Electrozi inveliti pentru sudare MMA - oteluri nealiate
Tip electrod Standard de clasificare
Compozitie Chimica % Caracteristici mecanice Dimensiune OK 43.32 SFA/AWS A5.1 - E6013 EN 499 - E42 0 RR 12 ISO 2560 - E 51 3 RR 31 C Si Mn 0,07 0,4 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta 0C 460 MPa 550 MPa 24 % 65 J 40 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 46.00 SFA/AWS A5.1 - E6013 EN 499 - E 38 0 RC 11 ISO 2560 - E 43 3 R 11 CSN 05 5010 - E 46.17 C Si Mn 0,08 0,3 0,4 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta 0C 400 MPa 510 MPa 28% 70 J 35 J 2,5 x 350 3,2 x 350 4,0 x 350 5,0 x 450 OK 48.00 SFA/AWS A5.1 - E7018 EN 499 - E42 4 B 42 H5 ISO 2560 - E51 5B 120 20H C Si Mn 0,06 0,5 1,15 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C 445 MPa 540 Mpa 29 % 140 J 70 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 48.04 SFA/AWS A5.1 - E7018 EN 499 - E 42 4 B 32 H5 ISO 2560 - E 51 5B 120 26H C Si Mn 0,06 0,5 1,1 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C 480 MPa 560 MPa 30 % 150 J 100 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 48.05 SFA/AWS A5.1 - E7018 EN 499 - E 42 4 B 42 H5 ISO 2560 - E 51 5B 120 20H C Si Mn 0,06 0,5 1,0 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C 445 MPa 540 MPa 29 % 140 J 70 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 48.15 SFA/AWS A5.1 - E7018 EN 499 - E 42 3 B 32 H5 ISO 2560 - E 51 5B 120 26 H C Si Mn 0,06 0,5 1,1 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -30C Rezilienta -40C 490 MPa 575 MPa 30 % 110 J 60 J 50 J 2,5 x 350 3,2 x 450 4,5 x 450 5,0 x 450 OK 48.60 SFA/AWS A5.1 - E 7018 EN 499 - E42 4 B 42 H5 C Si Mn 0,04 0,63 1,1 Forta alungire Forta rupere Alungire Rezilienta -40C 445 MPa 540 MPa 29 % 70 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 50.40 SFA/AWS A5.1 - E6013 EN 499 - E42 2 RB 12 CSN 05 5010 - E 50.95 C Si Mn 0,08 0,2 0,5 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -30C 440 MPa 520 Mpa 27 % 47 J 28 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 53.05 SFA/AWS A5.1 - E7016 EN 499 - E 42 4 B 22 H10 ISO 2560 E 51 5 B 21 (H) C Si Mn <0,1 0,5 1,0 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilenta -40C 470 MPa 540 MPa 28 % 150 J 80 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 53.16 SPEZIAL SFA/AWS A5.1 - E7016 EN 499 - E38 2 B 32 H10 ISO 2560 - E 51 4 B 21(H) C Si Mn 0,07 0,6 0,9 Forta alungire Forta rupere Alungire Rezilienta -20C 450 MPa 530 MPa 28 % 120 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 53.68 SFA/AWS A5.1 - E7016-1 EN 499 - E 42 5 B 12 H5 C Si Mn 0,06 0,4 1,3 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C Rezilienta -50C 420 MPa 510 MPa 26 % 150 J 80 J 47 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 53.70 SFA/AWS A5.1 - E7016-1 DIN 1913 - E 51 55 B10 EN 499 - E 42 5 B 12 H5 ISO 2560 - E 51 5 B 24 H C Si Mn 0,06 0,5 1,2 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C Rezilienta -50C 440 MPa 530 MPa 30 % 150 J 120 J 100 J 2,5 x 350 3,2 x 450 4,0 x 450 OK 55.00 SFA/AWS A5.1 - E7018-1 CSA W48 - E4918-1 CSN 05 5010 - E 55.93 EN 499 - E46 4 B 32 ISO 2560 - E 51 5B 120 26H C Si Mn 0,06 0,5 1,5 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -50C 480 MPa 590 Mpa 28 % 115 J 50 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK Femax 33.30 SFA/AWS A5.1 - E7024 EN 499 - E 42 0 RR 53 ISO 2560 - E 51 3 RR 140 34 C Si Mn 0,12 0,4 0,7 Forta alungire Forta rupere Alungire Rezilienta 0C Rezilienta -20C 420 MPa 510-610 MPa 28 % 47 J 28 J 3,2 x 450 4,0 x 450 5,0 x 450 OK Femax 33.60 SFA/AWS A5.1 - E7024 EN 499 - E 42 0 RR 53 ISO 2560 - E 51 2 RR 160 31 C Si Mn 0,12 0,4 0,7 Forta alungire Forta rupere Alungire Rezilienta 0C 450 MPa 550 MPa 28 % 55 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK Femax 33.80 SFA/AWS A5.1 - E7024 EN 499 - E 42 0 RR 73 ISO 2560 - E 51 2 RR 180 31 C Si Mn 0,12 0,5 0,7 Forta alungire Forta rupere Alungire Rezilienta 0C 450 MPa 550 MPa 26 % 50 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK Femax 38.48 SFA/AWS A5.1 - E7028 EN 499 - E 42 3 RB 53 H10 ISO 2560 - E 51 24B 150 36H C Si Mn 0,7 0,5 1,1 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta 0C Rezilienta -20C Rezilienta -30C Rezilienta -40C 460 MPa 545 MPa 27 % 240 J 120 J 100 J 80 J 35 J 3,2 x 350 4,0 x 450 5,0 x 450 5,6 x 450 OK Femax 38.65 SFA/AWS A5.1 - E7028 EN 499 - E 42 4 B 73 H5 ISO 2560 - E51 5B 170 36H C Si Mn 0,08 0,5 1,1 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -30C Rezilienta -40C Rezilienta -60C 430 MPa 540 MPa 26 % 110 J 95 J 65 J 50 J 3,2 x 340 4,0 x 450 5,0 x 450 6,0 x 450 OK Femax 38.85 SFA/AWS A5.1- E7028 ISO 2560 - E 51 4B 220 36H EN 499 - E 42 3 RB 73 H10 C Si Mn 0,10 0,6 1,1 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -30C 480 MPa 560 MPa 29 % 100 J 80 J 4,0 x 450 5,0 x 450 6,0 x 450 OK Femax 38.95 SFA/AWS A5.1 - E7028 EN 499 - E 38 4 B 73 H10 ISO 2560 - E 51 5B 240 46H0 C Si Mn 0,10 0,5 1,1 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C 400 MPa 500 MPa 30 % 110 J 90 J 4,0 x 450 5,0 x 450 5,6 x 450 6,0 x 450 OK SFA/AWS A5.1 - E7027 C 0,09 Forta alungire 450 MPa 3,2 x 450 Femax 39.50 EN 499 - E 42 2 RA 53 ISO 2560 - E 51 5 AR 160 35 Si Mn 0,3 0,8 Forta rupere Alungire Rezilienta +20C Rezilienta -20C 520 MPa 27 % 85 J 70 J 4,0 x 450 5,0 x 450 6,0 x 450
Electrozi pentru sudare MMA - oteluri slab aliate Tip electrod Standard de clasificare Compozitie Chimica % Caracteristici mecanice Dimensiune OK 48.08 Vac Pac SFA/AWS A5.5-E7018G EN 499-E46 5 1Ni B32 H5 C Si Mn Ni 0,06 0,35 1,2 0,9 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C Rezilienta -50C Rezilienta -60C 540 MPa 600 MPa 26 % 160 J 130 J 100 J 60 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 73.05 SFA/AWS A5.5 - E7018-G C Si Mn Cr Cu 0,04 0,5 0,6 0,6 0,3 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C 480 MPa 550 MPa 26 % 155 J 60 J 2,5 x 350 3,2 x 450 OK 73.08 Vac Pac SFA/AWS A5.5-E8018G EN 499-E46 5 ZB 32 C Si Mn Ni Cu 0,06 0,4 1,1 0,7 0,4 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C Rezilienta -50C 500 MPa 600 MPa 26 % 160 J 130 J 100 J 60 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 73.15 Vac Pac SFA/AWS A5.5-E8018G En 499-E46 5Mn 1Ni B42 H5 C Si Mn Ni 0,06 0,4 1,4 0,9 Forta alungire Forta rupere Alungire Rezilienta -50C 550 MPa 610 MPa 28 % 120 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 73.68 Vac Pac SFA/AWS A5.5-E8018 C1 En 499-E46 6 2Ni B32 H5 C Si Mn Ni 0,05 0,35 1,0 2,4 Forta alungire Forta rupere Alungire Rezilienta -55C Rezilienta -60C 520 MPa 610 MPa 26 % 110 J 105 J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 73.79 SFA/AWS A5.5 - E8016-C2 EN 499 - E 46 3 Ni B12 H5 C Si Mn 0,06 0,3 0,6 Forta alungire Forta rupere Alungire 520 MPa 610 MPa 26 % 2,5 x 350 3,2 x 450 Ni 3,3 Rezilienta -55C Rezilienta -60C Rezilienta -73C 170 J 160 J 90 J 4,0 x 450 5,0 x 450 OK 74.46 Vac Pac SFA/AWS A5.5-E7018A1 EN 1599-Emo B42 C Si Mn Mo 0,06 0,3 0,8 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -20C 460 MPa 560 MPa 27 % 175 J 100J 2,5 x 350 3,2 x 350 4,0 x 450 5,0 x 450 OK 74.70 Vac Pac SFA/AWS A5.5-E8018G EN 499 - E46 Mn Mo B32 C Si Mn Mo 0,08 0,4 1,5 0,4 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C Rezilienta -60C 540 MPa 630 MPa 26 % 110 J 80 J 50 J 3,2 x 350 4,0 x 450 OK 74.78 Vac Pac SFA/AWS A5.5-E9018-D1 EN 757-E55 Mn Mo B 120 20BH C Si Mn Mo 0,06 0,4 1,5 0,4 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta -40C Rezilienta -60C 540 MPa 630 MPa 26 % 110 J 80 J 50 J 3,2 x 350 4,0 x 450 OK 74.86 Tensitrode SFA/AWS A5.5 - E10018-D2 BS 2493 - 2Mn Mo BH C Si Mn Ni Mo 0,07 0,6 1,8 0,7 0,4 Forta alungire Forta rupere Alungire Rezilienta -51C 610 MPa 690 MPa 16 % 30 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 75.75 SFA/AWS A5.5 - E11018-G EN 757 - E 69 4 Mn2NiCrMoB 42 H5 C Si Mn Cr Ni Mo 0,06 0,3 1,7 0,4 2,2 0,4 Forta alungire Forta rupere Alungire Rezilienta -20C Rezilienta +20C Rezilienta -40C 755 MPa 820 MPa 20 % 115 J 85 J 70 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 76.16 Vac Pac SFA/AWS A5.5 - E8018-B2-H4R EN 1599 - E Cr Mo 1 B 42 H5 C Si Mn Cr Mo 0,07 0,4 0,6 1,4 0,6 Forta alungire Forta rupere Alungire Rezilienta -20C 550 MPa 620 MPa 22 % 70 J 2,5 x 350 3,2 x 350 4,0 x 350 OK 76.26 Vac Pac SFA/AWS A5.5-E9018-B3 EN 1599 - E CrMo2 B42 H5 C Si Mn Cr Mo 0,08 0,3 0,7 2,3 1,1 Forta alungire Forta rupere Alungire Rezilienta -20C 650 MPa 740 MPa 18 % 60 J 3,2 x 350 4,0 x 450 5,0 x 450 OK 76.35 SFA/AWS A5.5 - E8015-B6 EN 1599 - E CrMo5 B 42 H5 C Si Mn Cr Mo 0,08 0,4 0,8 5,0 0,6 Forta alungire Forta rupere Alungire Rezilienta +20C 460 MPa 550 MPa 19 % 47 J 2,5 x 300 3,2 x 350 4,0 x 450 5,0 x 450 OK 76.96 SFA/AWS A5.5 - E8015-B8 EN 1599 - E CrMo9 B 42 H5 C Si Mn Cr Mo 0,05 0,5 0,8 9,5 1,0 Forta alungire Forta rupere Alungire Rezilienta +20C 460 MPa 550 MPa 20 % 80 J 2,5 x 300 3,2 x 350 4,0 x 450 5,0 x 450 OK 76.98 Vac Pac SFA/AWS A5.5-E9015B9 EN 1599-E CR Mo91 B42 H5 C Si Mn Cr Ni Mo 0,1 0,4 0,7 9,0 0,7 1,0 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta 0C 650 MPa 760 MPa 18 % 70 J 50 J 2,5 x 350 3,2 x 350 4,0 x 450 OK 78.16 SFA/AWS A5.5 - E9018-G C Si Mn Cr Mo 0,1 0,4 0,8 1,0 0,2 Forta rupere Forta alungire Alungire Rezilienta +20C 870 MPa 900 MPa 18 % 50 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450
Electrozi inveliti pentru sudare MMA - oteluri inoxidabile si inalt aliate Tip electrod Standard de clasificare Compozitie Chimica % Caracteristici mecanice Dimensiune OK 61.20 SFA/AWS A5.4 - E308L-16 EN 1600 - E 19 9 L R 1 2 C Si Mn Cr Ni Mo Cu 0,03 0,7 0,9 19,5 10,0 0,5 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C 430 MPa 560 MPa 45 % 70 J 1,6 x 300 2,0 x 300 2,5 x 300 OK 61.25 SFA/AWS - E308H-15 EN 1600 - E 19 9 H B 2 2 C Si Mn Cr Ni Mo Cu 0,07 0,5 1,5 19,0 10,0 0,5 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C 300 MPa 570 MPa 45 % 96 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 61.30 Vac Pac SFA/AWS A5.4-E308L-17 EN 1600-E19 9 L R 12 C Si Mn Cr Ni 0,03 0,8 0,7 19,5 10,0 Forta alungire Forta rupere Alungire Rezilienta +20C 430 MPa 560 MPa 45 % 70 J 1,6 x 300 2,0 x 300 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 61.35 Vac Pac SFA/AWS A5.4-E308L-15 EN 1600-E19 9 L B 22 C Si Mn Cr Ni 0,03 0,4 1,7 19,5 10,5 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -120C Rezilienta -196C 460 MPa 580 MPa 45 % 100 J 70 J 45 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 61.41 Vac Pac SFA/AWS A5.4-E308L-17 EN 1600-E19 9 L R 5 3 C Si Mn Cr Ni 0,03 0,7 0,8 19.5 10,0 Forta alungire Forta rupere Alungire Rezilienta +20C 420 MPa 560 MPa 45 % 65 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 61.50 SFA/AWS A5.4 - E308H-17 EN 1600 - E 19 9 H R 1 2 C Si Mn Cr Ni Mo Cu 0,06 0,7 0,9 20,0 10,0 0,5 0,3 Forta alungire Forta rupere Alungire Rezilienta +20C 430 MPa 600 MPa 45 % 60 J 2,5 x 300 3,2 x 3050 4,0 x 350 OK 61.80 SFA/AWS A5.4 - E347-17 EN 1600 - E 19 9 Nb R 1 2 C Si Mn Cr Ni Mo Nb Cu 0,03 0,7 0,9 20,0 10,0 0,3 0,6 0,3 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -80C 480 MPa 620 MPa 40 % 60 J 40 J 2,0 x 300 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 61.81 Vac Pac SFA/AWS A5.4-92 E347-16 EN 1600-E19 9 Nb R 3 2 C Si Mn Cr Ni Nb 0,06 0,7 1,6 20,0 10,0 1,0 Forta alungire Forta rupere Alungire Rezilienta +20C 560 MPa 700 MPa 31 % 60 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 61.85 Vac Pac SFA/AWS A5.4 E347-15 EN 1600-E19 9 Nb B 2 2 C Si Mn Cr Ni Nb 0,05 0,5 1,7 19,5 10,0 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -60C 500 MPa 620 MPa 40 % 100 J 70 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 61.86 Vac Pac SFA/AWS A5.4 E347-15 EN 1600-E19 9 Nb R 1 2 C Si Mn Cr Ni Nb 0,03 0,7 0,8 19,0 10,0 0,3 Forta alungire Forta rupere Alungire Rezilienta +20C 520 MPa 660 MPa 35 % 55 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 62.53 Nu exista clasificare C Si Mn Cr Ni Mo Cu N 0,07 1,6 0,7 23,0 10,5 0,5 0,2 0,18 Forta alungire Forta rupere Alungire Rezilienta +20C 550 MPa 730 MPa 35 % 60 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 62.73 EN 1600 E 20 10 3 R 12 C Si Mn Cr Ni Mo Cu 0,08 1,0 1,3 19,8 9,5 3,3 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C 600 MPa 750 MPa 27 % 60 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 62.75 EN 1600 - E 20 10 3 B 1 2 C Si Mn Cr Ni Mo Cu 0,08 0,5 1,3 19,8 9,5 3,3 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C 610 MPa 750 MPa 27 % 65 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 63.20 Vac Pac SFA/AWS A5.4-E316L-16 EN 1600-E19 12 3 L R 1 1 C Si Mn Cr Ni Mo 0,03 0,7 0,8 18,5 12,0 2,8 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -60C Rezilienta -120C 480 MPa 580 MPa 35 % 65 J 45 J 32 J 1,6 x 300 2,0 x 300 2,5 x 300 3,2 x 350 OK 63.30 Vac Pac SFA/AWS A5.4-E316L-17 EN 1600-E19 12 3 L R 1 2 C Si Mn Cr Ni Mo 0,03 0,8 0,6 18,0 12,0 2,8 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -125C 460 MPa 570 MPa 40 % 60 J 32 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 63.32 SFA/AWS A5.4 - E 308Mo-26 En 1600 - E 20 10 3 R 7 3 C Si Mn Cr Ni Mo Cu 0,08 0,6 0,9 19,3 11,3 2,8 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C 560 MPa 710 MPa 34 % 65 J 3,2 x 450 4,0 x 450 OK 63.34 Vac Pac SFA/AWS A5.4-E316L-16 EN 1600-E19 12 3 L R 1 1 C Si Mn Cr Ni Mo 0,03 0,8 0,8 18,5 12,0 2,8 Forta alungire Forta rupere Alungire Rezilienta +20C 440 MPa 600 MPa 40 % 65 J 2,5 x 300 3,2 x 350 OK 63.35 SFA/AWS A5.4-E316L-15 EN 1600-E19 12 3 L B 2 2 C Si Mn Cr Ni Mo 0,03 0,5 1,7 18,5 12,6 2,8 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -120C Rezilienta -196C 460 MPa 600 MPa 35 % 95 J 60 J 35 J 2,5 x 300 3,2 x 350 4,0 x 450 5,0 x 350 OK 63.41 SFA/AWS A5.4 - E316L-26 EN 1600 - E 19 12 3 L R 5 3 C Si Mn Cr Ni Mo Cu 0,03 0,7 0,9 18,0 12,0 2,8 0,3 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -20C 460 MPa 580 MPa 35 % 60 J 50 J 2,0 x 300 2,5 x 300 3,2 x 350 4,0 x 450 5,0 x 450 OK 63.80 Vac Pac SFA/AWS A5.4-E318-17 EN 1600-E19 12 3 Nb R 3 2 C Si Mn Cr Ni Mo Nb 0,02 0,8 0,6 18,0 12,0 2,8 0,3 Forta alungire Forta rupere Alungire Rezilienta +20C 500 MPa 620 MPa 35 % 55 J 2,0 x 300 2,5 x 300 3,2 x 350 4,0 x 350 OK 63.85 SFA/AWS A5.4 - E318-15 EN 1600 - E 19 12 3 Nb B 4 2 C Si Mn Cr Ni Mo Nb Cu 0,06 0,5 1,7 18,5 12,0 2,8 1,1 0,5 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -120C 490 MPa 640 MPa 35 % 65 J 45 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 64.30 Vac Pac SFA/AWS A5.4-E317L-17 EN 1600-E19 13 4 L R 3 2 C Si Mn Cr Ni Mo 0,03 0,7 0,7 19,0 13,0 3,7 Forta alungire Forta rupere Alungire Rezilienta +20C 480 MPa 600 MPa 30 % 45 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 64.63 Vac Pac EN 1600-E 18 16 5 L R 3 2 C Si Mn Cr Ni Mo N 0,04 0,5 2,7 18,0 17,0 4,70,13 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -140C 450 MPa 640 MPa 35 % 80 J 45 J 3,2 x 350 4,0 x 350 OK 67.13 Vac Pac SFA/AWS A5.4-E310-16 EN 1600-E25 20 R 1 2 C Si Mn Cr Ni 0,1 0,5 1,9 26 21 Forta alungire Forta rupere Alungire Rezilienta +20C 560 MPa 600 MPa 35 % 60 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 67.15 Vac Pac SFA/AWS A5.4-E310-16 EN 1600-E25 20 B 2 2 C Si Mn Cr Ni 0,1 0,3 2,0 26,0 20,0 Forta alungire Forta rupere Alungire Rezilienta +20C 410 MPa 590 MPa 35 % 100 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 67.20 Vac Pac SFA/AWS A5.4-E309MoL 16 EN 1600-E23 12 2 L R 1 1 C Si Mn Cr Ni Mo 0,03 0,8 0,8 23,0 13,0 2,9 Forta alungire Forta rupere Alungire Rezilienta +20C 480 MPa 640 MPa 35 % 60 J 2,0 x 300 2,5 x 300 3,2 x 350 OK 67.43 Vac Pac SFA/AWS A5.4 E307-15 EN 1600-E 18 8 Mn B 1 2 C Si Mn Cr Ni 0,08 0,7 5,5 18,5 9 Forta alungire Forta rupere Alungire Rezilienta +20C 440 MPa 630 MPa 35 % 80 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 67.45 Vac Pac SFA/AWS A5.4 E307-15 En 1600-E 18 8 Mn B 1 2 C Si Mn Cr Ni 0,1 0,5 6,3 18,8 9 Forta alungire Forta rupere Alungire Rezilienta +20C 470 MPa 605 MPa 35 % 70 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 67.50 Vac Pac SFA/AWS A5.4 E2209-17 EN 1600-E 22 9 3 N L R 3 2 C Si Mn Cr Ni Mo N 0,03 0,8 1,0 23,0 9,0 3,0 0,15 Forta alungire Forta rupere Alungire Rezilienta +20C 660 MPa 820 MPa 25 % 70 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 67.51 SFA/AWS A5.4 - E2209-26 EN 1600 - E 22 9 3 N L R 53 C Si Mn Cr Ni Mo Cu N 0,03 0,7 0,9 22,5 9,5 3,0 0,2 0,16 Forta alungire Forta rupere Alungire Rezilienta +20C 645 MPa 800 MPa 25 % 50 J 2,5 x 300 3,2 x 250 4,0 x 350 OK 67.52 Vac Pac SFA/AWS A5.4 E307-25 EN 1600-E 18 8 Mn B 8 3 C Si Mn Cr Ni 0,1 1,0 7,0 18,0 9,0 Forta alungire Forta rupere Alungire Rezilienta +20C 420 MPa 630 MPa 45 % 70 J 2,5 x 350 3,2 x 450 4,0 x 350 5,0 x 450 OK 67.53 Vac Pac SFA/AWS A52 9 3 N L R 1 2 C Si Mn Cr Ni Mo N 0,03 1,0 0,7 23,5 9,0 3,0 0,15 Forta alungire Forta rupere Alungire Rezilienta +20C 660 MPa 840 MPa 25 % 70 J 3,2 x 350 OK 67.55 Vac Pac SFA/AWS A.5 E2209-16 EN 1600-E 22 9 3 N L B 2 2 C Si Mn Cr Ni Mo N 0,03 0,7 1,0 23,0 9,0 3,0 0,15 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -40C Rezilienta -60C 650 MPa 800 MPa 28 % 100 J 75 J 65 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 67.60 Vac Pac SFA/AWS A5.4-E309L-17 C Si Mn Cr Ni 0,03 0,8 0,9 24,0 12,5 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -10C 470 MPa 580 MPa 32 % 50 J 40 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 67.62 Vac Pac SFA/AWS A5.4-E309-26 EN 1600-E23 12 R 7 3 C Si Mn Cr Ni 0,05 0,8 0,6 24,0 12,5 Forta alungire Forta rupere Alungire Rezilienta +20C 450 MPa 570 MPa 40 % 60 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 67.66 SFA/AWS A5.4 - E309L-16 C Si Mn Cr Ni Mo Cu 0,03 0,5 0,1 23,0 13,0 0,5 0,2 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -20C 430 MPa 580 MPa 45 % 70 J 4,0 x 350 OK 67.70 Vac Pac SFA/AWS A5.4-E309MoL17 EN 1600-E23 12 L R 3 2 C Si Mn Cr Ni Mo 0,03 0,8 0,6 23,0 13,0 2,7 Forta alungire Forta rupere Alungire Rezilienta +20C 510 MPa 620 MPa 33 % 50 J 2,5 x 300 3,2 x 250 4,0 x 350 5,0 x 350 OK 67.71 Vac Pac SFA/AWS A5.4-E309MoL17 EN 1600-E22 12 3 L R 5 3 C Si Mn Cr Ni Mo 0,03 0,9 0,9 23,0 13,0 2,6 Forta alungire Forta rupere Alungire Rezilienta +20C 500 MPa 620 MPa 35 % 55 J 3,2 x 250 4,0 x 350 5,0 x 350 OK 67.75 Vac Pac SFA/AWS A5.4-E309L-15 EN 1600-E23 12 L B 42 C Si Mn Cr Ni Mo 0,03 0,3 0,2 24,0 13,0 0,3 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -80C 460 MPa 570 MPa 35 % 75 J 55 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 68.15 Vac Pac SFA/AWS A5.4-E410-15 EN 160- E13 B 4 2 C Si Mn Cr 0,06 0,5 0,5 13,0 Forta alungire Forta rupere Alungire Rezilienta +20C 390 MPa 520 MPa 25 % 55 J 2,5 x 350 3,2 x 450 4,0 x 450 5,0 x 450 OK 68.17 Vac Pac SFA/AWS A5.4-E410NiMo-16 EN 1600-E13 4 R 3 2 C Si Mn Cr Ni Mo 0,03 0,4 0,6 12,0 4,6 0,6 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -10C Rezilienta -40C 650 MPa 870 MPa 17 % 45 J 45 J 40 J 2,5 x 350 3,2 x 350 4,0 x 350 OK 68.25 Vac Pac SFA/AWS A5.4-E410NiMo-15 EN 1600-E13 4 B 4 2 C Si Mn Cr Ni Mo 0,03 0,4 0,6 12,5 4,5 0,6 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -20C 680 MPa 880 MPa 17 % 60 J 53 J 3,2 x 350 4,0 x 350 5,0 x 350 OK 68.37 NF A 81-343 - E Z 17.4.1 B 20 C Si Mn Cr Ni Mo 0,06 0,3 1,2 16,0 5,5 0,5 Forta alungire Forta rupere Alungire 710 MPa 950 MPa 14 % 2,5 x 350 3,2 x 450 4,0 x 450 OK 68.53 Vac Pac EN 1600-E 25 9 4 N L R 3 2 C Si Mn 0,03 0,6 0,7 Forta alungire Forta rupere Alungire 700 MPa 850 MPa 30% 2,5 x 300 3,2 x 350 Cr Ni Mo N 25,5 10,0 4,0 0,25 Rezilienta +20C Rezilienta -40C 50 J 35 J 4,0 x 350 OK 68.55 Vac Pac EN 1600-E 25 9 4 N L B 4 2 C Si Mn Cr Ni Mo N 0,03 0,6 0,9 25,5 10,0 4,0 0,25 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -40C Rezilienta -60C 700 MPa 900 MPa 28 % 90 J 55 J 45 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 68.81 Vac Pac SFA/AWS A5.4-E312-17 EN 1600-E29 9 R 3 2 C Si Mn Cr Ni 0,12 0,7 0,8 29,0 10,0 Forta alungire Forta rupere Alungire Rezilienta +20C 580 MPa 750 Mpa 25 % 30 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 68.82 Vac Pac SFA/AWS A5.4-E312-17 EN 1600-E29 9 R 1 2 C Si Mn Cr Ni 0,12 1,0 1,0 29,0 10,0 Forta alungire Forta rupere Alungire Rezilienta +20C 500 MPa 750 MPa 25 % 40 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 69.25 Vac Pac EN 1600-E 20 16 3MnLB 4 2 C Si Mn Cr Ni Mo N 0,03 0,5 6,5 19,0 16,0 3,0 0,15 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -196C 450 MPa 650 MPa 30 % 90 J 50 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 69.33 Vac Pac SFA/AWS A5.4-E385-16 E 20 25 5 Cu N L R 3 2 C Si Mn Cr Ni Mo Cu 0,03 0,5 1,0 20,5 25,0 5,0 1,5 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -140C 400 MPa 575 MPa 35 % 80 J 45 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 69.63 EN 1600 - E 20 25 5 Cu N L 3 2 C Si Mn Cr Ni Mo Cu N 0,04 0,6 2,8 20,0 25,0 6,5 1,2 0,16 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -140C 460 MPa 680 MPa 40 % 80 J 50 J 2,5 x 300 3,2 x 350 4,0 x 350
Electrozi inveliti pentru sudare MMA - aliaje pe baza de aluminiu Tip electrod Standard de clasificare Compozitie Chimica % Caracteristici mecanice Dimensiune OK 96.10 Vac Pac SFA/AWS A5.3-E1100 DIN 1732-EL-Al99,5 Al Si Fe 99,5 0,30 0,4
2,5 x 350 3,2 x 350 4,0 x 350 OK 96.20 Vac Pac DIN 1732-EL-AlMn1 Al Mn Si Fe 97,5 1,3 0,5 0,7
2,5 x 350 3,2 x 350 4,0 x 350 OK 96.40 Vac Pac DIN 1732-EL-AlSi5 Al Si Fe 94 5,0 0,4
2,5 x 350 3,2 x 350 4,0 x 350 OK 96.50 Vac Pac DIN 1732-EL-AlSi12 Al Si Fe 87,5 12,0 0,5
2,5 x 350 3,2 x 350 4,0 x 350
Electrozi inveliti pentru sudare MMA - aliaje pe baza de nichel Tip electrod Standard de clasificare Compozitie Chimica % Caracteristici mecanice Dimensiune OK 92.05 Vac Pac AFA/AWS A5.11-ENi-1 DIN 1736-EL-NiTi3 C Si Mn Fe Ti Ni 0,05 1,0 0,7 0,7 3,0 92,0 Forta alungire Forta rupere Alungire 320 MPa 450 MPa 25 % 2,5 x 300 3,2 x 350 4,0 x 350 OK 92.15 SFA/AWS A5.11-ENiCrFe-2 DIN 1736-EL-NiCr15FeNb C Si Mn Cr Ni Mo Nb Fe 0,1 0,5 2,0 15,5 70,0 2,0 2,0 8,0 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -196C 420 MPa 660 MPa 45 % 110 J 90J 2,5 x 300 3,2 x 350 4,0 x 350 OK 92.15 SFA/AWS A5.11-ENiCrFe-3 C 0,1 Forta alungire 410 MPa 2,5 x 300 Vac Pac DIN 1736-EL-NiCr15FeMn Si Mn Cr Ni Nb Fe 0,6 6,0 16,0 70,0 2,0 6,0 Forta rupere Alungire Rezilienta +20C Rezilienta -196C 640 MPa 40 % 100 J 80 J 3,2 x 350 4,0 x 350 5,0 x 350 OK 92.26 SFA/AWS A5.11 - ENiCRFe-3 EN ISO 14172 - E Ni 6182 C Si Mn Cr Ni Nb Cu Ti Ta Fe 0,03 0,5 6,6 15,8 67 1,1 0,5 0,5 0,3 8,8 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -196C 410 MPa 640 MPa 40 % 100 J 80 J 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 92.35 Vac Pac SFA/AWS A5.11-90-ENiCrMo-5 DIN 8555-E23-E250 CKT C Si Mn Mo Cr W Fe Ni 0,06 0,7 0,7 16,5 15,5 3,8 5,5 57,0 Forta alungire Forta rupere Alungire 515 MPa 750 MPa 17 % 2,5 x 300 3,2 x 350 4,0 x 350 5,0 x 350 OK 92.45 Vac Pac SFA/AWS A5.11-ENiCrMo-3 DIN 1736-EL-NiCr20Mo9Nb C Si Mn Cr Ni Mo Nb Fe 0,03 0,4 0,4 22,0 64,0 9,5 3,3 3,0 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -196C 480 MPa 800 MPa 40 % 70 J 50 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 92.55 SFA/AWS A5.11-ENiCrMo6 C Si Mn Cr Ni Mo Nb W Fe 0,08 0,7 3,0 13,0 70,0 6,5 1,3 1,5 4,0 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -60C Rezilienta -196C 460 MPa 705 MPa 40 % 95 J 90 J 80 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 92.59 DIN 1726-EL-NiCr22Mo16 C Si Mn Cr Ni Mo 0,02 0,1 0,15 15,0 Bal 23,0 Forta alungire Forta rupere Alungire Rezilienta -60C Rezilienta -196C 430 MPa 770 MPa 40 % 70 J 60 J 2,5 x 300 3,2 x 350 4,0 x 350 OK 92.82 EN ISO 14172 - E Ni 6082 C Si Mn Cr Ni 0,03 0,4 4,8 19,4 67 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -196C 390 MPa 620 MPa 35 % 80 J 65 J 2,5 x 300 3,2 x 300 4,0 x 350 Mo Nb Cu Ti Fe 1,0 2,3 0,5 0,5 2,3 OK 92.86 SFA/AWS A5.11 - E NiCu-7 EN ISO 14172 - E Ni 4060 C Si Mn Ni Nb Cu Al Ti Fe 0,01 0,3 2,1 66 0,3 29 0,5 0,2 1,6 Forta alungire Forta rupere Alungire Rezilienta +20C Rezilienta -196C 410 MPa 640 MPa 40 % 100 J 80 J 2,5 x 300 3,2 x 350 4,0 x 350
OK 43.32 Type Rutile
Easy-to-weld rutile type electrode for welding in the flat position. The good flowing properties of the weld metal give a good finish to the weld beads on both butt and fillet welds. Good slag detachability. The stable arc, even at low welding currents, makes the electrode very suitable for sheet metal welding. Welding current AC, DC+/-, OCV 50 V Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.1 E6013 EN ISO 2560-A E 42 0 RR 12
ABS 2 BV 1 DB 80.039.02 DNV 2 GL 1 LR 1 VdTV 00621 CE EN13479 RS 2
C 0,12 Si 0,55 Mn 0,5 P 0,03 S 0,03
Yield stress, MPa 460 Tensile strength, MPa 550 Elongation, % 26 Elongation, % 26 Charpy V Test temps, C Impact values, J +20 65 0 >47
Redrying temperature, C 80 Recovery 95%
Diameter, mm 1,6 2,0 2,5 3,2 3,2 4,0 4,0 5,0 6,0 Length, mm 300 300 350 350 450 350 450 450 450 Arc voltage, V 27 23 25 26 26 25 27 26 30,6 Welding current, A 30-60 40-80 50-110 80-150 80-140 120-210 120-210 170-290 230-370 N. Kg weld metal/kg 0,50 0,54 0,54 0,57 0,54 0,25 0,54 0,56 0,52 electrodes B. No. of electrodes/kg weld metal 263 167 88 50 41 35 27 17 12,4 H. Kg weld metal/hour arc time 0,4 0,6 0,9 1,3 1,3 1,6 1,9 2,5 2,8 T. Burn-off time, s/electrode 34 36 46 57 74 63 76 87 105
OK 46.00
SMAW Type Rutile
OK 46.00 is the best, all-round, rutile electrode and it is relatively insensitive to rust or other surface impurities. It deposits smooth weld beads in all positions, including vertical down, and the slag is easy to remove. OK 46.00 is very easy to strike and restrike, making it ideal for short welds, root runs and tacking. Welding current AC, DC+/-, OCV 50 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN ISO 2560-A E 38 0 RC 11 SFA/AWS A5.1 E6013
ABS 2 BV 2 DB 10.039.05 DNV 2 GL 2 LR 2 VdTV 00623 CE EN 13479 Class NK KMW2 BKI 2 GOST-R NAKS/HAKC
C 0,08 Si 0,3 Mn 0,4 P 0,03 S 0,03
Yield stress, MPa 400 Tensile strength, MPa 510 Elongation, % 28 Elongation, % 28 Charpy V Test temps, C Impact values, J 0 70 -20 35
Redrying temperature, C 70-80 Redrying time, hours 1 Recovery 95%
Diameter, mm 1,6 2,0 2,5 3,2 4,0 5,0 Length, mm 300 300 350 350 350 350 Arc voltage, V 26 25 22 22 22 24 Welding current, A 30-60 50-70 60-100 80-150 100-200 150-290 N. Kg weld metal/kg electrodes 0,63 0,60 0,65 0,65 0,60 0,60 B. No. of electrodes/kg weld metal 263 172 86 53 39 24 H. Kg weld metal/hour arc time 0,38 0,55 0,80 1,30 1,60 2,30 T. Burn-off time, s/electrode 36 38 50 57 65 87
OK 48.00
SMAW Type Lime-basic
A reliable, general purpose, LMA electrode for mild and low-alloy steels. OK 48.00 deposits a tough, crack-resistant weld metal. High welding speed in the vertical-up position. OK 48.00 is insensitive to the composition of the base material within fairly wide limits. The electrode can be used for welding structures where difficult stress conditions cannot be avoided. Welding current DC+/(-)
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.1 E7018 EN ISO 2560-A E 42 4 B 42 H5
ABS 3H5, 3YH5 DB 10.039.12 DNV 3 YH5 GL 3Y H5 LR 3, 3Y H5 VdTV 00690 CE EN 13479
C 0,06 Si 0,5 Mn 1,2 P 0,02 S 0,015
Yield stress, MPa 445 Tensile strength, MPa 540 Elongation, % 29 Elongation, % 29 Charpy V Test temps, C Impact values, J -20 140 -40 70
Redrying temperature, C 350 Redrying time, hours 2 Recovery 125%
Diameter, mm 1,6 2,0 2,5 3,2 3,2 4,0 4,0 5,0 5,0 6,0 7,0 Length, mm 300 300 350 350 450 350 450 350 450 450 450 Arc voltage, V 24 22 23 22 23 24 26 23 23 23 25 Welding current, A 30-55 50-80 80- 110 90- 140 90- 140 125- 210 125- 210 200- 260 200- 260 220- 340 280- 410 N. Kg weld metal/kg electrodes 0,59 0,63 0,65 0,64 0,64 0,51 0,67 0,53 0,69 0,72 0,72 B. No. of 192 119 62,5 43 32,3 35,0 20,5 23,0 13,5 9,6 7,0 electrodes/kg weld metal H. Kg weld metal/hour arc time 0,38 0,6 1,0 1,3 1,5 2,1 2,1 2,6 2,6 3,7 4,4 T. Burn-off time, s/electrode 50 50 56 66 76 64 86 78 102 102 117
OK 48.68
SMAW Type Lime-basic
General purpose basic AC, DC +(-) electrode for mild and low alloyed steels. Very good impact values and extremely low moisture pick-up. Welding properties are very good in all positions except vertically down. The 2.0 to 3.25 mm electrodes are especially designed for welding root passes. The electrode welds with a soft and stable arc. It is very easy to have full control of the arc even in the 4G position. Dry electrodes or electrodes protected by VacPac have a hydrogen content below 3 ml/100 g deposited weld metal according to AWS. Welding current AC, DC+(-) OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.1 E7018-1 EN ISO 2560-A E 42 5 B 42 H5
ABS 3H5, 3Y BV 3Y H5 DNV 3 YH5 LR 3, 3Y H5 CE EN13479
C 0,06 Si 0,5 Mn 1,3 P 0,02 S 0,02
Yield stress, MPa 470 Tensile strength, MPa 560 Elongation, % 28 Elongation, % 28 Charpy V Test temps, C Impact values, J -20 160 -40 130 -50 100
Redrying temperature, C 350 Redrying time, hours 2 Recovery 120%
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 350 450 450 450 Arc voltage, V 22 22 22 23 Welding current, A 75-110 105-150 150-200 180-260 N. Kg weld metal/kg electrodes 0,70 0,66 0,65 0,68 B. No. of electrodes/kg weld metal 60,2 35,0 22,7 14,6 H. Kg weld metal/hour arc time 1,0 1,2 1,9 2,7 T. Burn-off time, s/electrode 58 81 88 90
OK 53.68
SMAW Type Lime-basic
OK 53.68 is an extra-high quality LMA electrode, particularly suitable for on-site welding. OK 53.68 yields a homogeneous, high- quality weld metal with an extra low content of impurities. The electrode operates well on AC as well as DC positive and negative. DC negative is preferred, as it produces a small, easily controlled weld pool, minimising the risk of burn-through or undercutting. OK 53.68 is CTOD tested. Welding current AC, DC +(-) OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.1 E7016-1 EN ISO 2560-A E 42 5 B 12 H5
ABS 3H5, 3Y BV 3YH5 DNV 4 YH5 VdTV 06807 CE EN 13479
C 0,06 Si 0,4 Mn 1,3 P 0,025 S 0,015 Cr 0,05 Ni 0,07 Mo 0,02 V 0,01 Nb 0,01 Cu 0,07 Al 0,01 Sn 0,01 Ti 0,04 Pb 0,01 As 0,05
Yield stress, MPa >420 Tensile strength, MPa 510-640 Elongation, % 22 Elongation, % 22 Charpy V Test temps, C Impact values, J -20 >150 -40 >80 -50 >47
Redrying temperature, C 350 Redrying time, hours 2 Recovery 100%
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 350 450 450 450 Arc voltage, V 22 22 22 22 Welding current, A 55-85 80-130 110-170 180-230 N. Kg weld metal/kg electrodes 0,58 0,61 0,65 0,66 B. No. of electrodes/kg weld metal 90 41 26 17 H. Kg weld metal/hour arc time 0,8 1,2 1,7 2,4 T. Burn-off time, s/electrode 50 73 83 90 OK 53.70
SMAW Type Lime-basic
A low-hydrogen AC/DC electrode for the one-sided welding of pipes and general structures. The root penetration is good, leaving a flat bead with easily removable slag. The stable arc and the well-balanced slag system make the electrode easy to weld in all positions. Suitable for welding transmission pipelines made from pipe steels up to API 5LX56. It is also suitable for welding the root in higher strength pipes, API 5LX60, 5LX65, 5LX70. Welding current AC, DC+(-) OCV 60 V Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.1 E7016-1 DIN 1913 E 51 55 B10 EN 499 E 42 5 B 12 H5 GOST 9467-75 E50A ISO 2560 E 51 5 B 24 H
ABS 3H5, 3Y H5 CE EN 13479 DNV 3 YH5 LR 3YH15 Sepros UNA 485155 vniist
C 0,06 Si 0,5 Mn 1,2 P 0,015 S 0,015
Yield stress, MPa 440 Tensile strength, MPa 530 Elongation, % 30 Elongation, % 30 Charpy V Test temps, C Impact values, J -20 150 -40 120 -50 100
Redrying temperature, C 350 Redrying time, hours 2 Recovery 100%
Diameter, mm 2,5 3,2 3,2 4,0 Length, mm - 350 350 450 400 Arc voltage, V - 26 24 24 24 Welding current, A - 60-85 80-130 80-130 115-190 N. Kg weld metal/kg electrodes - 0,63 0,59 0,59 0,63 B. No. of electrodes/kg weld metal - 87,7 54,5 42 25 H. Kg weld metal/hour arc time - 0,7 1,1 1,1 1,7 T. Burn-off time, s/electrode - 57 61 78 86
OK 55.00
SMAW Type Lime-basic
OK 55.00 is a reliable, high-quality, LMA electrode, particularly suitable for welding high strength low-alloy steels. The good, low- temperature impact strength of the weld metal should be noted. The weld metal is also very resistant to hot cracking. The electrode is also suitable for welding high strength ship's steel, grades A, D and E. Welding current AC, DC+ OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.1 E7018-1H4 R CSA W48 E4918-1 EN ISO 2560-A E 46 5 B 32 H5
ABS 3H5, 3Y BV 3Y HHH DB 10.039.03 DNV 4YH5 GL 3YH5 LR 3Y H5 RS 3YHH VdTV 00632 CE EN 13479
C 0,07 Si 0,5 Mn 1,4 P 0,03 S 0,03 Cr 0,1 Ni 0,1 Mo 0,1 V 0,03 Nb 0,02 Cu 0,1 Al 0,03 Sn 0,01 Ti 0,03 Pb 0,02 As 0,03
Yield stress, MPa 480 Tensile strength, MPa 590 Elongation, % 28 Elongation, % 28 Charpy V Test temps, C Impact values, J -20 115 -50 50
Redrying temperature, C 350 Redrying time, hours 2 Recovery 125%
Diameter, mm 2,5 3,2 3,2 4,0 4,0 5,0 6,0 Length, mm 350 350 450 350 450 450 450 Arc voltage, V 23 23 24 23 24 24 25 Welding current, A 80-110 110-140 110-140 140-200 140-200 200-270 215-360 N. Kg weld metal/kg electrodes 0,64 0,62 0,69 0,62 0,70 0,72 0,72 B. No. of electrodes/kg weld metal 65,8 41,1 30,0 28,0 19,0 13,0 9,0 H. Kg weld metal/hour arc time 0,86 1,22 1,4 1,77 2,0 3,0 4,0 T. Burn-off time, s/electrode 64 72 88 73 94 94 98
OTELURI SLAB ALIATE
OK 48.08 SMAW Type Lime-basic
OK 48.08 is an LMA electrode with very good mechanical properties suitable for demanding applications, such as offshore. The weld metal contains approximately 1% Ni for high impact values down to -40C. The coating is of the latest LMA type for optimum resistance to porosity and hydrogen cracking. OK 48.08 is CTOD tested. Welding current AC, DC+(-) OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.1 E7018 EN ISO 2560-A E 42 4 B 32 H5
ABS 3H5 3Y DB 10.039.31 DNV 4 Y40H5 GL 4YH5 LR 4Y40 H15 Sepros UNA 409819 VdTV 05778 CE EN 13479
C 0,06 Si 0,4 Mn 1,2 Ni 0,8 P 0,02 S 0,015 Cr 0,1 Mo 0,06 V 0,03 Nb 0,02 Cu 0,1 Al 0,03 Sn 0,01 Ti 0,03 Pb 0,02 As 0,03
Yield stress, MPa 480 Tensile strength, MPa 560 Elongation, % 30 Elongation, % 30 Charpy V Test temps, C Impact values, J -20 160 -40 130 -50 100 -60 60
Redrying temperature, C 350 Redrying time, hours 2 Recovery 125%
Diameter, mm 2,0 2,5 3,2 3,2 4,0 4,0 5,0 6,0 Length, mm 300 350 350 450 350 450 450 450 Arc voltage, V 22 27 22 22 22 22 23 26 Welding current, A 55-80 75-110 110-150 110-150 150-200 150-200 190-275 220-360 N. Kg weld metal/kg electrodes 0,57 0,57 0,62 0,66 0,66 0,69 0,69 0,66 B. No. of electrodes/kg weld metal 135,1 88,2 42,3 30,0 26,5 20,3 14,0 10,0 H. Kg weld metal/hour arc time 0,6 1,0 1,3 1,4 2,0 2,0 3,0 3,8 T. Burn-off time, s/electrode 42 41 66 85 68 90 85 95
OK 73.08 SMAW Type Lime-basic
OK 73.08 is a NiCu-alloyed LMA electrode, which deposits a weld metal with good corrosion resistance to sea-water and flue gases, for the welding of weatherproof steel and for ships hull structural steel. The weld metal has excellent mechanical properties. It is particularly suitable for welding the shell plating of ice-breakers and other ships, which work under conditions where the protective paint coating wears off. Welding current AC, DC(+) OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E8018-G EN ISO 2560-A E 46 5 Z B 32
ABS 3Y H5 BV 3Y HH DB 10.039.20 DNV 3 YH10 GL 3YH15 LR 3, 3Y H15 RS 3YHH VdTV 02115 CE EN 13479
C 0,06 Si 0,4 Mn 1,0 Ni 0,7 Cu 0,4 P 0,02 S 0,02
Yield stress, MPa 500 Tensile strength, MPa 590 Elongation, % 27 Elongation, % 27 Charpy V Test temps, C Impact values, J -20 160 -40 130 -50 70
Redrying temperature, C 350 Redrying time, hours 2 Recovery 125%
Diameter, mm 2,0 2,5 3,2 3,2 4,0 5,0 6,0 Length, mm 300 350 350 450 450 450 450 Arc voltage, V 20 21 23 22 23 27 28 Welding current, A 60-90 80-115 100-150 100-150 130-200 190-280 240-370 N. Kg weld metal/kg electrodes 0,62 0,62 0,62 0,66 0,68 0,70 0,68 B. No. of electrodes/kg weld metal 113,0 66,0 43 30,5 20,0 13,5 9,5 H. Kg weld metal/hour arc time 0,7 0,9 1,2 1,3 1,8 2,6 3,3 T. Burn-off time, s/electrode 42 59 68 90 100 106 115
OK 73.46 SMAW Type Lime-Basic
Low-alloyed, MMA electrode for welding fine-grained steels. The weld metal has excellent impact properties down to -40C. Welding current DC(+)
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E8018-G EN 757 E 55 4 1.5NiMo B
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 350 450 450 450 Welding current, A 75-100 100-150 140-190 190-270 B. No. of electrodes/kg weld metal 68 32 22 14 T. Burn-off time, s/electrode 59 75 98 106
OK 73.68 SMAW Type Lime-basic
OK 73.68 is a 2.5% nickel-alloyed LMA electrode suitable for the welding of low-alloy steels with impact requirements down to -60C. The composition of the weld metal is such that good, low-temperature impact properties are obtained, even when welding vertically up. The weld metal of OK 73.68 is also noted for its good corrosion resistance to sea-water and sulphuric acid fumes. Welding current AC, DC+ OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E8018-C1 EN ISO 2560-A E 46 6 2Ni B 32 H5
ABS 3H5, 3Y400 BV 5Y40M H5 DNV 5 YH10 GL 6Y55H10 LR 5Y40H5 PRS 4YH10 RS 3YHH Sepros UNA 409819 VdTV 01529 CE EN 13479
C 0,05 Si 0,3 Mn 1,0 Ni 2,4 P 0,02 S 0,02 Cr 0,1 Mo 0,05 V 0,03 Nb 0,02 Cu 0,1 Al 0,03 Sn 0,01 Ti 0,03 Pb 0,02 As 0,03
Yield stress, MPa 520 Tensile strength, MPa 610 Elongation, % 26 Elongation, % 26 Charpy V Test temps, C Impact values, J -55 110 -59 105 -60 105
Redrying temperature, C 350 Redrying time, hours 2 Recovery 120%
Diameter, mm 2,0 2,5 3,2 4,0 5,0 Length, mm 300 350 450 450 450 Arc voltage, V 21 23 23 23 27 Welding current, A 55-75 70-110 105-150 140-190 190-270 N. Kg weld metal/kg electrodes 0,62 0,62 0,62 0,65 0,65 B. No. of electrodes/kg weld metal 130,0 70,0 32,0 21,0 13,5 H. Kg weld metal/hour arc time 0,6 0,9 1,4 2,0 2,5 T. Burn-off time, s/electrode 46 55 81 88 104
OK 73.79 SMAW Type Lime-basic
OK 73.79 is a nickel-alloyed, LMA electrode for welding 3.5 Ni steel with impact requirements down to -101C. It is used, for example, for ethane tanks and chemical plants. Welding current AC, DC (+-) OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E8016-C2 EN 499 E 46 6 3Ni B12 H5
Redrying temperature, C 350 Redrying time, hours 2 Recovery 100%
Diameter, mm 2,5 3,2 3,2 4,0 5,0 Length, mm 350 350 450 450 450 Arc voltage, V 25 25 25 27 29 Welding current, A 70-110 80-150 80-150 90-190 110-240 N. Kg weld metal/kg electrodes 0,60 0,60 0.60 0,63 0,60 B. No. of electrodes/kg weld metal 76 39 37 26 15 H. Kg weld metal/hour arc time 0,8 1,4 1,5 1,8 2,1 T. Burn-off time, s/electrode 60 71 77 88 100
OK 74.46 SMAW Type Lime-basic
OK 74.46 is an LMA electrode alloyed with 0.5% Mo for welding steels for pressure vessels. The running characteristics make it suitable for welding joints in inclined positions. The composition of the coating is adapted for welding with low currents, making OK 74.46 very suitable for the welding of pipes. Welding current DC+, AC OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E7018-A1 EN 1599 VdTV 01043 CE EN 13479
C 0,06 Si 0,5 Mn 0,7 Mo 0,5 Yield stress, MPa 460 Tensile strength, MPa 560 Elongation, % 27
E Mo B 32 H5
P 0,02 S 0,02
Elongation, % 27 Charpy V Test temps, C Impact values, J +20 175 0 >31
Redrying temperature, C 350 Redrying time, hours 2 Recovery 115%
Diameter, mm 2,0 2,5 3,2 3,2 4,0 5,0 6,0 Length, mm 300 350 350 450 450 450 450 Arc voltage, V 22 23 23 25 26 27 28 Welding current, A 55-80 75-110 105-150 105-150 140-200 190-270 260-370 N. Kg weld metal/kg electrodes 0,59 0,59 0,54 0,59 0,65 0,65 0,65 B. No. of electrodes/kg weld metal 136,0 73,0 53,0 37,0 22,5 14,5 10.0 H. Kg weld metal/hour arc time 0,7 0,9 1,0 1,2 1,8 2,4 3,4 T. Burn-off time, s/electrode 40 55 66 81 90 104 108
OK 74.70 SMAW Type Lime-basic
OK 74.70 is an LMA electrode used for welding high strength, low-alloyed steel. The electrode is designed for various applications, including pipelines. Welding current DC+(-)
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E8018-G EN 499 E 50 4 MnMo B 42 H5 EN ISO 2560-A E 50 4 Z B 42 H5
Sepros UNA 485155 VNIIST
C 0,08 Si 0,375 Mn 1,425 Mo 0,425 P 0,015 S 0,015
Yield stress, MPa 540 Tensile strength, MPa 630 Elongation, % 26 Elongation, % 26 Charpy V Test temps, C Impact values, J
-20 110 -40 80 -60 50
Redrying temperature, C 350 Redrying time, hours 2 Recovery 115%
Diameter, mm 3,2 4,0 4,0 5,0 Length, mm 350 350 450 450 Arc voltage, V 23 23 24 23 Welding current, A 80-140 90-190 90-190 150-250 N. Kg weld metal/kg electrodes 0,58 0,61 0,63 0,65 B. No. of electrodes/kg weld metal 50,0 31,6 23,4 15,0 H. Kg weld metal/hour arc time 1,14 1,60 1,66 2,30 T. Burn-off time, s/electrode 63 71 93 102
OK 74.78 SMAW Type Lime basic
OK 74.78 is an LMA electrode suitable for welding high tensile steels used in low-temperature applications. Good notch toughness down to -40C. Very suitable for both the enclosed welding and cladding of rails, when a hardness of about 250 HV is required. The moisture content of the coating is very low, which makes OK 74.78 suitable when preheating cannot be applied. Welding current AC, DC+ OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E9018-D1 EN 757 E 55 4 MnMo B 3 2 H5
ABS 3H5, 3Y BV 3Y HH DB 10.039.17 DB 20.039.02 DNV 3 YH10 LR 3, 3Y H15 Sepros UNA 409819 VdTV 01027 CE EN 13479
C 0,06 Si 0,4 Mn 1,5 Mo 0,4 P 0,02 S 0,02 Cr 0,1 Ni 0,1 V 0,03 Nb 0,02 Cu 0,1 Al 0,03 Sn 0,01 Ti 0,03 Pb 0,02 Yield stress, MPa 600 Tensile strength, MPa 650 Elongation, % 24 Elongation, % 24 Charpy V Test temps, C Impact values, J 0 100 -20 90 -51 60 -30 28
As 0,03
Redrying temperature, C 350 Redrying time, hours 2 Recovery 125%
Diameter, mm 2,5 3,2 4,0 5,0 6,0 Length, mm 350 450 450 450 450 Arc voltage, V 22 23 23 24 24 Welding current, A 75-100 105-140 140-190 190-260 240-340 N. Kg weld metal/kg electrodes 0,62 0,65 0,65 0,68 0,69 B. No. of electrodes/kg weld metal 73,0 32,0 20,5 14,0 10,0 H. Kg weld metal/hour arc time 0,9 1,3 1,8 2,6 3,6 T. Burn-off time, s/electrode 55 86 97 100 103
OK 75.75 SMAW Type Lime-basic
OK 75.75 is an LMA electrode dried to a very low moisture content and suitable for the welding of high-strength, low-alloyed steels, at room temperature or with moderate preheating. Welding current DC+ Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E11018-G EN 757 E 69 4 Mn2NiCrMo B 42 H5
ABS E11018-G DB 10.039.19 RS 4Y62HH Sepros UNA 409819 VdTV 01028 CE EN 13479
C 0,06 Si 0,3 Mn 1,7 Cr 0,4 Ni <2.6 Mo 0,4 P 0,02 S 0,02 V 0,05
Redrying temperature, C 350 Redrying time, hours 2 Recovery 125%
Diameter, mm 2,0 2,5 3,2 4,0 5,0 Length, mm 300 350 450 450 450 Arc voltage, V 21 22 23 24 25 Welding current, A 50-75 70-110 100-150 135-200 180-260 N. Kg weld metal/kg electrodes 0,67 0,67 0,67 0,65 0,63 B. No. of electrodes/kg weld metal 120,0 66,0 31,5 21,0 12,0 H. Kg weld metal/hour arc time 0,70 1,0 1,4 1,9 2,50 T. Burn-off time, s/electrode 41 54 80 92 105
OK 76.16 SMAW Type Lime-basic
Basic, low-hydrogen electrode for the DC welding of creep-resistant steels of the 1.25% Cr, 0.5% Mo type, such as SA-387 Grade 11/A 335 P11.The weld metal has an extra-low impurity level . Welding current DC+(-)
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E8018-B2-H4R EN 1599 E Cr Mo 1 B 42 H5
C 0,07 Si 0,4 Mn 0,6 Cr 1,4 Mo 0,6
Yield stress, MPa 550 Tensile strength, MPa 620 Elongation, % 22 Elongation, % 22 Charpy V Test temps, C Impact values, J -20 70
Recovery 115%
Diameter, mm 2,5 3,2 4,0 Length, mm 350 350 350 Arc voltage, V 23 23 22 Welding current, A 70-110 95-150 130-190 N. Kg weld metal/kg electrodes 0,6 0,59 0,89 B. No. of electrodes/kg weld metal 74 48 30 H. Kg weld metal/hour arc time 0,65 1,07 1,55 T. Burn-off time, s/electrode 75 71 78
OK 76.18 SMAW Type Basic
OK 76.18 is an LMA electrode for welding creep-resistant steels of the 1.Cr0.5Mo type. The electrode welds with a quiet, stable arc and produces a minimum of spatter loss. OK 76.18 deposits a weld metal which is resistant to cracking as well as porosity. The scaling temperature of the weld metal is about 575C. Welding current DC(+-)
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.5 E8018-B2 EN 1599 ECrMo1 B 42 H5
ABS For high temperature applications BV UP CL DNV H10 for NV 1Cr0,5Mo DS EN 1599 Sepros SFS EN 1599 SS EN 1599 VdTV
C 0,08 Si 0,4 Mn 0,6 Cr 1,3 Mo 0,6
Yield stress, MPa 530 Tensile strength, MPa 620 Elongation, % 20 Elongation, % 20 Charpy V Test temps, C Impact values, J +20 55 -20 38 -40 19
Redrying temperature, C 350 Redrying time, hours 2 Recovery 115%
Diameter, mm 2,0 2,5 3,2 4,0 4,0 5,0 6,0 Length, mm 300 300 350 350 450 450 450 Arc voltage, V 22 24 25 - 27 28 30 Welding current, A 55-80 70-110 95-150 130-190 130-190 150-260 200-350 N. Kg weld metal/kg electrodes 0,58 0,58 0,59 - 0,64 0,64 0,64 B. No. of electrodes/kg weld metal 136,0 88,0 49,0 - 23,0 14,5 10,5 H. Kg weld metal/hour arc time 0,7 0,8 1,1 - 1,7 2,7 3,7 T. Burn-off time, s/electrode 40 52 65 - 90 95 93
OTELURI INOXIDABILE SI INALT ALIATE
OK 61.30 SMAW Type Acid-rutile
Extra-low carbon stainless steel electrode for welding steels of the 19 Cr 10 Ni-type. Also suitable for welding stabilized stainless steels of similar composition, except when full creep resistance of the base material is to be met. Welding current DC+, AC OCV 50 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 9 L R 1 2 SFA/AWS A5.4 E308L-17 Werkstoff Nr. 1.4316 CSA W48 E 308L-17
ABS Stainless CWB CSA W48 DB 30.039.02 DNV 308L Sepros UNA 409820 VdTV 00792 CE EN 13479
C <0,03 Si 0,75 Mn 0,9 Cr 19,5 Ni 10,0 Mo <0,5 Cu <0,5
Yield stress, MPa 430 Tensile strength, MPa 560 Elongation, % 43 Elongation, % 43 Ferrite content FN 3-10 Charpy V Test temps, C Impact values, J +20 70 -60 32
Redrying temperature, C 350 Redrying time, hours 2 Recovery 105
Diameter, mm 1,6 2,0 2,5 3,2 4,0 5,0 Length, mm 300 300 300 350 350 350 Arc voltage, V 27 29 31 31 32 33 Welding current, A 35-45 35-65 50-90 70-130 90-180 140-250 N. Kg weld metal/kg electrodes 0,55 0,55 0,55 0,60 0,60 0,60 B. No. of electrodes/kg weld metal 240 160 99 49 33 20 H. Kg weld metal/hour arc time 0,6 0,8 1,1 1,4 2,0 3,0 T. Burn-off time, s/electrode 24 29 36 54 60 60
OK 61.35 SMAW Type Basic
OK 61.35 is a basic, low-carbon, stainless electrode of the E308L type with very good welding properties in the vertical and overhead positions. The high impact toughness at cryogenic temperature (-196C) makes OK 61.35 excellent in LNG appl ications. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 9 L B 2 2 SFA/AWS A5.4 E308L-15 Werkstoff Nr. 1.4316
Sepros UNA 409820 UDT EN 1600 VdTV 04811
C <0,04 Si 0,5 Mn 1,7 Cr 19,0 Ni 10,0 Mo <0,3 Cu <0,3
Redrying temperature, C 200 Redrying time, hours 2 Recovery 100
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 22 25 27 26 Welding current, A 55-85 80-120 80-180 160-210 N. Kg weld metal/kg electrodes 0,61 0,61 0,61 0,51 B. No. of electrodes/kg weld metal 92 50 33 25 H. Kg weld metal/hour arc time 0,9 1,3 1,9 2,2 T. Burn-off time, s/electrode 37 54 58 66
OK 61.81 SMAW Type Rutile
Nb-stabilezed MMA-electrode for welding Nb- or Ti-stabilized stainless steel of the 19Cr10Ni-type. Welding current DC+, AC OCV 60 V
Classifications Approvals Typical all weld metal Typical mech. properties all weld metal composition, % SFA/AWS A5.4 E347-16 EN 1600 E 19 9 Nb R 3 2 Werkstoff Nr. 1.4551
DNV 347 CE EN 13479 Seproz UNA 054403
C 0,06 Si 0,8 Mn 1,55 Cr 20 Ni 10 Mo 0,3 Nb 1,00 Cu 0,3 P 0,025 S 0,020
Yield stress, MPa 560 Tensile strength, MPa 700 Elongation, % 31 Elongation, % 31 Ferrite content FN 6-12 Charpy V Test temps, C Impact values, J +20C 60 -10C 71
Redrying temperature, C 350 Redrying time, hours 2 Recovery 105-110
Diameter, mm 2,0 2,5 3,2 4,0 5,0 Length, mm 300 300 350 350 350 Arc voltage, V 26 29 23 24 25 Welding current, A 40-60 50-80 75-115 80-160 140-210 N. Kg weld metal/kg electrodes 0,60 0,59 0,60 0,60 0,60 B. No. of electrodes/kg weld metal 147 82 44 32 20 H. Kg weld metal/hour arc time 0,6 1,2 1,2 1,7 2,3 T. Burn-off time, s/electrode 39 36 66 66 78 Weight of rods/box, kg 1,1 2,1 3,4 5,2 8,0
OK 61.85 SMAW Type Basic
OK 61.85 is a basic coated, niobium stabilised electrode of the E347-type, specially designed for welding niobium- or titanium- stabilised steels. OK 61.85 has outstanding welding properties in the vertical and overhead positions, making it suitable for pipewelding, for example. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 9 Nb B 2 2 SFA/AWS A5.4 Sepros UNA 409820 VdTV 05663
C <0,07 Si 0,5 Mn 1,7 Cr 19,5 Yield stress, MPa 500 Tensile strength, MPa 620 Elongation, % 40
E347-15 Werkstoff Nr. 1.4551
Ni 10,0 Mo <0,3 Nb <1,0 Cu <0,3 Nb+ Ta 1,00
Elongation, % 40 Ferrite content FN 6-12 Charpy V Test temps, C Impact values, J +20 100 -60 70 -120 >32
Redrying temperature, C 200 Redrying time, hours 2 Recovery 100
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 25 23,3 23,5 23,1 Welding current, A 55-85 75-110 110-150 150-200 N. Kg weld metal/kg electrodes 0,60 0,62 0,61 0,61 B. No. of electrodes/kg weld metal 98 49 33 21 H. Kg weld metal/hour arc time 0,9 1,2 1,6 2,3 T. Burn-off time, s/electrode 42 64 70 76
OK 63.20 SMAW Type Acid-rutile
Rutile coated electrode for welding 18Cr12Ni3Mo-type steels. Also suitable for welding stabilized steels of similar composition. The electrode is especially designed for welding of thin walled pipes. Diameters 1.6-2.5mm. can be used in all positions including vertical down. Welding current DC+, AC OCV 50 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 12 3 L R 1 1 SFA/AWS A5.4 E316L-16 Werkstoff Nr 1.4430 CSA W48 E316L-16
CWB CSA W48 Sepros UNA 409820 VdTV 09716 CE EN 13479
C <0,03 Si 0,95 Mn 0,85 Cr 18,3 Ni 12,0 Mo 2,8 Cu <0,3
Yield stress, MPa 480 Tensile strength, MPa 590 Elongation, % 35 Elongation, % 35 Ferrite content FN 3-10 Charpy V Test temps, C Impact values, J
+20 56 -60 48
Redrying temperature, C 350 Redrying time, hours 2 Recovery 94-106
Diameter, mm 1,6 1,6 2,0 2,0 2,5 3,2 Length, mm 300 265 300 265 300 350 Arc voltage, V 23 23 25 22 22 26 Welding current, A 15-40 15-40 18-60 18-60 25-80 55- 110 N. Kg weld metal/kg electrodes 0,63 0,52 0,62 0,65 0,63 0,60 B. No. of electrodes/kg weld metal 227 249 152 167 96 52 H. Kg weld metal/hour arc time 0,3 0,3 0,5 0,6 0,8 1,2 T. Burn-off time, s/electrode 53 48 49 44 54 65
OK 63.30 SMAW Type Acid-rutile
Extra low carbon stainless steel electrode for welding steelss of the 18Cr 12Ni 2.8Mo-type. Also suitable for welding of stabilized stainless steels of similar composition, exept when the full creep resistance of the base metal is to be met. Welding current DC+, AC OCV 50 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 12 3 L R 1 2 SFA/AWS A5.4 E316L-17 Werkstoff Nr. 1.4430 CSA W48 E316L-17
ABS E316L-17 BV U.P. for chemical applications CWB CSA W48 DB 30.039.06 DNV 316L GL 4571 LR 316L Sepros UNA 409820 VdTV 00262 CE EN 13479
C <0,03 Si 0,75 Mn 0,9 Cr 18,0 Ni 12,0 Mo 2,8 Cu <0,2
Redrying temperature, C 350 Redrying time, hours 2 Recovery 110
Diameter, mm 1,6 2,0 2,5 2,5 3,2 4,0 5,0 Length, mm 300 300 300 350 350 350 350 Arc voltage, V 29 29 29 30 30 32 32 Welding current, A 30-45 45-65 45-90 45-80 60-125 70-190 100-280 N. Kg weld metal/kg electrodes 0,56 0,60 0,56 0,56 0,55 0,56 0,56 B. No. of electrodes/kg weld metal 250 147 96 83 52 34 21 H. Kg weld metal/hour arc time 0,4 0,6 1,1 1,1 1,4 2,0 3,0 T. Burn-off time, s/electrode 37 39 45 41 57 57 63
OK 63.35 SMAW Type Basic
Stainless steel electrode for welding steels of the CrNiMo 17-12-3 tpe. It can also be used for welding certain air hardening steels, e.g armour steels. Very suitable for cryogenic applications. ' Requirement for lateral expansion 0.38mm at -196 C can be met on special order. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 12 3 L B 2 2 SFA/AWS A5.4 E316L-15 Werkstoff Nr. 1.4430
ABS Stainless VdTV 04812 CE EN 13479 Seproz UNA 054403
C 0,04 Si 0,45 Mn 1,65 Cr 18,5 Ni 12 Mo 2,75 Cu 0,3 P 0,025 S 0,020
Yield stress, MPa 430 Tensile strength, MPa 520 Elongation, % 40 Elongation, % 30 Ferrite content FN 3-8 Weld metal hardness, a w HV 190-215 Charpy V Test temps, C Impact values, J +20 95 -60 75 -120 60 -196 35
Redrying temperature, C 200 Redrying time, hours 2 Recovery 110
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 24 24 24 24 Welding current, A 55-85 80-120 80-180 150-200 N. Kg weld metal/kg electrodes 0,63 0,63 0,62 0,62 B. No. of electrodes/kg weld metal 91 47 32 20 H. Kg weld metal/hour arc time 0,9 1,3 1,8 2,6 T. Burn-off time, s/electrode 42 58 63 68 Weight of rods/box, kg 1,7 3,4 5,2 -
OK 63.80 SMAW Type Acid-rutile
Acid rutile covered MMA-electrode for welding Nb-or Ti stabilized steels of the CrNiMo 18-12-3 type. Welding current DC+, AC OCV 50 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 12 3 Nb R 3 2 SFA/AWS A5.4 E318-17 Werkstoff Nr. 1.4576
VdTV 00639 CE EN 13479
C <0,03 Si 0,8 Mn 0,9 Cr 18,0 Ni 12,0 Mo 2,8 Nb <0,6 Cu <0,3 Nb+ Ta 0,60
Yield stress, MPa 500 Tensile strength, MPa 614 Elongation, % 38 Elongation, % 38 Ferrite content FN 6-12 Charpy V Test temps, C Impact values, J +20 55 -60 41
Redrying temperature, C 350 Redrying time, hours 2 Recovery 110
Diameter, mm 2,0 2,5 3,2 4,0 Length, mm 300 300 350 350 Arc voltage, V 29 30 32 33 Welding current, A 45-65 60-90 80-120 120-170 N. Kg weld metal/kg electrodes 0,56 0,56 0,61 0,61 B. No. of electrodes/kg weld 155 97 48 32 metal H. Kg weld metal/hour arc time 0,8 1,1 1,4 2,1 T. Burn-off time, s/electrode 29 35 54 55
OK 63.85 SMAW Type Lime-basic
OK 63.85 is a niobium-stabilised 18Cr12Ni2.8Mo electrode for welding steels of similar composition. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 19 12 3 Nb B 4 2 SFA/AWS A5.4 E 318-15 Werkstoff Nr. 1.4576
Sepros UNA 409820 VdTV 05662
C <0,06 Si 0,5 Mn 1,7 Cr 18,5 Ni 12,0 Mo 2,8 Nb <1,0 Cu <0,5 Nb+ Ta 1,00
Yield stress, MPa 490 Tensile strength, MPa 640 Elongation, % 35 Elongation, % 35 Ferrite content FN 5-10 Charpy V Test temps, C Impact values, J +20 65 -120 45
Redrying temperature, C 200 Redrying time, hours 2 Recovery 115
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 22 23 24 26 Welding current, A 50-80 65-120 75-160 145-210 N. Kg weld metal/kg electrodes 0,66 0,64 0,64 0,61 B. No. of electrodes/kg weld metal 81 43 28 19 H. Kg weld metal/hour arc time 1,0 1,5 2,0 2,7 T. Burn-off time, s/electrode 45 58 64 72
OK 67.13 SMAW Type Basic-rutile
OK 67.13 is an austenitic, stainless-steel electrode for welding 25Cr20Ni steels. The weld metal resists scaling up to 1100-1150C and does not contain any measureable ferrite. OK 67.13 can also be used for welding certain air-hardening steels such as armour plate and for welding stainless to unalloyed steel. Welding current DC+, AC OCV 65 V
EN 1600 E 25 20 R 1 2 SFA/AWS A5.4 E310-16 Werkstoff Nr. 1.4842
C 0,12 Si 0,5 Mn 2,0 Cr 26,0 Ni 21,0 Cu <0,2
Yield stress, MPa 560 Tensile strength, MPa 600 Elongation, % 35 Elongation, % 35 Ferrite content FN 0 Charpy V Test temps, C Impact values, J +20 60
Redrying temperature, C 250 Redrying time, hours 2 Recovery 95-100
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 21 24 28 31 Welding current, A 50-85 65-120 70-160 150-220 N. Kg weld metal/kg electrodes 0,51 0,51 0,51 0,54 B. No. of electrodes/kg weld metal 101,0 53,0 34,0 20,5 H. Kg weld metal/hour arc time 0,8 1,2 1,7 2,6 T. Burn-off time, s/electrode 42 58 61 67
OK 67.15 SMAW Type Lime-basic
Basic coated MMA-electrode for welding 25Cr 20Ni-steels. Also suitable for welding armour steels, austenitic manganese steels and for joining of dissimilar steels. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 25 20 B 2 2 DB 30.039.01 Sepros UNA 409820 C 0,12 Si 0,5 Yield stress, MPa 410 Tensile strength, MPa 590
SFA/AWS A5.4 E310-15 Werkstoff Nr. 1.4842
VdTV 01025 CE EN 13479
Mn 2,2 Cr 26,0 Ni 21,0 Mo <0,5 Cu <0,5
Elongation, % 35 Elongation, % 35 Ferrite content FN 0 Charpy V Test temps, C Impact values, J +20 100
Redrying temperature, C 200 Redrying time, hours 2 Recovery 100-105
Diameter, mm 2,0 2,5 3,2 4,0 5,0 Length, mm 300 300 350 350 350 Arc voltage, V 24 25 25 26 26 Welding current, A 45-55 50-85 60-115 70-160 130-200 N. Kg weld metal/kg electrodes 0,62 0,61 0,59 0,59 0,60 B. No. of electrodes/kg weld metal 162 96 50 28 22 H. Kg weld metal/hour arc time 0,6 0,9 1,2 1,8 2,5 T. Burn-off time, s/electrode 36 40 60 62 65
OK 67.50 SMAW Type Acid-rutile
Acid rutile coated MMA-electrode for welding of austenitic-ferritic stainless steels of CrNiMoN 22 5 3 -and CrNiN 23 4-types. Welding current DC+, AC OCV 60 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 22 9 3 N L R 3 2 SFA/AWS A5.4 E2209-17 Werkstoff Nr. 1.4462 CSA W48 E2209-17
ABS For welding duplex steels BV 2209 CWB CSA W48 DNV For duplex SS GL 4462 RINA 2209 Sepros UNA 409820 C <0,03 Si 0,75 Mn 0,9 Cr 22,5 Ni 9,5 Mo 3,0 Cu <0,3 N 0,16
Yield stress, MPa 660 Tensile strength, MPa 857 Elongation, % 25 Elongation, % 25 Ferrite content FN 25-40 Charpy V Test temps, C Impact values, J
VdTV 04368 CE EN 13479
+20 50 -30 41
Redrying temperature, C 350 Redrying time, hours 2 Recovery 0-108
Diameter, mm 2,0 2,5 3,2 4,0 5,0 Length, mm 300 300 350 350 350 Arc voltage, V 29 27 28 29 30 Welding current, A 30-65 50-90 80-120 100-160 150-220 N. Kg weld metal/kg electrodes 0,55 0,58 0,58 0,58 0,58 B. No. of electrodes/kg weld metal 152 91 47 32 20 H. Kg weld metal/hour arc time 0,7 1,0 1,4 1,9 2,8 T. Burn-off time, s/electrode 33 38 55 59 64
OK 67.75 SMAW Type Basic
OK 67.75 is a basic coated, stainless electrode for welding steels of the 24Cr13Ni type, for welding transition layers when surfacing mild steel with stainless, for joining dissimilar steels and welding root runs in the stainless side of clad steels. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 23 12 L B 4 2 SFA/AWS A5.4 E309L-15 Werkstoff Nr. 1.4332
ABS Stainless DNV 309 LR SS to C/Mn Steels Sepros UNA 409820 UDT EN 1600 VdTV 00633
C <0,04 Si 0,5 Mn 2,2 Cr 24,0 Ni 13,0 Mo <0,5 Cu <0,3
Yield stress, MPa 470 Tensile strength, MPa 600 Elongation, % 35 Elongation, % 35 Ferrite content FN 12-22 Charpy V Test temps, C Impact values, J +20 75 -80 55
Redrying temperature, C 200 Redrying time, hours 2 Recovery 120
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 22 24 26 27 Welding current, A 50-80 80-110 100-150 160-220 N. Kg weld metal/kg electrodes 0,73 0,73 0,73 0,73 B. No. of electrodes/kg weld metal 78,0 39,0 25,0 16,5 H. Kg weld metal/hour arc time 1,1 1,5 2,3 3,4 T. Burn-off time, s/electrode 42 60 62 65
OK 68.15 SMAW Type Lime-basic
OK 68.15 is a stainless-steel electrode which deposits a ferritic 13Cr weld metal. OK 68.15 is designed for welding steels of similar composition, when CrNi-alloyed austenitic stainless steel electrodes cannot be used, e.g. when the structure is going to be exposed to aggressive sulphuric gases. Depending on the welding parameters, the structure and consequently the mechanical properties of untreated weld metal can vary within fairly large limits. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 13 B 4 2 SFA/AWS A5.4 E410-15 Werkstoff Nr. 1.4009
Sepros UNA 409820 UDT EN 1600
C <0,06 Si <0,7 Mn <1,0 Cr 12,5 Ni <0,6 Mo <0,5 Cu <0,2
Redrying temperature, C 200 Redrying time, hours 2 Recovery 108-118
Diameter, mm 2,5 3,2 4,0 Length, mm 350 450 450 Arc voltage, V 25 25 30 Welding current, A 65-115 90-160 120-220 N. Kg weld metal/kg electrodes 0,62 0,63 0,57 B. No. of electrodes/kg weld metal 73 33 24 H. Kg weld metal/hour arc time 1,0 1,5 2,0 T. Burn-off time, s/electrode 48 71 73
OK 69.33 SMAW Type Basic-rutile
OK 69.33 is a stainless-steel electrode which deposits a fully austenitic weld metal with increased resistance to sulphuric acid. The weld metal of OK 69.33 also has good resistance to intergranular and pitting corrosion. Welding current AC, DC+ OCV 65 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal EN 1600 E 20 25 5 Cu N L R 3 2 SFA/AWS A5.4 E385-16 Werkstoff Nr. 1.4519
Sepros UNA 409820 VdTV 02723 CE EN 13479
C <0,03 Si 0,5 Mn 1,3 Cr 20,5 Ni 25,5 Mo 4,8 Cu 1,6 N 0,15
Yield stress, MPa 400 Tensile strength, MPa 590 Elongation, % 35 Elongation, % 35 Ferrite content FN 0 Charpy V Test temps, C Impact values, J +20 80 -140 45
Redrying temperature, C 250 Redrying time, hours 2 Recovery 115-120
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 24 27 29 31 Welding current, A 60-85 85-130 95-180 160-240 N. Kg weld metal/kg electrodes 0,60 0,58 0,51 0,51 B. No. of electrodes/kg weld metal 91 41 30 19 H. Kg weld metal/hour arc time 0,9 1,5 1,9 2,5 T. Burn-off time, s/electrode 44 60 64 78
ELECTROZI PE BAZA DE ALUMINIU
OK 96.20 SMAW Type Chloride and fluoride salt
OK 96.20 is an electrode for welding rolled, weldable aluminium alloys, such as aluminium-magnesium and aluminium-manganese alloys. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal DIN 1732 EL-AlMn1
Si <0,5 Mn 1,3 Al 97,5 Fe <0,7
Redrying temperature, C 80 Redrying time, hours 1 Recovery 95
Diameter, mm 2,5 3,2 4,0 Length, mm 350 350 350 Arc voltage, V 22 22 22 Welding current, A 50-90 70-110 90-130
OK 96.40 SMAW Type Chloride and fluoride salt
A coated electrode suitable for welding AlMnSi alloys such as EN - AW 6060/6063, 6005, 6201. Also suitable for welding AlSi5Cu and AlSi7 type castings. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal DIN 1732 EL-AlSi5
Si 5,0 Al 94,0 Fe <0,4
Redrying temperature, C 80 Redrying time, hours 1
Diameter, mm 2,5 3,2 4,0 Length, mm 350 350 350 Arc voltage, V 22 22 22 Welding current, A 50-90 70-110 90-130
OK 96.50 SMAW Type Chloride and fluoride salt
An electrode for welding cast aluminium alloys. Also suitable for welding rolled aluminium alloys or joining them to cast items. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal DIN 1732 EL-AlSi12
Si 12,3 Al 87,5 Fe <0,5
Redrying temperature, C 80 Redrying time, hours 1 Recovery 90
Diameter, mm 2,5 3,2 4,0 Length, mm 350 350 350 Arc voltage, V 22 22 22 Welding current, A 50-90 70-110 90-130
ALIAZE PE BAZA DE NICHEL
OK 92.05 SMAW Type Lime-basic
OK 92.05 is a stick electrode for joining commercial pure nickel in wrought and cast forms. It can also be used to join dissimilar metals such as nickel to steel, nickel to copper and copper to steel. Moreover, this electrode can be used for surfacing steel. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.11 ENi-1 EN ISO 14172 E Ni 2061 (NiTi3)
C 0,04 Si 0,7 Mn 0,4 Ni >92 Cu <0,2 Al <0,1 Ti 1,5 Fe 0,4
Redrying temperature, C 250 Redrying time, hours 2
Diameter, mm 2,5 3,2 4,0 Length, mm 300 350 350 Arc voltage, V 23 25 27 Welding current, A 70-95 90-135 120-180 N. Kg weld metal/kg electrodes 0,55 0,55 0,45 B. No. of electrodes/kg weld metal 96 53 42 H. Kg weld metal/hour arc time 0,8 1,2 1,5 T. Burn-off time, s/electrode 47 56 59
OK 92.26 SMAW Type Basic
A nickel-based electrode for welding nickel alloys such as Inconel 600 and similar Inconel alloys, cryogenic steels, martensitic to austenitic steels, dissimilar steels, heat-resistant steels and castings with limited weldability. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.11 ENiCrFe-3 EN ISO 14172 E Ni 6182 (NiCr15Fe6Mn)
ABS ENiCrFe-3 Sepros UNA 409820
C 0,03 Si 0,5 Mn 6,6 Cr 15,8 Ni 67 Nb 1,7 Cu <0,5 Ti <0,5 Ta <0,3 Fe 8,8
Yield stress, MPa 410 Tensile strength, MPa 640 Elongation, % 40 Elongation, % 40 Ferrite content FN 0 Charpy V Test temps, C Impact values, J +20 100 -196 80
Redrying temperature, C 200 Redrying time, hours 2 Recovery 110
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 22 23 24 25 Welding current, A 45-70 70-105 90-130 120-170 N. Kg weld metal/kg electrodes 0,63 0,62 0,64 0,64 B. No. of electrodes/kg weld metal 88 57 31 20 H. Kg weld metal/hour arc time 0,9 1,2 2,0 2,7 T. Burn-off time, s/electrode 50 60 60 68
OK 92.45 SMAW Type Basic
OK 92.45 is a NiCrMoNb-based electrode for welding nickel alloys of the same or similar type, like Inconel 625, and for welding 5Ni and 9Ni steel. OK 92.45 is also suitable for welding UNS S31254 steel. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.11 ENiCrMo-3 EN ISO 14172 E Ni 6625 (NiCr22Mo9Nb)
VdTV 06833 Seproz UNA 054403
C 0,05 Si 0,5 Mn 0,50 Cr 21,5 Ni 63,9 Mo 9,25 Nb 3,575 Cu 0,3 Al 0,4 Fe 5,0 P 0,020 S 0,010
Yield stress, MPa 500 Tensile strength, MPa 780 Elongation, % 35 Elongation, % 35 Ferrite content FN 0 Charpy V Test temps, C Impact values, J +20 70 -196 50
Redrying temperature, C 200 Redrying time, hours 2 Recovery 105
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 300 350 350 350 Arc voltage, V 23 25 27 24 Welding current, A 55-75 65-100 80-140 80-140 N. Kg weld metal/kg electrodes 0,55 0,56 0,58 0,58 B. No. of electrodes/kg weld metal 100 49 33 21 H. Kg weld metal/hour arc time 0,9 1,4 1,9 2,1 T. Burn-off time, s/electrode 40 52 57 72 Weight of rods/box, kg 1,8 3,6 5,3 7,8
OK 92.55 SMAW Type Basic
OK 92.55 is an all-positional, basic coated electrode which deposits a NiCr-based alloy with additions of Mo, W and Nb. The electrode is specifically designed for welding 9%Ni steels for cryogenic applications down to -196C. Welding current AC, DC+ - OCV 55 V
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.11 ENiCrMo-6 EN ISO 14172 E Ni 6620 (NiCr14Mo7Fe)
ABS ENiCrMo-6 BV N50 DNV For welding NV 1,5Ni to NV 9 Ni
C 0,08 Si 0,55 Mn 3 Cr 13,0 Ni 69 Mo 6,2 W 1,6 Nb 1,3 Cu <0,3 Fe 5,0
Yield stress, MPa >430 Tensile strength, MPa >690 Elongation, % >35 Elongation, % >35 Ferrite content FN 0 Charpy V Test temps, C Impact values, J -196 >70
Redrying temperature, C 300 Redrying time, hours 1-2 Recovery 150-155
Diameter, mm 2,5 3,2 4,0 5,0 Length, mm 350 350 350 350 Arc voltage, V 23 22 22 23 Welding current, A 65-115 70-150 120-200 150-240 N. Kg weld metal/kg electrodes 0,70 0,66 0,67 0,68 B. No. of electrodes/kg weld metal 55 34 23 14 H. Kg weld metal/hour arc time 1,1 1,5 1,9 2,8 T. Burn-off time, s/electrode 70 68 82 91 Select region/country Cutare site | Hart site | Termeni i condiii | Copyright 2006 ESAB
OK 92.59 SMAW Type Basic
OK 92.59 is designed for welding alloy 59, C-276 and 625 Ni-based materials. It is also suitable for welding superaustenitic steels like AISI/ASTM S31254 and S32654. Welding current DC+
Classifications Approvals Typical all weld metal composition, % Typical mech. properties all weld metal SFA/AWS A5.11 ENiCrMo-13 EN ISO 14172 E Ni 6059 (NiCr23Mo16)
C <0,02 Si <0,2 Mn <0,2 Cr 23,0 Ni 62,0 Mo 15,8 Fe <1,0
Yield stress, MPa 430 Tensile strength, MPa 770 Elongation, % 40 Elongation, % 40 Ferrite content FN 0 Charpy V Test temps, C Impact values, J -60 70 -196 60
Redrying temperature, C 200 Redrying time, hours 2
Diameter, mm 2,5 3,2 4,0 Length, mm 300 350 350 Arc voltage, V 20 21 22 Welding current, A 50-70 60-90 80-120