Documente Academic
Documente Profesional
Documente Cultură
1
ETAPELE DE REALIZARE A APLICAŢIEI:
3. Pentru a vizualiza spaţiul de desenare se utilizează comanda ZOOM cu opţiunea ALL, astfel:
Command: ZOOM
2
Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: ALL
4. Se desenează chenarul formatului cu linie de grosime 1 (opţiunea Width, 1) utilizând comanda
PLINE, astfel:
Command: PLINE
Specify start point: 10,10
Current line-width is 0.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: W
Specify starting width <0.0000>: 1
Specify ending width <1.0000>: 1
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: @400,0
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,277
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-400,0
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: CLOSE
Se obţine chenarul din fig. 2.3.
3
of SE ALEGE COLŢUL DIN DREAPTA - JOS AL FORMATLUI
Current line-width is 1.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: @0,50
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @-180,0
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @0,-50
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: CLOSE
4
Fig.2.5. Deplasarea sistemului de coordonate.
7. Se trasează cele două linii centrale ortogonale ale indicatorului. Pentru această
operaţie se utilizează comanda PLINE şi opţiunea PERpendicular (fig.2. 6).
Command: PLINE
Specify start point: 80,50
Current line-width is 1.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: PER
to SE ALEGE BAZA INDICATORULUI
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: [ENTER]
Command: PLINE
Specify start point: 0,30
Current line-width is 1.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: PER
to SE ALEGE LATURA DIN DREAPTA A INDICATORULUI
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: [ENTER]
5
Fig.2.6. Cele două linii centrale ale indicatorului.
8. În dreptunghiul din stânga-jos se trasează prima linie subţire utilizând comanda LINE
şi modul OSNAP PERpendicular (fig.2.7).
Command: LINE
Specify first point: 0, 5
Specify next point or [Undo]: PER
to
Specify next point or [Undo]: [ENTER]
6
Fig. 2.8 Aplicarea comenzii OFFSET.
10. Utilizând comanda LINE se trasează cele două linii verticale subţiri în dreptunghiul din
stânga-jos (fig. 10).
Command: LINE
Specify first point: 30,0
Specify next point or [Undo]: PER
to SE ALEGE LINIA GROASA ORIZONTALA (fig.2. 9)
Specify next point or [Undo]: [ENTER]
Command: LINE
Specify first point: 60,0
Specify next point or [Undo]: PER
to SE ALEGE LINIA GROASA ORIZONTALA (fig.2.9)
7
Specify next point or [Undo]: [ENTER]
11. Se trasează cele două linii verticale groase utilizând comanda PLINE (fig.2.11).
Command: PLINE
Specify start point: 95,0
Current line-width is 1.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: PER
to SE ALEGE LINIA GROASA ORIZONTALA
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: [ENTER]
Command: PLINE
Specify start point: 160,50
Current line-width is 1.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: PER
to SE ALEGE LINIA GROASA ORIZONTALA
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: [ENTER]
8
Fig.2.11 Cele două linii verticale groase.
EXERCIŢII PROPUSE
9
10