Active
Presentation of
Clean Copies
for
Reprographic
Use
Publications in
Sciences,
Technology,
DIN 1422-3 Economy and Active
Administration;
Typographical
Presentation
Medium type
DIN 1440 washers for Withdrawn DIN EN 28738 ISO 8738
pins
Clevis pins
DIN 1443 Withdrawn DIN EN 22340 ISO 2340
without head
Legibility of
DIN 1450 Typefaces – Active
General
Lettering -
Linear-Antiqua
DIN 1451-1 Active
without serifes
– General
Typefaces -
lineal Linear-
DIN 1451-2 Antiqua; Active
lettering for
transportation
Lettering -
Linear-Antiqua
DIN 1451-3 without serifes; Active
lettering for
printing
Typefaces -
lineal Linear-
Antiqua;
DIN 1451-4 stenciled Active
lettering for
engraving and
other processes
Guidelines for
the
Establishment
and
DIN 1463-1 Active
Development of
Thesauri;
Monolingual
Thesauri
Guidelines for
the
Establishment
and
DIN 1463-2 Active
Development of
Thesauri;
Multilingual
Thesauri
Grooved Pins,
DIN 1471 Full Length Withdrawn DIN EN 8744 ISO 8744
Taper-grooved
Grooved Pins,
DIN 1472 Half Length Withdrawn DIN EN 8745 ISO 8745
Taper-grooved
Grooved Pins,
Full Length
DIN 1473 Parallel- Withdrawn DIN EN ISO 8740 ISO 8740
grooved with
Chamfer
Grooved Pins,
Half Length
DIN 1474 Withdrawn DIN EN 8741 ISO 8741
Reverse-
grooved
Grooved Pins,
DIN 1475 Third Length Withdrawn DIN EN 8742 ISO 8742
Centre-grooved
Round Head
DIN 1476 Withdrawn DIN EN 8746 ISO 8746
Grooved Pins
Countersunk
DIN 1477 Head Grooved Withdrawn DIN EN 8747 ISO 8747
Pins
Spring-Type
Straight Pins
DIN 1481 Withdrawn DIN EN ISO 8752 ISO 8752
(Roll Pins) -
Heavy Type
Bibliographic
references to
documents -
Part 1: Full
DIN 1505-1 Active
References to
Printed and
Published
Documents
Bibliographic
references to
DIN 1505-2 documents - Active
Part 2: Rules
for Citing
Bibliographic
references to
documents -
DIN 1505-3 Part 3: Indexes Active
of cited
documents
(bibliographies)
Tools for
moulding - Part
DIN 1530-1 1: Ejector pins Active
with cylindrical
head
Tools for
moulding - Part
DIN 1530-2 Active
2: Shouldered
ejector pins
Tools for
moulding - Part
DIN 1530-3 3: Ejector pins Active
with conical
head
Hexagon
DIN 1587 Active
domed cap nuts
Soft Solders;
Composition,
DIN 1707 Technical Active DIN EN ISO 9453 ISO 9453
Delivery
Condition
Aluminium and
aluminium
alloys -
DIN 1712 Unalloyed
Withdrawn DIN EN 576 EN 576
Part 1 aluminium
ingots for
remelting –
Specifications
Aluminium;
DIN 1712
Half-Finished Withdrawn DIN EN 573-3 EN 573-3
Part 3
Products
Strips, Plates
and Sheets of
DIN 1783 Withdrawn DIN EN 485-4 EN 485-4
Aluminium and
Wrought
Seamless
Drawn Copper
DIN 1786 Withdrawn DIN EN 1057 EN 1057
Tubes for
Piping Systems
Round Rod of
Aluminium
DIN 1798 Withdrawn DIN EN 754-3 EN 754-3
(Highest Grade
Aluminium)
Graphical
Representation
DIN 1912-1 of Welded, Withdrawn DIN EN ISO 17659 ISO 17659
Soldered and
Brazed Joints
Graphical
Representation
DIN 1912-2 of Welded, Withdrawn DIN EN ISO 6947 ISO 6947
Soldered and
Brazed Joints
Graphical
Representation
of Welded,
Soldered and
Brazed Joints;
DIN 1912-4 Active
Concepts and
Terms for
Soldered and
Brazed Joints
and Seams
Symbolic
Representation
on Drawings of
DIN 1912-5 Withdrawn DIN EN 22553 ISO 2553
Welded,
Soldered and
Brazed Joints
Construction
contract
procedures
(VOB) - Part A:
General
DIN 1960 Active
provisions
relating to the
award of
construction
contracts
Construction
contract
procedures
(VOB) - Part B:
General
DIN 1961 Active
conditions of
contract relating
to the execution
of construction
work
DIN 2000 to DIN 2999
Other org
DIN Title Status DIN replacement
replacement
Alphanumeric
office
machines -
Alphanumeric
keyboards,
DIN 2112 Withdrawn DIN 2137-1, DIN 2137-2
keyboard
arrangement
for manually
operated
typewriters
Alphanumeric
office
machines;
alphanumeric
keyboards,
DIN 2127 keyboard Withdrawn DIN 2137-1, DIN 2137-2
arrangement
for electro-
mechanical
operated
typewriters
Keyboards
for data and
text input -
DIN 2137-1 Part 1: Active
German
keyboard
layout
Keyboards
for data and
text input -
DIN 2137-2 Active
Part 2:
Additional
requirements
Sets of 2 taps
for metric fine
DIN 2181 ISO-threads Active
M1 × 0,2 to
M52 × 4
Vocabulary
of
DIN 2342-1 terminology; Active
basic
concepts
Seamless
precision
DIN 2391-1 steel tubes - Canceled DIN EN 10305-1 EN 10305-1
Part 1:
Dimensions
Seamless
Steel Pipes
and Tubes -
DIN 2448 Dimensions, Canceled DIN EN 10220 EN 10220
Conventional
Masses per
Unit Length
Blank flanges
- Nominal
DIN 2527 Withdrawn DIN EN 1092-1 EN 1092-1
pressure 6 to
100
Capillary
Fittings;
DIN 2860 Withdrawn
Bends 180°
of Copper
Pipe threads
for tubes and
fittings;
parallel
DIN 2999-1 internal Withdrawn DIN EN 10226-1 EN 10226-1
thread and
taper external
thread; tread
dimensions
Whitworth
Pipe Threads
for Tubes
and Fittings;
Cylindrical
Internal
Thread and
DIN 2999-2 Withdrawn DIN EN 10226-3 EN 10226-3
Conical
External
Thread,
Gauging
System and
Use of
Gauges
Whitworth
Pipe Threads
for Tubes
DIN 2999-3 Withdrawn DIN EN 10226-3 EN 10226-3
and Fittings;
Gauge
Dimensions
Pipe threads
for tubes and
fittings; sizes
for taper
DIN 2999-4 screw limit Withdrawn DIN EN 10226-3 EN 10226-3
plug gauges
for parallel
internal
thread
Other org
DIN Title Status DIN replacement
replacement
DIN 2999-5 Whitworth Withdrawn DIN EN 10226-3 EN 10226-3
Pipe Threads
for Tubes
and Fittings;
Cylindrical
Screw Limit
Ring Gauges
for Gauging
Conical
External
Threads,
Sizes
Whitworth
Pipe Threads
for Tubes
DIN 2999-6 and Fittings; Withdrawn DIN EN 10226-3 EN 10226-3
Conical
Screw Check
Plugs, Sizes
DIN 3000 ,
Hose
clamps
DIN 3017-1 with worm ,
gear drive;
shape A
Hose
clamps -
Part 2:
DIN 3017-2 Clamps ,
with
fastening
lugs
Hose
clamps -
DIN 3017-3 ,
Part 3: Bolt
clamps
Hose
clamps -
Part 4:
DIN 3017-4 ,
Technical
delivery
conditions
Hose
clamps -
Part 5:
Wide strip
hose
DIN 3017-5 clamps ,
with
fastening
lugs;
Types D
and E
Sealing
rings
("O-rings")
with
DIN 3770 special Withdrawn
accuracy,
made of
elastomeric
materials
Fluid
systems;
O-rings;
DIN 3771-3 Active
materials,
field of
application
Water
DIN engineering,
Active
4048-1 terms - Part 1:
Dam plants
Water
engineering,
DIN
terms - Part 2: Active
4048-2
Waterpower
plants
Correction of
DIN 4054 Active
waterways, terms
Subsoil, Field
DIN investigations -
Active
4094-1 Part 1: Cone
penetration tests
Fire behaviour of
building materials
and elements -
DIN Part 1:
Active
4102-1 Classification of
building materials
- Requirements
and testing
Fire Behaviour of
Building Materials
and Building
Components -
DIN
Part 2: Building Active
4102-2
Components;
Definitions,
Requirements
and Tests
Fire Behaviour of
Building Materials
and Building
Components -
DIN Part 3: Fire Walls
Active
4102-3 and Non-load-
bearing External
Walls; Definitions,
Requirements
and Tests
Fire behaviour of
building materials
and elements -
Part 4: Overview
DIN
and design of Active
4102-4
classified building
materials,
elements and
components
Fire Behaviour of
Building Materials
and Building
Components -
DIN
Part 6: Ventilation Active
4102-6
Ducts;
Definitions,
Requirements
and Tests
Fire behaviour of
building materials
and elements -
DIN
Part 7: Roofing - Active
4102-7
Concepts,
requirements and
testing
Fire behaviour of
building materials
DIN
and components Active
4102-8
- Part 8: Small-
scale test furnace
Fire behaviour of
building materials
and elements -
Part 9: seals for
DIN
cable Active
4102-9
penetrations;
concepts,
requirements and
testing
Fire behaviour of
building materials
and building
components -
Part 10: pipe
encasements,
pipe bushings,
DIN
service shafts Active
4102-11
and ducts, and
barriers across
inspection
openings;
terminology,
requirements and
testing
Fire behaviour of
building materials
and elements -
DIN Part 13: Fire
Active
4102-13 resistant glazing;
concepts,
requirements and
testing
Fire behaviour of
building materials
and elements -
Part 14:
DIN Determination of
Active
4102-14 the burning
behaviour of floor
covering systems
using a radiant
heat source
Fire behaviour of
building materials
DIN
and elements - Active
4102-15
Part 15:
"Brandschacht"
Fire behaviour of
building materials
DIN and elements -
Active
4102-16 Part 16:
"Brandschacht"
tests
Fire behaviour of
building materials
and elements -
Part 17:
determination of
DIN melting point of
Active
4102-17 mineral fibre
insulating
materials;
concepts,
requirements and
testing
Fire behaviour of
building materials
and building
components -
Part 22:
DIN
Application Active
4102-22
standard for DIN
4102-4 based on
the design of
partial safety
factors
Thermal
protection and
DIN energy economy
Active
4108-1 in buildings - Part
1: Quantities and
units
Thermal
protection and
energy economy
DIN
in buildings - Part Active
4108-2
2: Minimum
requirements to
thermal insulation
Thermal
protection and
energy economy
in buildings - Part
3: Protection
DIN against moisture
Active
4108-3 subject to climate
conditions;
Requirements
and directions for
design and
construction
Thermal
insulation and
energy economy
of buildings - Part
7: Airtightness of
DIN
building, Active
4108-7
requirements,
recommendations
and examples for
planning and
performance
Structural
vibration - Part 1:
DIN
Prediction of Active
4150-1
vibration
parameters
Structural
vibration - Part 2:
DIN
Human exposure Active
4150-2
to vibration in
buildings
Structural
vibration - Part 3:
DIN
Effects of Active
4150-3
vibration on
structures
Service and
working scaffolds
- Part 1: Service
DIN scaffolds -
Active
4420-1 Performance
requirements,
general design,
structural design
Photographic
sensitometry,
determination of
DIN 4512-1:1971-04, DIN
optical density:
4512-3:1973-01, DIN
"Photographische
DIN 4512 Withdrawn 4512-4:1977-06, DIN
Sensitometrie,
4512-5:1977-10, DIN
Bestimmung der
4512-6:1980-07
optischen Dichte"
(1934-01, 1957-
11, 1961-10)
Photographic
sensitometry,
determination of
the speed of
black and white
DIN Withdrawn
negative DIN ISO 6:1996-02 ISO 6
4512-1 (2000–09)
materials for
pictorial
photography
(1971-04, 1993-
05)
Photographic
sensitometry,
DIN 4512-7:1993-01, DIN
DIN determination of
Withdrawn 4512-8:1993-01, DIN
4512-3 diffuse
4512-9:1993-01
transmission
density (1973-01)
Other org
DIN Title Status DIN replacement
replacement
DIN Photographic Withdrawn DIN ISO 2240:1998-06 ISO 2240
4512-4 sensitometry; (2002–06)
determination of
the speed of
colour reversal
films (1977-06,
1985-08)
Photographic
sensitometry;
determination of
DIN Withdrawn
the speed of DIN ISO 5800:1998-06 ISO 5800
4512-5 (2002–06)
colour negative
films (1977-10,
1990-11)
Photographic
sensitometry;
DIN sensitometric
Withdrawn
4512-6 illuminants and
light sources
(1980-07)
Photographic
sensitometry,
determination of
DIN optical density;
Active
4512-7 concepts,
symbols and
notations (1993-
01)
Photographic
sensitometry,
determination of
DIN optical density;
Active
4512-8 geometric
conditions for
transmission
density (1993-01)
Photographic
sensitometry,
determination of
DIN
optical density; Active
4512-9
spectral
conditions (1993-
01)
Photographic
sensitometry,
determination of
DIN optical density;
Active
4512-10 geometric
conditions for
reflection density
(1993-01)
Energetic
evaluation of
heating and
ventilation
DIN V systems in
Active
4701-12 existing buildings
- Part 12: Heat
generation and
domestic hot
water generation
Statistics on
German
meteorological
data for
calculating the
DIN 4710 Active
energy
requirements for
heating and air
conditioning
equipment
Physics of
radiation in the
field of optics and
illuminating
DIN 5031-1 engineering - Part Active
1: Quantities,
symbols and
units of radiation
physics
Physics of
radiation in the
field of optics and
illuminating
DIN 5031-2 engineering - Part Active
2: Evaluation of
radiation by
different
detectors
Physics of
radiation in the
field of optics and
illuminating
engineering - Part
DIN 5031-3 Active
3: Quantities,
symbols and
units of
illuminating
engineering
Physics of
radiation in the
field of optics and
DIN 5031-4 Active
illuminating
engineering - Part
4: Efficiencies
Physics of
radiation in the
field of optics and
DIN 5031-5 illuminating Active
engineering - Part
5: Definitions for
temperatures
Physics of
radiation in the
field of optics and
illuminating
DIN 5031-6 engineering - Part Active
6: Pupil intensity
as a measure of
retinal
illumination
Physics of
radiation in the
field of optics and
illuminating
DIN 5031-8 Active
engineering - Part
8: Definitions and
constants of
radiation physics
Physics of
radiation in the
field of optics and
illuminating
DIN 5031-9 Active
engineering - Part
9: Definitions in
the field of
luminescence
Physics of
radiation in the
field of optics and
illuminating
engineering - Part
10:
DIN 5031-10 Active
Photobiologically
effective
radiation,
quantities,
symbols and
actions
Artificial lighting -
Part 3: Lighting of
DIN 5035-3 Active
health care
premises
Artificial lighting -
Part 6:
DIN 5035-6 Active
Measurement
and evaluation
Artificial lighting -
Part 7: Lighting of
DIN 5035-7 interiors with Active
visual displays
work stations
Artificial lighting -
Part 8: Workplace
luminaries -
DIN 5035-8 Active
Requirements,
recommendations
and proofing
Clamp strength
DIN 5117 Active
for woodworking
Other org
DIN Title Status DIN replacement
replacement
DIN 5145 Plane irons for Active
wood smooth and
for planes
Lockwashers and
locking plates for
DIN 5406 Active
use with rolling
bearings
Splined joints,
calculation of
DIN 5466-1 load capacity - Active
Part 1: general
basis
Signs in
DIN 5474 mathematical Withdrawn DIN 5473
logic
Complex
DIN 5475-1 quantities; Withdrawn DIN 5483-3
nomenclature
Time-dependent
quantities - Part
DIN 5483-1 Active
1: Terms for the
time-dependency
Time-dependent
DIN 5483-2 quantities - Part Active
2: Letter symbols
Time-dependent
quantities - Part
3: Complex
DIN 5483-3 representation of Active
sinusoidal time-
dependent
quantities
Notation of
DIN 5486 Withdrawn DIN 1303
matrices
Fourier-, Laplace-
and
DIN 5487 Z-transformation; Active
symbols and
concepts
Logarithmic
quantities and
units - Part 2:
DIN 5493-2 Logarithmic Active
ratios, levels in
nepers and
decibels
Fire test to
DIN 5510-2 railway Active
components
Compressed air
equipment for rail
vehicles -
DIN 5590 Pressure vessels Active
made of steel -
Dimensions,
designation
Spherical
washers
DIN 6319 Active
and conical
seats
Parallel
Pins,
DIN 6325 Hardened; Withdrawn DIN EN ISO 8734 ISO 8734
Tolerance
Zone m6
Washers for
DIN 6340 clamping Active
devices
Paper and
paper board
DIN 6738 Active
- Lifespan
classes
Technical
DIN 6776 drawings, Withdrawn DIN EN ISO 3098 ISO 3098
labeling
Toothed
DIN 6797 lock Withdrawn
washers
Serrated
DIN 6798 lock Withdrawn
washers
Lock
washers
DIN 6799 (retaining Active
washers) for
shafts
Bright Key
Steel;
Dimensions,
DIN 6880 Active
Permissible
Variations,
Weights
Drive Type
Fastenings
without
Taper
Action –
DIN 6885-1 Part 1: Active
Parallel
Keys,
Keyways,
Deep
Pattern
Drive Type
Fastenings
without
Taper
Action –
Part 3:
DIN 6885-3 Parallel Active
Keys,
Shallow
Pattern,
Dimensions
and
Application
Screw and
DIN 6900 Washer Withdrawn DIN EN 10644 EN 10644
Assemblies
Tapping
screw and
DIN 6901 Withdrawn DIN EN 10510 EN 10510
washer
assemblies
Plain
washers for
DIN 6902 screw and Withdrawn DIN EN 10673 EN 10673
washer
assemblies
Plain
washers for
tapping
DIN 6903 Withdrawn DIN EN 10669 EN 10669
screw and
washer
assemblies
Hexagon
socket head
cap screws
DIN 6912 Active
with center,
with low
head
Round
washers for
high-
DIN 6916 Withdrawn
strength
structural
steel bolting
Hexagon
DIN 6921 Withdrawn DIN EN 1665 EN 1665
flange bolts
Hexagon
flange bolts
DIN 6922 with Withdrawn DIN EN 1665 EN 1665
reduced
shank
Hexagon
DIN 6923 nuts with Withdrawn DIN EN 1661 EN 1661
flange
Prevailing
torque type
hexagon DIN EN ISO 7040, ISO 7040,
DIN 6924 Withdrawn
nuts with DIN EN ISO 10512 ISO 10512
nonmetallic
insert
Prevailing
torque type
DIN EN ISO 7042, ISO 7042,
DIN 6925 all-metal Withdrawn
DIN EN ISO 10513 ISO 10513
hexagon
nuts
Prevailing
torque type
hexagon
nuts with DIN EN 1663, DIN EN ISO 7043 (modified), ISO
DIN 6926 Withdrawn
flange and 1666 12125 (modified)
with non-
metallic
insert
Prevailing
torque type
DIN EN 1664, DIN EN ISO 7044 (modified),
DIN 6927 all-metal Withdrawn
1667 ISO 12126 (modified)
nuts with
flange
Cold
bending of
DIN 6935 Active
flat rolled
steel
Pan head
screws with
type H or
DIN
type Z cross Active
7045
recess -
product
grade A
Saw blades
DIN
for web Active
7245
saws
Spiral Pins;
DIN
Heavy Duty Withdrawn DIN EN ISO 8748 ISO 8748
7344
Type
Spring-Type
Straight
DIN
Pins; (Roll Withdrawn DIN EN ISO 13337 ISO 13337
7346
Pins) Light-
weight Type
Plain
Washers for
DIN Bolts with
Active
7349 Heavy
Clamping
Sleeves
Thread
rolling
screws for
DIN metric ISO
Withdrawn ISO 7085
7500-1 thread - Part
1: Types,
designation,
requirements
Thread
rolling
screws for
ISO metric
DIN
thread; Active
7500-2
guideline
values for
hole
diameters
Hexagon
head and
slotted head
thread
DIN
cutting Active
7513
screws -
Dimensions,
requirements
and testing
Cross
recessed
head thread
DIN cutting
Active
7516 screws -
Dimensions,
requirements
and testing
Diving
accessories
DIN
for skin Withdrawn
7875
divers;
terminology
Diving
accessories
for skin
DIN divers;
Withdrawn
7876 flippers.
dimensions.
requirements
and testing
Diving
accessories
for skin
DIN divers;
Withdrawn
7877 diver"s
masks.
requirements
and testing
Diving
accessories
for skin
divers;
DIN
snorkel; Withdrawn
7878
technical
requirements
of safety,
testing
Other org
DIN Title Status DIN replacement
replacement
DIN Cross Withdrawn DIN EN ISO 4757 ISO 4757
7962 recesses for
screws;
(modified
version of
ISO 4757)
Threads and
thread ends
for tapping
DIN
screws Withdrawn DIN EN ISO 1478 ISO 1478
7970
(modified
version of
ISO 1478)
Slotted pan
DIN
head tapping Withdrawn DIN ISO 1481 ISO 1481
7971
screws
Slotted
DIN countersunk
Withdrawn DIN ISO 1482 ISO 1482
7972 head tapping
screws
Slotted
raised
DIN
countersunk Withdrawn DIN ISO 1483 ISO 1483
7973
head tapping
screws
Taper Pins
with Thread
DIN Ends and
Withdrawn DIN EN 28737 ISO 8737
7977 Constant
Point
Lengths
Taper Pins
DIN
with Internal Withdrawn DIN EN 28737 ISO 8736
7978
Thread
Parallel Pins
DIN DIN EN ISO 8733, ISO 8733,
with Internal Withdrawn
7979 DIN EN ISO 8735 ISO 8735
Thread
Spring lock
washers with
DIN
square ends Withdrawn
7980
for cheese
head screws
Cross
recessed
DIN
pan head Withdrawn DIN ISO 7049 ISO 7049
7981
tapping
screws
Cross
recessed
DIN
countersunk Withdrawn DIN ISO 7050 ISO 7050
7982
head tapping
screws
Other org
DIN Title Status DIN replacement
replacement
DIN Countersunk Withdrawn DIN ISO 7051 ISO 7051
7983 (Flat) Head
Tapping
Screws with
Cross
Recess
Hexagon
socket head
DIN
cap screws Active
7984
with low
head
Cross
recessed
DIN
raised Withdrawn DIN EN ISO 7045 ISO 7045
7985
Phillips Pan
head screws
Washers for
steel
DIN
structures - Active
7989-1
Product
grade C
Washers for
steel
DIN
structures - Active
7989-2
Product
grade A
Hexagon
socket
DIN
countersunk Withdrawn DIN EN ISO 10642 ISO 10642
7991
head cap
screws
Polyethylene
DIN 8074 (PE) pipes – Active
Dimensions
Polyethylene
(PE) pipes -
PE 63, PE 80,
PE 100, PE-
DIN 8075 Active
HD - General
quality
requirements,
testing
Polypropylene
(PP-R) Pipes
-PN 20, PN25
PP-R -
DIN 8077/8078 Active
General
quality
requirements,
testing
Brazing and
Braze Weld
Filler Metals;
Copper Base
Brazing
DIN 8513-1 Alloys; Withdrawn DIN EN 1044 EN 1044
Composition,
Use,
Technical
Conditions of
Delivery
Brazing and
Braze Weld
Filler Metals;
Silver-bearing
Brazing Alloys
with less than
DIN 8513-2 20% by wt. Withdrawn DIN EN 1044 EN 1044
Silver;
Composition,
Use,
Technical
Conditions of
Delivery
Brazing filler
metals; silver
brazing filler
metals
containing not
less than 20%
DIN 8513-3 Withdrawn DIN EN 1044 EN 1044
of silver;
composition,
application,
technical
delivery
conditions
Other org
DIN Title Status DIN replacement
replacement
DIN 8513-4 Brazing and Withdrawn DIN EN 1044 EN 1044
Braze Weld
Filler Metals;
Aluminium-
Base Brazing
Alloys;
Composition,
Use,
Technical
Conditions of
Delivery
Brazing filler
metals; Nickel
base filler
metals for
high
temperature
DIN 8513-5 Withdrawn DIN EN 1044 EN 1044
brazing;
Application,
composition,
technical
delivery
conditions
Manufacturing
processes -
DIN 8580 Terms and Active
definitions,
division
Narrow band
saw blades
DIN 8806-1 for Active
woodworking;
dimensions
Defects in
Metallic
Solder Joints;
Brazing Joints
and High-
DIN EN ISO
DIN 8515 temperature Withdrawn
18279:2004-04
Solder Joints;
Classification,
Designations,
Explanatory
Notes
Plain
washers
with DIN EN ISO 7093-1, DIN EN
DIN 9021 Withdrawn ISO 7093-1, ISO 7093-2
large ISO 7093-2
outside
diameter
Other org
DIN Title Status DIN replacement
replacement
Food
hygiene
- Lamps
for the
DIN 10504 lighting Withdrawn
of meat
and
meat
products
Other org
DIN Title Status DIN replacement
replacement
Hygenic
DIN 11851
Unions
Laboratory
furniture; safety
cabinets for
microbiological
DIN 12950-1 and Withdrawn
biotechnological
work; safety
requirements,
tests
Laboratory
furniture; safety
cabinets for
microbiological
and
biotechnological
DIN 12950-2 work; Withdrawn
containment of
class 1 and
class 2
cabinets,
microbiological
test
Laboratory
furniture; safety
cabinets for
microbiological
DIN 12950-
and Withdrawn
10
biotechnological
work;
requirements
and testing
Thermal solar
systems and
components -
DIN 12975-1 Solar collectors
- Part 1:
General
requirements
Thermal solar
systems and
components -
DIN 12975-2
Solar collectors
- Part 2: Test
methods
Thermal solar
systems and
components -
DIN 12976-1 Factory made
systems - Part
1: General
requirements
Other org
DIN Title Status DIN replacement
replacement
Division of
hospitals into
functional
DIN 13080 Active
areas and
functional
sections
Supply
systems for
medical gases
- Part 2:
Dimensions
and allocation
of probes and
DIN 13260-2 gas-specific Active
connection
points for
terminal units
for
compressed
medical gases
and vacuum
Packaging -
Requirements
for packaging
recoverable
through
composting
and
DIN 13432 Active DIN EN 13432
biodegradation
- Test scheme
and evaluation
criteria for the
final
acceptance of
packaging
Workpiece
DIN ISO 13715(2000
DIN 13715 corners and Active
–12)
edges
Fire
precaution
regulation -
Part 1:
General and
DIN 14096-1 Active
part A
(placard);
rules for
drafting and
placarding
Fire
precaution
regulation -
Part 2: Part B
(for persons
without
DIN 14096-2 special tasks Active
of fire
prevention
and fire
fighting);
rules for
drafting
Fire
precaution
regulation -
Part 3: Part C
(for persons
with special
DIN 14096-3 Active
tasks of fire
prevention
and fire
fighting);
rules for
drafting
Water pool
DIN 14210 Active
for firefighting
Ultrasonic
DIN 14236 domestic gas Active
meters
Portable fire
extinguishers
DIN 14406-4 Active
- Part 4:
Maintenance
Trailers for
firefighting
purposes,
DIN 14503 Withdrawn DIN 14521
two-wheeled;
general
requirements
Rescue
service
vehicles -
Vehicles for
DIN 14507 Active
roller
containers -
General
requirements
Trailers for
DIN 14520 portable fire Withdrawn
pumps
Firefighting -
Trailer with
DIN 14521 removable Active
foam-water
monitor
Fire fighting
vehicles -
Part 5: Group
pumping
appliance LF
DIN 14530-5 10/6, Group Active
pumping
appliance for
rescue
operations
HLF 10/6
Fire fighting
vehicles -
Part 11:
Group
pumping
appliance LF
DIN 14530-11 Active
20/16, Group
pumping
appliance for
rescue
operations
HLF 20/16
Fire fighting
vehicles -
Part 16:
DIN 14530-16 Active
Pumping
appliance
TSF
Fire fighting
vehicles -
Part 21:
Pump water
DIN 14530-21 Active
tanker TLF
20/40, Pump
water tanker
TLF 20/40-SL
Fire fighting
vehicles -
DIN 14530-22 Active
Part 22: TLF
16/24-TR
Fire fighting
vehicles -
Part 24:
DIN 14530-24 Small Active
pumping
appliance
KLF
Fire fighting
vehicles -
Part 25:
DIN 14530-25 Active
Pumping
appliance
STLF 10/6
Vehicles
carrying tools
and gears -
DIN 14555-1 Active
Part 1:
General
requirements
Vehicles
carrying tools
and gears -
DIN 14555-3 Active
Part 3:
Emergency
tender RW
Vehicles
carrying tools
and gears -
DIN 14555-12 Part 12: Active
Damage
control tender
GW-G
Vehicles
carrying tools
and gears -
DIN 14555-22 Active
Part 22: GW-
L2 for logistic
tasks
Fire hose
DIN 14565 tender; Type Withdrawn
SW 2000-TR
Turntable
ladders and
similar fire
fighting
vehicles;
DIN 14701-1 Withdrawn DIN EN 1777 EN 1777
Purpose,
concepts,
safety
equipment,
requirements
Turntable
ladders and
similar fire
fighting DIN EN 14043, DIN EN
DIN 14701-2 Withdrawn EN 14043, EN 14044
vehicles; 14044
Turn table
ladders,
engine driven
Turntable
ladders and
similar fire
DIN 14701-3 fighting Withdrawn DIN EN 1777 EN 1777
vehicles;
Rescue
baskets
Turntable
ladder DL
DIN 14702 Active
16-4, hand
operating
Trailer
DIN 14703 Ladder AL Active
16-4
Hook ladder,
manufactured
DIN 14710-1 using wood; Withdrawn DIN EN 1147 EN 1147
with hinged
hook
Hook light
DIN 14710-3 Withdrawn
metal ladder
Scaling
ladder; made
DIN 14711-2 Withdrawn DIN EN 1147 EN 1147
from light
metal
Scaling
ladder;
DIN 14711-3 socket rungs Withdrawn DIN EN 1147 EN 1147
and socket
parts
Folding
DIN 14713 Withdrawn DIN EN 1147 EN 1147
ladder
Three piece
extension
DIN 14715-1 Withdrawn DIN EN 1147 EN 1147
ladder made
from wood
Three piece
extension
DIN 14715-2 Withdrawn DIN EN 1147 EN 1147
ladder; made
of light metal
Other org
DIN Title Status DIN replacement
replacement
Cranes; steel
structures;
DIN 15018-2 Active
principles of design
and construction
Warehouse
systems with
guided industrial
trucks;
DIN 15185-1 Active
requirements on
the ground, the
warehouse and
other requirements
Warehousesystems
with powered
industrials trucks;
code of practice for
the protection of
DIN 15185-2 persons when Active
operating with
trucks in narrow
aisles; safety
requirements,
testing
Film 70 mm;
DIN 15721 Active
projection reel
DIN 16000 to DIN 16999
Other org
DIN Title Status DIN replacement
replacement
Classification
DIN 16518 Active
of types
Cross-linked
high-density
polyethylene
(PE-X) pipes
DIN 16892 Active
- General
quality
requirements
and testing
Cross-linked
high-density
polyethylene
DIN 16893 Active
(PE-X) pipes
–
Dimensions
Seamless
Tubes of heat
DIN 17175 Withdrawn DIN EN 10216-2
Resistant
Steels
Steels For
Quenching
And DIN 10083-1
DIN 17200 Tempering - Superseded DIN 10083-2
Technical DIN 10083-3
Delivery
Conditions
Heat
Resisting and
Highly Heat
Resisting
DIN 17240 Withdrawn DIN EN 10269
Materials for
Bolts and
Nuts; Quality
Specifications
Materials for
permanent
DIN 17410 magnets: Active
Technical
conditions
Resistance
DIN 17471 Active
alloys
House
service
connections
DIN 18012 Active
facilities -
Principles for
planning
Recesses for
meter boards
DIN 18013 Active
(electric
meters)
Foundation
earth
electrode -
DIN 18014 Active
General
planning
criteria
Electrical
installations
in residential
DIN 18015-1 buildings - Active
Part 1:
Planning
principles
Electrical
installations
in residential
buildings -
DIN 18015-2 Part 2: Active
Nature and
extent of
minimum
equipment
Electrical
installations
in residential
buildings -
DIN 18015-3 Part 3: Active
Wiring and
disposition of
electrical
equipment
Domestic
kitchens,
bathrooms
DIN 18022 Withdrawn
and WCs;
design
principles
Construction
of accessible
buildings -
Part 2:
Publicly
DIN 18024-2 Active
accessible
buildings and
workplaces,
design
principles
Stairs in
buildings -
Terminology,
DIN 18065 Active
measuring
rules, main
dimensions
Construction
contract
procedures
(VOB) - Part
C: General
technical
specifications
DIN 18379 in Active
construction
contracts
(ATV) -
Installation of
air
conditioning
systems
Contract
procedures
for building
works - Part
C: General
technical
specifications
for building
works; Low-
DIN 18382 Active
voltage
installation
and medium-
voltage
installation
with nominal
voltages up
to including
36 kV
Steel
structures -
DIN EN 1993
DIN 18800-1 Part 1: Withdrawn
DIN EN 1090
Design and
construction
Steel
structures -
Part 2:
Analysis of
safety
DIN 18800-2 Withdrawn DIN EN 1993
against
buckling of
linear
members
and frames
Steel
structures -
Part 3:
Analysis of
DIN 18800-3 Withdrawn DIN EN 1993
safety
against
buckling of
plates
Steel
structures -
Part 4:
Analysis of
DIN 18800-4 Withdrawn DIN EN 1993
safety
against
buckling of
shells
Steel
structures -
Part 5:
Composite
DIN 18800-5 structures of Withdrawn DIN EN 1994
steel and
concrete -
Design and
construction
Control
DIN V 19222 technology – Active
Terminology
Measurement
and control;
terminology
DIN 19225 Active
and
classification
of controllers
Control
technology -
Part 1:
DIN 19226-1 Active
General terms
and
definitions
Control
technology -
Part 2: Terms
and
DIN 19226-2 Active
definitions;
dynamic
systems
behaviour
Control
technology -
Part 3: Terms
and
DIN 19226-3 Active
definitions of
switching
systems
behaviour
Control
technology -
Part 4: Terms
DIN 19226-4 and Active
definitions of
control
systems
Control
technology -
DIN 19226-5 Part 5: Active
Functional
terms
Control
technology -
Part 6: Terms
and
DIN 19226-6 Active
definitions of
functional and
constructional
units
Control
technology;
graphical
symbols and
identifying
DIN 19227-2 letters for Active
process
control
engineering;
representation
of details
Measurement
DIN 19226-3, DIN
and control;
19226-4,
DIN 19237 control Withdrawn
DIN 19226-5, DIN
engineering
19226-6
vocabulary
Control
technology;
graphical
symbols and
identifying
letters for
DIN 19227-1 Withdrawn DIN EN 62424
process
control
engineering;
symbolic
representation
for functions
Control
technology;
graphical
symbols and
identifying
DIN 19227-2 letters for Active
process
control
engineering;
representation
of details
Hydraulic
steel
structures -
DIN 19704-1 Part 1: Active
Criteria for
design and
calculation
Hydraulic
steel
structures -
DIN 19704-2 Active
Part 2: Design
and
manufacturing
Hydraulic
steel
structures -
DIN 19704-3 Active
Part 3:
Electrical
equipment
Fluid
technology -
DIN 20066 hose lines,
dimensions,
specifications
Explosives
DIN 20163
work
Hammer and
chisel signs
DIN 21800
(mining
symbol)
Mining
DIN 21908 crevice work;
colours
Conveyor belt
for bulk
material,
DIN 22101
fundamentals,
analysis and
design
Arrangements
for belt
DIN 22107
conveyor
rollers
Rollers:
dimensions,
DIN 22112
specifications,
testing
Seat leathers
for the mining
DIN 23307 industry
(miner's
apron)
Clothing for
the mining
industry –
DIN 23342
men's vest
with 1/4
sleeves
Clothing for
the mining
industry –
DIN 23345 men's
underpants
1/1 length
(Long Johns)
Ventilation
and air
conditioning
- folded and
DIN 24190 Withdrawn
welded
rectangular
sheet metal
ducts
Hydraulic
valves;
mounting
surfaces
and
DIN 24340-2 Active
connecting
plates for
directional
control
valves
Other org
DIN Title Status DIN replacement
replacement
Ductile iron
pressure
pipes with
socket with
cement-
mortar
DIN 28610-1 lining for Withdrawn DIN EN 545, DIN EN 969 EN 545, EN 969
gas and
water
pipelines;
dimensions
and
masses
Ductile iron
pressure
pipes with
socket for
gas and
water
pipelines
rated for
DIN 28610-2 Withdrawn DIN EN 969 EN 969
pressures
over 4 bar
up to and
including
16 bar;
dimensions
and
masses
DIN 30000 to DIN 39999
Other org
DIN Title Status DIN replacement
replacement
Roller
contact
tipper
vehicles,
roller
containers
- Part 1:
Roller
DIN 30722-1 contact Active
tipper
vehicles
up to 26 t,
roller
containers
type 1570
made
from steel
Roller
contact
tipper
vehicles,
roller
containers
- Part 2:
Roller
DIN 30722-2 contact Active
tipper
vehicles
up to 32 t,
roller
containers
type 1570
made
from steel
Roller
contact
tipper
vehicles,
roller
containers
- Part 3:
Roller
DIN 30722-3 contact Active
tipper
vehicles
up to 12 t,
roller
containers
type 900
made
from steel
Roller
containers
for the
DIN 30722-4 Active
transport
on road
and rail
DIN 31000 to DIN 31999
Other org
DIN Title Status DIN replacement
replacement
Conversion
of the
DIN 31635 Active
Arabic
alphabet
Tri-Clamp
DIN 32676 Active
Fittings[2]
Frequency and
DIN 40015 Active
wave bands
Road vehicles;
degrees of
protection (IP-code);
DIN 40050-9 protection against Active
foreign objects;
water and contact;
electrical equipment
Graphical symbols
DIN 40101-1 for use on Withdrawn
equipment
Graphical symbols
for use on
equipment;
DIN 40101-2 graphical symbols Active
from ISO 7000 for
electrical
engineering
Electric power
technology - Current
DIN 40108 systems - Concepts, Active
quantities, letter
symbols
Quantities used in
alternating current
DIN 40110-1 Active
theory - Part 2: Two-
line circuits
Quantities used in
alternating current
DIN 40110-2 Active
theory - Part 2:
Multi-line circuits
Telecommunications
DIN 40146-1 - Part 1: Basic Active
concepts
Transmission
systems and two-
DIN 40148-1 Active
ports; concepts and
quantities
Transmission
systems and two-
DIN 40148-2 ports; symmetry Active
characteristics of
linear two-ports
Other org
DIN Title Status DIN replacement
replacement
DIN 40148-3 Transmission Active
systems and two-
ports; measures for
attenuation
Nominal value,
limiting value, rated
DIN 40200 Active
value, rating -
concepts
Electrical
communication
DIN 41215 engineering; Withdrawn
electromagnetic
relays, definitions
Electro Sheets;
DIN 41301 Magnetic Materials Withdrawn
for Transformers
Small transformers
and chokes; strip-
wound cut cores;
DIN 41309-1 types SM, SE, SU, Withdrawn
SG and S3U;
dimensions
materials
Small transformers
and chokes; strip-
wound cut cores;
technical conditions
DIN 41309-2 Withdrawn
of delivery for one
phase applications;
types SM, SE, SU
and SG
Small transformers
and chokes; strip-
wound cut cores;
DIN 41309-3 technical conditions Withdrawn
of delivery for three
phase applications;
type S3U
Nominal values of
DIN 41426 resistors and Withdrawn DIN IEC 60063 IEC 60063
capacitors
Circular connectors
for radio and
associated sound
DIN 41524 Withdrawn
equipment three
and five-pole
connectors
Two piece
connectors for
DIN 41612-1
printed circuits, grid Withdrawn DIN EN 60603-2 EN 60603-2
S1
2,54 mm (0,1 in);
general allusions
Two-part connectors
for printed boards;
DIN 41612-2 grid 2,54mm; Withdrawn DIN EN 60603-2 EN 60603-2
dimensions of types
B, C and D
Two-part connectors
for printed boards;
DIN 41612-4 grid 2,54mm, Withdrawn DIN EN 60603-2 EN 60603-2
dimensions of type
H
Two-part connectors
for printed boards;
DIN 41612-5 grid 2,54mm; Withdrawn DIN EN 60603-2 EN 60603-2
ratings,
requirements, tests
Two-part connection
for printed boards;
DIN 41612-6 grid 2.54mm; Withdrawn DIN EN 60603-2 EN 60603-2
dimensions of types
Q, R and S
Two-part connectors
for printed boards;
DIN 41612-7 grid 2,54 mm; Withdrawn DIN EN 60603-2 EN 60603-2
dimensions of types
U and V
Two-part connectors
for printed boards;
DIN 41612-8 grid 2.54 mm; Withdrawn DIN EN 60603-2 EN 60603-2
dimensions of type
M
Two-part connectors
for printed boards;
grid 2.54 mm;
DIN 41612-8
dimensions of type Withdrawn DIN EN 60603-2 EN 60603-2
S1
M; survey of special
contracts for use
with type M
Two-part connectors
DIN 41612- for printed boards;
Withdrawn DIN EN 60603-2 EN 60603-2
10 grid 2,54mm;
gauges
Two-part connectors
DIN 41612- for printed boards;
Withdrawn DIN 41612-9
102 dimensions for type
X
Two-part connectors
DIN 41612- for printed boards;
Withdrawn DIN 41612-8
103 dimensions of type
M
Thyristors,
DIN 41786 Withdrawn
definitions
Semiconductor
devices and
DIN 41855 integrated circuits; Withdrawn
kinds of devices and
general terms
Semiconductor
devices and
integrated circuits;
DIN 41855-2 optoelectronic Withdrawn
semiconductor
devices; terms and
definitions
Cases 10 A 3 and
10 B 3 for
DIN 41868 semiconductor Withdrawn
devices; main
dimensions
Case 23 A 3 for
semiconductor
DIN 41869-1 Withdrawn
devices; main
dimensions
Cases 34 A 2 and
34 A 3 for
DIN 41869-2 semiconductor Withdrawn
devices; main
dimensions
Case 11 A 3 and 11
B 3 for
DIN 41869-3 semiconductor Withdrawn
devices; main
dimensions
Case 12 A 3 for
semiconductor
DIN 41869-4 Withdrawn
devices; main
dimensions
Case 13 A 3 for
semiconductor
DIN 41869-5 Withdrawn
devices; main
dimensions
Case 14 A 3 for
semiconductor
DIN 41869-6 Withdrawn
devices; main
dimensions
Other org
DIN Title Status DIN replacement
replacement
DIN 41869-7 Case type 15 for Withdrawn
semiconductor
devices; main
dimensions
Cases 18 A, B and
C with 2 up to 4
terminals for
DIN 41876 Withdrawn
semiconductor
devices; main
dimensions
Terminal markings
for electrical
DIN 42400 equipment; general Withdrawn DIN EN 60445 EN 60445
rules, alphanumeric
system
Terminal markings
for power
DIN 42402 Active
transformers and
reactors
Terminal markings
DIN 42403 Withdrawn DIN IEC 61148 IEC 61148
for power converters
Totally enclosed
fan-cooled three-
phase induction
motors squirrel-
cage, type IM B 3,
DIN 42673-1 Withdrawn
with rolling bearing;
mounting
dimensions and
relationship frame
sizes-output ratings
Totally enclosed
fan-cooled three-
phase induction
motors with squirrel-
cage, type IM B 3,
DIN 42673-2 with rolling bearings; Active
relationship frame
sizes - output
ratings for type of
protection increased
safety "e"
Totally enclosed
fan-cooled
alternating-current
polyphase motors
DIN 42673-4 with squirrel-cage, Active
design B3, with ball
bearings, maximum
envelope
dimensions
Measurement and
control -
Measurement and
DIN 43700 control instruments Withdrawn DIN IEC 61554 IEC 61554
for panel mounting -
Nominal front- and
cut-out-dimensions
Electrical measuring
instruments; direct
acting indicating
DIN 43780 Withdrawn DIN EN 60051-1 EN 60051-1
electrical measuring
instruments and
their accessories
Electricity meters,
tariff time switches
and ripple control
receivers;
DIN 43856 Active
connection
diagrams, terminal
marking, circuit
diagrams
Electricity meters -
Part 2: Marking of
auxiliary terminals
DIN 43856-2 Active
for tariff devices
according to IEC-
Report 61354:1995
Meter mounting
boards; dimensions
DIN 43870-1 Active
based on a grid
system
Meter mounting
DIN 43870-2 boards; functional Active
area
Meter panels;
DIN 43870-3 Active
wirings
Meter mounting
boards; dimensions
DIN 44070-1 Active
based on a grid
system
Meter mounting
DIN 44070-2 boards; functional Active
area
Meter panels;
DIN 44070-3 Active
wirings
Thermistors; PTC,
DIN 44080 technical terms and Withdrawn
tests
Information
processing -
DIN 44300-1 Withdrawn
Concepts - General
terms
Information
processing -
DIN 44300-2 Concepts - Withdrawn
Representation of
data
Information
processing -
DIN 44300-3 Withdrawn
Concepts - Data
structures
Information
processing -
DIN 44300-4 Withdrawn
Concepts –
Programming
Information
processing -
Concepts -
DIN 44300-5 Withdrawn
Components of
digital computer
systems
Information
DIN 44300-6 processing - Withdrawn
Concepts – Storage
Information
DIN 44300-7 processing - Withdrawn
Concepts – Times
Information
processing -
DIN 44300-8 Concepts - Withdrawn
Processing
functions
Information
processing -
DIN 44300-9 Concepts - Process Withdrawn
relations and modes
of operation
Circular connectors
for radio and
DIN 45322 associated sound Withdrawn DIN EN 60130-9 EN 60130-9
equipment; six-pole
connectors
Measuring
apparatus for
DIN 45507 frequency variations Withdrawn DIN IEC 60386 IEC 60386
in sound recording
equipment
Disk record
reproducing
equipment;
directives for
measurements,
markings and audio
DIN 45539 frequency Withdrawn DIN IEC 60098 IEC 60098
connections,
dimensions of
interchangeable
pickups,
requirements of play
back amplifiers
Microphones;
DIN 45596 Withdrawn
phantom powering
Grain-oriented
magnetic steel and
DIN 46400-3 Withdrawn DIN EN 10107 EN 10107
strip technical
conditions
Cords for
telecommunication;
DIN 47100 code of insulated Withdrawn
conductors, colour
of sheath
Lightning protection
system;
Arrangement of
DIN 48803 Withdrawn
components and
dimensions for
mounting
Lightning protection
DIN 48830 Withdrawn
system; Description
Testing of
floor
coverings;
determination
of the anti-slip
DIN 51097 properties: Withdrawn DIN 51130
wet-loaded
barefoot
areas; walking
method; ramp
test
Testing of
floor
coverings;
determination
of the anti-slip
properties:
DIN 51130 workrooms Withdrawn DIN 51097
and fields of
activities with
slip danger,
walking
method - ramp
test
Lubricants;
Lubricating
DIN 51501 Oils L-AN; Withdrawn
Minimum
Requirements
Testing of
particleboards;
determination
DIN 52368 of Withdrawn DIN EN 717-2 EN 717-2
formaldehyde
emission by
gas analysis
Paints and
varnishes -
Determination
of the drying
DIN 53150 stage of Active
coatings
(modified
Bandow-Wolff
method)
Testing of
combustible
materials;
DIN 53438 Active
response to
ignition by
small flame
Testing of
DIN 53452 Plastics; Withdrawn DIN EN ISO 178 ISO 178
Flexural Test
Testing of
combustible
materials;
DIN 54836 Active
determination
of ignition
temperature
Determination
of burning
DIN 54837 behaviour Active
using a gas
burner
Machine tools;
symbols;
DIN 55003-3 numerically Withdrawn
controlled
machine tools
Measuring
Method for
determination
DIN 58145 of solarization Active
effect of fused
silica optical
fibers
Surgical
implants;
DIN 58810 threads for Withdrawn
bone screws
and nuts
Thread
connection for
DIN 58888 Withdrawn DIN ISO 8038-1 ISO 8038-1
microscope
objectives
DIN ISO 53438
Information
processing;
switching
DIN 66000 algebra, Active
mathematical
signs and
symbols
Information
processing;
DIN 66001 graphical Active
symbols and
their application
Information
processing;
handwriting of
DIN 66002 Active
the digit 0 and
of the upper
case letter O
Information
DIN 66003 technology - Active
7-bit code
Information
processing -
Coding on data
media - Part 1:
DIN 66004-1 Representation Active
of 7-bit code
character sets
on punched
tape 25
Information
processing -
Coding on data
media - Part 2:
Representation
DIN 66004-2 Active
of 7-bit coded
and 8-bit coded
character sets
on punched
cards
Information
processing -
Coding on data
media - Part 3:
Representation
DIN 66004-3 Active
of 7-bit coded
and 8-bit coded
character sets
on magnetic
tape 12
Information
processing -
Coding on data
media - Part 5:
Representation
DIN 66004-5 Active
of 7-bit coded
and 8-bit coded
set on media-
flexible disk
cartridge
Information
processing;
representation
of packed
numerics and
DIN 66005 Active
binary data
recorded on 9
tracks on
magnetic tape
12
Presentation of
ALGOL/ALCOR
DIN 66006 programs on Withdrawn
paper tape and
punch cards
Font A for
optical
character
DIN 66008-1 recognition; Active
characters and
nominal
dimensions
Font A for
optical
character
recognition;
DIN 66008-6 characters and Active
nominal
dimensions;
extension of the
character set
Font B for
optical
DIN 66009 character Withdrawn
recognition;
character
Functional
requirements
for the interface
between data
terminal
DIN 66020-1 equipment and Active
data circuit-
terminating
equipment -
Part 1: General
application
List of
definitions for
interchange
circuits
between data
terminal
DIN 66020-2 equipment Active
(DTE) and data
circuit-
terminating
equipment
(DCE) in public
data networks
Data
transmission;
interface
between data
circuit-
DIN 66020-4 terminating Active
equipment
(DCE) and data
terminal
equipment
(DTE)
Data
transmission;
interface
between data
circuit-
DIN 66021-1 terminating Active
equipment
(DCE) and data
terminal
equipment
(DTE)
Interface
between data
terminal
equipment
(DTE) and data
circuit-
terminating
DIN 66021-2 equipment Active
(DCE) for
synchronous
transmission on
group band
circuits at
48,000 bits per
second
Numerical
control of
DIN 66025-1 machines, Active
format; general
requirements
Industrial
automation;
numerical
control of
DIN 66025-2 machines; Active
format,
preparatory and
miscellaneous
functions
Information
processing;
DIN 66027 programming Withdrawn
language
FORTRAN
Programming
of numerically
controlled
machines;
CLDATA; minor
DIN 66215-2 Active
elements of
type 2000
records (post-
processor
commands)
Information
processing;
DIN 66253-2 programming 1998
language
PEARL
Information
processing;
DIN 66234 Active
programming
language PL/I
Information
processing;
DIN 66255 Active
programming
language PL/I
Information
processing;
DIN 66256 programming Withdrawn
language
Pascal
Numerical
control of
DIN 66257 Withdrawn DIN ISO 2806 ISO 2806
machines;
concepts
Interfaces and
basic data link
control
procedures for
DIN 66258-1 Withdrawn
data
communication;
C S-interface, V
S-interface
Information
processing;
Nassi-
DIN 66261 Active
Shneiderman
flowchart
symbols
Industrial
automation
systems and
integration -
Multiprocessor
DIN 66264-1 Active
Control System
for Industrial
Machines
(MPST) - Part
1: Parallel bus
Multiprocessor
control system
for industrial
machines
(MPST);
DIN 66264-2 Active
industrial
automatics;
rules for
information
interchange
Information
DIN 66303 technology - 8 Active
bit code
Industrial
automation;
Computer
Aided Design;
DIN V 66304 Active
format for the
exchange of
standard parts
data
Local and
Metropolitan
Area Networks;
DIN 66325-2 Withdrawn ISO 8802-2
LLC; identical
with ISO
8802-2:1989
Three-part
standard
regarding the
seven security
DIN 66399 Active
levels of paper
shredders;
replaces DIN
32757
Project
controlling;
DIN 69901 project Active
management;
concepts
Lubricating
DIN 71412 nipples; cone Active
type
Lead storage
batteries;
starter
batteries for
DIN 72311-1 motorcycles, Active
nominal
capacities,
main
dimensions
Lead storage
batteries;
starter
DIN 72311-4 batteries, Active
terminals, vent
plugs and filler
openings
Lead storage
batteries;
starter
DIN 72311-8 batteries for Active
motor cycles
and passenger
cars
Lead storage
batteries;
starter
batteries for
starting,
DIN 72311-13 lighting and Active
ignition, 12 V,
27, 36, 45 and
54 Ah, for
lateral basic
fastening 10,5
Lead storage
batteries;
starter
batteries for
starting,
DIN 72311-16 lighting and Active
ignition, 12 V,
27, 36, 45, 54
and 63 Ah, for
lateral basic
fastening 19
Lead storage
batteries;
starter
DIN 72311-17 batteries, Active
protective
covering for
terminal
Other org
DIN Title Status DIN replacement
replacement
DIN 72311-18 Lead storage Active
batteries;
starter
batteries with
basic fastening
10,5 for
passenger
cars and
commercial
vehicles;
nominal
capacities,
main
dimensions
Lead storage
batteries;
starter
batteries for
commercial
DIN 72311-20 Active
vehicles;
nominal
capacities and
main
dimensions
Lead storage
batteries;
starter
batteries with
10,5 basic
fastening lugs
DIN 72311-21 Active
for commercial
vehicles;
nominal
capacities and
main
dimensions
Terminal
markings for
motor vehicles;
DIN 72552-1 Active
scope,
principles,
requirements
Terminal
markings for
DIN 72552-2 Active
motor vehicles;
codes
Terminal
markings for
motor vehicles;
DIN 72552-3 examples for Active
application on
circuit
diagrams
Radio
communication
devices in
DIN 75490 motor vehicles; Active
installation
space, general
requirements
See also
◾ List of ASTM standards
◾ List of EN standards
◾ List of IEC standards
◾ List of ISO standards
References
1. DK 621.882.245 Deutsche Normen Dec. 1952 Linsensenkschrauben mit Längsschlitz
2. "What is DIN 32676? | Sanitary Fittings" (https://sanitaryfittings.us/what-is-din-32676).
sanitaryfittings.us. Retrieved 18 September 2018.
External links
◾ DIN Website, in English (https://web.archive.org/web/20110111174038/http://www.din.de/cmd?
level=tpl-home&languageid=en)
◾ DIN Fasteners in Details (http://www.deepri.com/din_specifications/index.html)
Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply.
By using this site, you agree to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark
of the Wikimedia Foundation, Inc., a non-profit organization.