Documente Academic
Documente Profesional
Documente Cultură
FIŞĂ DE DOCUMENTARE
M2 - APLICAŢII CAD
CLASA A XI A
DENUMIREA TEMEI: TEŞIREA ŞI RACORDAREA ÎN 3D
Particularităţi de aplicare a comenzilor FILLET şi CHAMFER. Comanda FILLET poate fi utilizată şi în spaţiul
tridimensional, între obiecte coplanare care nu aparţin planului curent XY. AutoCAD determină planul lor comun
şi apoi aplică operaţia de racordare a contururilor selectate în acest plan.
Aplicarea comenzii FILLET pe două obiecte coplanare nesituate în planul XY al sistemului curent de coordonate.
Comanda FILLET poate fi aplicată şi pe obiecte solide. Aplicarea este posibilă pe muchiile aceluiaşi solid,
nefiind admisă realizarea unei racordări între obiecte solide distincte. La selectarea unui solid, opţiunile
comenzii FILLET se modifică adecvat: Select an edge or [Chain/Radius]. Se poate astfel selecta succesiv fiecare
muchie din setul supus rotunjirii, sau se poate opta pentru Chain, spre a indica un lanţ de muchii.
Aplicarea comenzii FILLET pe un obiect solid. În funcţie de natura muchiei selectate, rotunjirea se realizează cu
îndepărtare de material, pe muchii exterioare, respectiv cu adaos de material pe muchii intermediare.
Comanda CHAMFER poate fi aplicată pe muchiile unui obiect dar nu şi între solide diferite. Comanda iîşi
adaptează opţiunile pentru lucrul în 3D. În primă fază, se solicită suprafaţa în raport cu care se realizează teşirea,
apoi cele două distanţe de teşire şi, în al treilea pas, se cere precizarea muchiei care va fi teşita. Prin optiunea
"Loop", pot fi indicate toate muchiile unui contur închis. Teşirea se poate realiza cu adaos de material, dacă se
aplică pe muchii intermediare, sau cu indepărtare de material, dacă se aplică pe muchii exterioare.
1
Aplicarea comenzii CHAMFER pe un obiect solid
1.
Command: extrude
Current wire frame density: ISOLINES=4
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects: 1 found, 4 total
Select objects: 1 found, 5 total
Select objects:
Specify height of extrusion or [Path]: 20
Specify angle of taper for extrusion <0>:
Command: HIDE
Regenerating model.
3
CREAREA CILINDRULUI INTERIOR
Command: CYLINDER
Current wire frame density: ISOLINES=4
Specify center point for base of cylinder or [Elliptical] <0,0,0>:
Specify radius for base of cylinder or [Diameter]: D
Specify diameter for base of cylinder: 50
Specify height of cylinder or [Center of other end]: 100
Command:
CYLINDER
Current wire frame density: ISOLINES=4
Specify center point for base of cylinder or [Elliptical] <0,0,0>:
Specify radius for base of cylinder or [Diameter]: D
Specify diameter for base of cylinder: 30
Specify height of cylinder or [Center of other end]: 100
OBTINEREA SOLIDULUI
Command: UNION
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects
Command: SUBTRACT
Select solids and regions to subtract from ..
Select objects: 1 found
Select objects:
Select solids and regions to subtract ..
4
Select objects: 1 found
Select objects:
Command: ZOOM
Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window]<realtime>: EXTENS
ofPress ESC or ENTER to exit, or right-click to display shortcut menu.
Command: HIDE
Regenerating model.
5
Select objects:
Command: HIDE
Regenerating model.
RACORDAREA
Command: FILLET
Current settings: Mode = TRIM, Radius = 10.0000
Select first object or [Polyline/Radius/Trim]:
Enter fillet radius <10.0000>: 5
Select an edge or [Chain/Radius]:
Select an edge or [Chain/Radius]:
2 edge(s) selected for fillet.
Command: HIDE
Regenerating model.
TESIREA
Command: CHAMFER
(TRIM mode) Current chamfer Dist1 = 10.0000, Dist2 = 3.0000
Select first line or [Polyline/Distance/Angle/Trim/Method]:
Base surface selection...
Enter surface selection option [Next/OK (current)] <OK>:
Specify base surface chamfer distance <10.0000>: 3
Specify other surface chamfer distance <3.0000>:
Select an edge or [Loop]: Select an edge or [Loop]:
Command: HIDE
Regenerating model.
6
Command- SHADE
SECTIUNE DUPA ZX
Command: SLICE
Select objects: 1 found
Select objects:
Specify first point on slicing plane by [Object/Zaxis/View/XY/YZ/ZX/3points]
<3points>: ZX
Specify a point on the ZX-plane <0,0,0>:
Specify a point on desired side of the plane or [keep Both sides]:
Command: HIDE
Regenerating model.
Command: _shademode Current mode: 2D wireframe
nter option [2D wireframe/3D
wireframe/Hidden/Flat/Gouraud/fLat+edges/gOuraud+edges] <2D wireframe>: _f
7
Pentru obţinera modelului solid s-au folosit următoarele comenzi:
Stabilirea marginilor desenului:
Regenerating model.
AutoCAD menu utilities loaded.
Command: limits
Reset Model space limits:
Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0
Specify upper right corner <420.0000,297.0000>: 210,297
Command: grid
Specify grid spacing(X) or [ON/OFF/Snap/Aspect] <10.0000>: 0n
Requires a distance, numberX, or option keyword.
Specify grid spacing(X) or [ON/OFF/Snap/Aspect] <10.0000>: 10
Command: snap
Specify snap spacing or [ON/OFF/Aspect/Rotate/Style/Type] <10.0000>: on
Command: snap
Specify snap spacing or [ON/OFF/Aspect/Rotate/Style/Type] <10.0000>: on
Command: snap
Specify snap spacing or [ON/OFF/Aspect/Rotate/Style/Type] <10.0000>: 1
Command: zoom
Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: all
Regenerating model.
8
Specify radius of circle or [Diameter]: 3.5
Command: -array
Select objects: l
1 found
Select objects: 1 found (1 duplicate), 1 total
Select objects: p
1 found, 2 total
Select objects:
Enter the type of array [Rectangular/Polar] <R>: p
Specify center point of array: 77,110
Rotate arrayed objects? [Yes/No] <Y>:
Command: vpoint
Current view direction: VIEWDIR=0.0000,0.0000,1.0000
Specify a view point or [Rotate] <display compass and tripod>: -1,-1,1
Regenerating model.
Command: extrude
Current wire frame density: ISOLINES=4
Select objects: all
8 found
Select objects: 8
Specify opposite corner: 0
0 found
Select objects: hide
Select objects:
Specify height of extrusion or [Path]: 8
Specify angle of taper for extrusion <0>: 0
Command: hide
9
Regenerating model.
Command: subtract
Select solids and regions to subtract from ..
Select objects: 113.5,110
Specify opposite corner: *Cancel*
0 found
Select objects: 1 found
Select objects:
Select solids and regions to subtract ..
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects: 1 found, 4 total
Select objects:
Command: hide
Regenerating model.
Command: cylinder
Current wire frame density: ISOLINES=4
Specify center point for base of cylinder or [Elliptical] <0,0,0>: 77,110,0
Specify radius for base of cylinder or [Diameter]: 18.5
Specify height of cylinder or [Center of other end]: 57.5
Command: cylinder
Current wire frame density: ISOLINES=4
Specify center point for base of cylinder or [Elliptical] <0,0,0>: 77,110,0
Specify radius for base of cylinder or [Diameter]: 12.5
Specify height of cylinder or [Center of other end]: 57.5
Command: union
Select objects: Specify opposite corner: 1 found
Select objects:
At least 2 solids or coplanar regions must be selected.
Command: Regenerating model.
Command: hide
10
Regenerating model.
Command: '_zoom
Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>:
Command: hide
Regenerating model.
Command: ucs
Current ucs name: *WORLD*
Enter an option [New/Move/orthoGraphic/Prev/Restore/Save/Del/Apply/?/World]
<World>: n
Specify origin of new UCS or [ZAxis/3point/OBject/Face/View/X/Y/Z] <0,0,0>:
77,110,38
Command: ucs
Current ucs name: *NO NAME*
Enter an option [New/Move/orthoGraphic/Prev/Restore/Save/Del/Apply/?/World]
<World>: y
Specify rotation angle about Y axis <90>: -90
Command: ucsicon
Enter an option [ON/OFF/All/Noorigin/ORigin] <ON>: or
Command: cylinder
Current wire frame density: ISOLINES=4
Specify center point for base of cylinder or [Elliptical] <0,0,0>:
Specify radius for base of cylinder or [Diameter]: 10
Specify height of cylinder or [Center of other end]: 36.5
Command: cylinder
Current wire frame density: ISOLINES=4
Specify center point for base of cylinder or [Elliptical] <0,0,0>:
Specify radius for base of cylinder or [Diameter]: 6
Specify height of cylinder or [Center of other end]: 36.5
Command: union
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Command: hide
Regenerating model.
Command: union
Select objects: Specify opposite corner: 1 found
11
Select objects:
At least 2 solids or coplanar regions must be selected.
Command: Regenerating model.
Command:UNION
Select objects:
Command: hide
Regenerating model.
Command: subtract
Select solids and regions to subtract from ..
Command: hide
Regenerating model.
Command: CHAMFER
(TRIM mode) Current chamfer Dist1 = 2.0000, Dist2 = 10.0000
Select first line or [Polyline/Distance/Angle/Trim/Method]:
Base surface selection...
Enter surface selection option [Next/OK (current)] <OK>:
Specify base surface chamfer distance <2.0000>: 2
Specify other surface chamfer distance <10.0000>: 2
Select an edge or [Loop]: Select an edge or [Loop]:
12
Command: hide
Regenerating model
Command: fillet
Current settings: Mode = TRIM, Radius = 10.0000
Select first object or [Polyline/Radius/Trim]:
Enter fillet radius <10.0000>: 2
Select an edge or [Chain/Radius]:
Edge has already been picked.
Select an edge or [Chain/Radius]:
1 edge(s) selected for fillet.
Command: hide
Regenerating model.
Command: SHADE
Command: slice
13
Select objects: l
1 found
Select objects:
Specify first point on slicing plane by [Object/Zaxis/View/XY/YZ/ZX/3points]
<3points>: zx
Specify a point on the ZX-plane <0,0,0>:
Specify a point on desired side of the plane or [keep Both sides]:
The point should not be on the slicing plane.
Specify a point on desired side of the plane or [keep Both sides]:
Command: hide
Regenerating model
Command: SHADE
Regenerating model.
14
that it needs.
C:\Program Files\AutoCAD 2002\AcPltStamp.arx cannot find a dll or other file
that it needs.
C:\Program Files\AutoCAD 2002\AcToday.arx cannot find a procedure that it needs.
AutoCAD menu utilities loaded.
Command: _ucs
Current ucs name: *WORLD*
Enter an option [New/Move/orthoGraphic/Prev/Restore/Save/Del/Apply/?/World]
<World>: _move
Specify new origin point or [Zdepth]<0,0,0>:
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0
Specify radius of circle or [Diameter] <42.0000>: 42
Command: Specify opposite corner: *Cancel*
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0
Specify radius of circle or [Diameter] <42.0000>: 36
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,0
Specify radius of circle or [Diameter] <36.0000>: 30
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,60
Specify radius of circle or [Diameter] <30.0000>: 10
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,60
Specify radius of circle or [Diameter] <10.0000>: 20
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,-60
Specify radius of circle or [Diameter] <20.0000>: 10
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 0,-60
Specify radius of circle or [Diameter] <10.0000>: 20
Command: _trim
Current settings: Projection=UCS Edge=None
15
A rezultat aşa cum se observă în figură, profilul unei flanşe de prindere, situată la baza piesei. Conturul exterior,
format din cele 4 linii şi patru arce de cerc, se extrudează cu valoarea de 10 unităţi. Pentru a fi posibilă aplicarea
comenzii EXTRUDE conturul trebuie să devină polilinie. Astfel, cele 8 elemente geometrice ( liniile şi arcele de
cerc) care îl formează, sunt combinate într-o polilinie utilizând comanda PEDIT cu opţiunea JOIN:
Command: pedit
Select polyline:
Object selected is not a polyline
Do you want to turn it into one? <Y>
Enter an option [Close/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype
gen/Undo]: join
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
7 segments added to polyline
Command: extrude
Current wire frame density: ISOLINES=4
Specify height of extrusion or [Path]: 10
Specify angle of taper for extrusion <0>:
De asemenea şi cele 2 cercuri mici vor fi extrudatede diametru 20 mm, cu aceeaşi valoare de 10 unităţi, pentru a fi
extrase( cu comanda SUBTRACT) din corpul solid obţinut în urma extrudării anterioare a profilului. Toate
operaţiile necesare în etapa curentă se desfăşoarăp în portul devedere isometric SW Isometric View, obţinându-se
corpul solid prezentat în figura de mai sus.
Se observă că în această etapă, cele două cercuri concentrice poziţionate în interiorul profilului nu au fost
extrudate.
În portul de vedere orthogonal Left View se trasează o polilinie formată din două linii de lungime 100 unităţi
fiecare şi un arc de rază 60 unităţi după cum se observă în imaginea de mai jos:
16
Specify next point or [Close/Undo]: *Cancel*
Command: _fillet
Current settings: Mode = TRIM, Radius = 10.0000
Select first object or [Polyline/Radius/Trim]: r
Specify fillet radius <10.0000>: 60
Command: _fillet
Current settings: Mode = TRIM, Radius = 60.0000
Select first object or [Polyline/Radius/Trim]:
Select second object:
Pentru a uşura procesul de desenare a poliliniei se recomadă rotirea şi repoziţionarea sistemului de coordinate
current, acesta fiind de asemnea reprezentat în figură. Această polilinie va servi drept o curbă de extrudare
( PATH) pentru cele două cercuri concentrice de diametru 60 mm şi respective 72 mm ) situate la baza flanşei,
obţinându-se corpul solid 3 D din figura de mai jos.
*
Command: pedit
Select polyline:
Object selected is not a polyline
Do you want to turn it into one? <Y>
Enter an option [Close/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype
17
gen/Undo]: join
Select objects: Specify opposite corner: 0 found
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects:
2 segments added to polyline
Enter an option [Close/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype
gen/Undo]: join
Select objects: 1 found
Command: extrude
Current wire frame density: ISOLINES=4
Command: extrude
Current wire frame density: ISOLINES=4
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects:
Specify height of extrusion or [Path]: path
Select extrusion path:
Copiem flanşa de jos într-un plan din imediata apropiere a primei flanşe
Din desenul de execuţie al piesei se constată că flanşele de prindere sunt identice. Pentru a scurta timpul de
modelare se va copia flanşa deja modelată, copia urmând a fi poziţionată la celălalt capăt, din dreapta al
racordului.
Command: Copy
Select objects: 1 found
Select objects:
Specify base point or displacement, or [Multiple]: Specify second point of
displacement or <use first point as displacement>: *Cancel*
Command: copy
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
18
Select objects:
Această poziţionare se poate efectua în mai multe feluri, dar cel mai simplu este prin utilizarea comenzii ALIGN.
Comanda ALIGN -Această comandă permite mutarea flanşei copiate în capătul racordului extrudat folosind
două perechi de puncte. Prima pereche de puncte va fi centru cercului superior al flanşei copiate şi cel de-al doilea
punct vafi centrul carcului racordului unde vom amplasa flanşa. A doua pereche de puncte va fi centrul cercului
inferior al flanşei şi un punct de pe generatoarea *calea de extrudare* - indiferent unde ar fi acesta.
Command: align
Select objects: 1 found
Select objects:
Specify first source point:
Specify second destination point:
Specify third source point or <continue>:
Scale objects based on alignment points? [Yes/No] <N>:
Pentru a aplica alte metode de poziţionare a flanşei se poate face apel la utilizarea comenzilor ROTATED şi
MOVE în spaţiul tridimensional.
În urma aplicării acestei comenzi, flanşa copiată este poziţionată corect la capătul din dreapta al racordului, aşa
cum rezultă din figura de mai jos. Totodată în această etapă se elimină polilinia creată, rolul său fiind incheiat.
După desfăşurarea etapelor de modelare a rezultat conform desenului, că există următoarele 4 solide componente:
două flanşe identice şi două corpuri sub formă tubulară, mcurbate, unul interior iat celălalt exterior. Pentru a avea
un singur solid, sunt necesare două operaţii booleane: de uniune între corpul exterior şi cele 2 flanşe, obţinându-
se, astfel, un solid nou, apoi o extragere din aceasta a corpului interior. Uniunea se realizează folosind comanda
UNION, se selectează cele 3 solide amintite anterior şi se obţine corpul din figura de mai jos.
Comanda Union- se vor uni doar 3 elemente cu această comandă – flanşa de jos, racordul exterior şi flanşa
copiată
Command: union
Select objects: 1 found
Select objects: 1 found, 2 total
19
Select objects: 1 found, 3 total
Select objects:
Extragerea utilizează comanda SUBTRACT, rezultatul aplicării sale fiind un corp solid ca în figua de mai jos.
Command: subtract
Select solids and regions to subtract from ..
Select objects: 1 found
Select objects:
Select solids and regions to subtract ..
Select objects: 1 found
Select objects:
Command: hide
Regenerating model.
Command: shade
20
Prezentarea şi verificarea interiorului piesei se poate realiza prin comanda SLICE planul de secţionare fiind XY.
În urma secţionării s-a înlăturat jumătate din corpul racordului, cea aflată în direcţia pozitivă a axei Z. Conform
reprezentării din figură rezultă că racordul este un singur corp solid.
Command: Slice
Select objects:
Specify first point on slicing plane by [Object/Zaxis/View/XY/YZ/ZX/3points]
<3points>: 3point
Specify first point on plane:
Specify second point on plane:
Specify third point on plane:
Specify a point on desired side of the plane or [keep Both sides]:
The point should not be on the slicing plane
Specify a point on desired side of the plane or [keep Both sides]:
21