Documente Academic
Documente Profesional
Documente Cultură
Infografica - Initiere in Autocad
Infografica - Initiere in Autocad
CUPRINS
CUPRINS...............................................................................................................................1
INTRODUCERE..................................................................................................................3
Cap.1 Elemente de baz ale AutoCAD ului.....................................................................4
1.1 Deschiderea sesiunii de lucru.....................................................................................4
1.2 Prezentarea ecranului de desenare..............................................................................6
1.3 Introducerea comenzilor.............................................................................................8
1.4 Sisteme de coordonate................................................................................................9
1.5 Introducerea datelor..................................................................................................10
1.6 nchiderea sesiunii de lucru......................................................................................13
Cap.2 Comenzi de iniializare i ajutoare grafice............................................................15
2.1. Comanda GRID........................................................................................................15
2.2. Comanda ORTHO....................................................................................................15
2.3. Comanda OSNAP.....................................................................................................16
2.4. Comanda LIMITS....................................................................................................17
2.5. Comanda PAN..........................................................................................................18
2.6. Comanda REDRAW.................................................................................................18
2.7. Comanda SNAP........................................................................................................19
2.8. Comanda UCS..........................................................................................................19
2.9. Comanda VIEW.......................................................................................................21
2.10. Comanda VIEWERS................................................................................................21
2.11. Comanda ZOOM......................................................................................................22
2.12. Comanda UNITS......................................................................................................24
Cap.3 Comenzi de desenare...............................................................................................25
3.1. Comanda LINE..........................................................................................................25
3.2. Comanda CIRCLE.....................................................................................................27
3.3. Comanda XLINE (construction line).........................................................................29
3.4. Comanda MLINE (multiline).....................................................................................30
3.5. Comanda PLINE (polyline).......................................................................................31
3.6. Comanda ARC...........................................................................................................33
3.7. Comanda ELLIPSE ARC...........................................................................................36
3.8. Comanda ELLIPSE....................................................................................................36
3.9. Comanda DONUT.....................................................................................................38
*Diametrul median este de 31 mm....................................................................................38
3.10. Comanda RECTANGLE..........................................................................................39
3.11. Comanda POLYGON...............................................................................................40
3.12. Comanda TRACE....................................................................................................41
3.13. Comanda SPLINE....................................................................................................42
3.14. Comanda SKETCH..................................................................................................43
3.15. Comanda POINT......................................................................................................44
1
INTRODUCERE
Munca de proiectare a unui inginer nu mai poate fi conceput n afara
calculatorului, indiferent de specializare reprezentrile virtuale devenind
limbajul curent de exprimare. ncepnd din faza conceptual pn la etapa de
manufacturare, desenul n plan, dar mai ales modelarea solidelor sunt necesare
n toate etapele de elaborare i promovare a unui produs.
Aceast lucrare propune cititorului iniierea n mediul de programare
asistat AutoCAD 2002 prin intermediul unor teme a cror rezolvare este
prezentat pas cu pas, integrnd treptat comenzile specifice, pentru temele finale
fiind oferite numai sugestii generale de rezolvare.
Datorit faptului c temele prezint gradat majoritatea aspectelor
legate de utilitarul AutoCAD 2002, acest curs poate fi de folos oricui dorete
s abordeze proiectarea asistat, att de ctre nceptori ct i de iniiai,
pentru care sunt prezentate informaii legate de setri, variabile de sistem i
mod de lucru, pe tematici.
Este de reinut c, n general, utilizarea calculatorului n proiectare
este o alegere care ofer aproape ntotdeauna mai multe soluii. De aceea,
cititorii sunt invitai s gseasc i alte ci de rezolvare a temelor. Algoritmii
prezentai sunt orientativi. Ei sunt doar structuri de baz care ajut la
desvrirea temei.
Icon AutoCAD
Desen nou
Desen
existent
Meniuri
Meniuri
Zona de desenare
Cursor grafic
Sistemul de
coordonate
Linia de
comand
Bara de
stare
Nume
Utilizare
New
Open
Save
Print preview
Spelling
Cut
Copy
Paste
Match
Properties
Undo, Redo
Launch
Browser
Osnap
Legarea de obiecte
UCS
Distance
Redraw View
Aerial View
Named View
Pan
Zoom
a.
b.
Fig.1.7
10
12
14
Comanda GRID
Comanda ORTHO
15
Command: ORTHO
ON/OFF<implicit>:modul ortho se activeaz (ON), respectiv
dezactiveaz (OFF);
De asemenea, se poate activa/dezactiva modul ORTHO tastnd F8.
2.3.
Comanda OSNAP
Folosind comanda OSNAP putem alege una sau mai multe setri
pentru object snap, nainte de utilizarea unei comenzi de desenare sau de
editare. Modurile object permit poziionarea cursorului ntr-o anumit parte
a unei entiti sau ntr-un punct care este ntr-o relaie spaial specific cu
entitatea. Dialogul decurge astfel:
Command: OSNAP
Apare fereastra de dialog Drafting Settings n care este selectat
opiunea Object Snap.
- endpoint;
- midpoint;
- center;
- node;
- quadrant;
- intersection;
- perpendicular;
- tangent;
- intersecie aparent;
- none.
Din fereastra de dialog se selecteaz opiunile dorite cu care se va
lucra pe tot parcursul desenului curent.
2.4.
Comanda LIMITS
Comanda PAN
Comanda REDRAW
2.7.
18
Comanda SNAP
Comanda UCS
20
Comanda VIEW
2.10.
Comanda VIEWERS
21
Comanda ZOOM
22
23
Command: ZOOM
All//<nX/nXP>:0.5xp
vederea din viewport-ul respectiv va fi redesenat n spaiul hrtie cu un
factor de scalare de 1:2. Cnd se ploteaz desnul din spaiul hrtie n mrime
natural, vederea plan rezultat va fi plotat la scara 1:2.
2.12.
Comanda UNITS
Precizia
Unitatea de msur
Fig. 2.1 Fereastra de dialog pentru comanda UNITS
24
26
27
a.
b.
Fig. 3.3 Cercuri desenate cu comanda CIRCLE
c.
~ 2P (dou puncte)
command: circle
3P/2P/TTR/<Circle point>: 2P
First point on diameter: se dau coordonatele primului punct
Second point on diameter: se dau coordonatele ceui de-al doilea
punct
~ 3P (trei puncte) (figura 3.3.b)
command: circle
3P/2P/TTR/<Circle point>: 3P
first point: coordonatele primului punct
second point: coordonatele celui de-al doilea punct
third point: coordonatele celui de-al treilea punct
~ TTR ( Tangent-Tangent-Raz) (figura 3.3.c)
command: circle
3P/2P/TTR/<Circle point>: TTR
Enter Tangent spec: se selecteaz prima entitate de tangen
Enter second Tangent spec: se selecteaz a doua entitate de tangen
Radius: 30
28
Trough point
Angle start
Bisect
Angle vertex
Angle end
29
distance
Offset
Object
30
Next
point
Next
point
Start point
Close
Direction
End
point
CEnter
End
point
Second
point
Start
point
Ending
width
Starting
width
Fill off
32
Fill on
Command: ARC
Specify start point or [Center]: c
Specify center point of arc: O
Specify start point of arc: M
Specify end point of arc or [Angle/chord Length]: N
33
Center
End
point
Start
point
Command: ARC
Specify start point or [Center]: c
Specify center point of arc: O
Specify start point of arc: P
Specify end point of arc or [Angle/chord Length]: a
Specify included angle: alfa (450)
Center
Angle
Start
point
Command: ARC
Specify start point or [Center]:c
Specify center point of arc: O
Specify start point of arc: M
Specify end point of arc or [Angle/chord Length]: L
Specify length of chord: lungime coard
Center
Start
point
34
Command: ARC
Specify start point or [Center]: D
Specify second point or [Center/End]: e
Specify end point of arc: E
Specify center point of arc or [Angle/Direction/Radius]: d
Specify tangent direction for the start point of arc:
Direction
Start
point
End
point
Command: ARC
Specify start point or [Center]: V
Specify second point or [Center/End]: e
Specify end point of arc: S
Specify center point of arc or [Angle/Direction/Radius]: r
Specify radius of arc: raza arcului
Start
point
End
point
35
Start
angle
Axis
endpoint 2
Axis
endpoint 1
End
angle
36
20
Axis
endpoint A
Axis
endpoint B
Command: ELLIPSE
Specify axis end point of ellipse or [Arc/Center]: c
Specify center of ellipse: centrul elipsei
Specify other end point of axis: D
Specify distance to other axis or [Rotation]: distana (20)
Center
20
Distance
Axis
endpoint D
Command: ELLIPSE
Specify axis end point of ellipse or [Arc/Center]: E
Specify other end point of axis: F
Specify distance to other axis or [Rotation]: r
Specify rotation around major axis: unghiul de rotaie fa de poziia
cercului a crui proiecie este elipsa (45)
37
Axis
endpoint E
Axis
endpoint F
38
Center (P)
Other
corner B
First
corner A
[Chamfer/Elevation/Fillet/Thickness/Width]: w
Specify line width for rectangles <0.00>: 0.3
Specify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]: A
Specify other corner point or [Dimensions]: B
39
Inscris in cerc
Center
40
Circumscris cercului
Center
Start
point A
Next
point B
Next
point C
41
42
Next
point
First
point
3.14. Comanda SKETCH
Aceast comand deseneaz linii de ruptut, formate din segmente.
Command: SKETCH
Record increment <0.1>: mrimea segmentelor care compun linia
Sketch. Pen eXit Quit Record Erase Connect .
Opiuni:
-
43
44
Afiare pe ecran
45
46
Modul de selectare
Afiare
Selectare individual
Selectare Window
47
Selectare Crossing
Selectare WPolygon
Selectare CPolygon
Selectare Fence
Atunci cnd sunt selectate, obiectele sunt evideniate prin afiarea lor
cu linie ntrerupt.
O alt posibilitate de selectare a obiectelor, n vederea editrii
acestora, este cu ajutorul unor puncte de prindere numite grip uri. Aceste
grip uri sunt selectori care apar, n poziii specifice, pe entitile desenate, o
dat cu selectarea acestora direct la promptul Command: (nici o comand
nu este activ) fig. 4.2.
Grip urile apar ca nite ptrele transparente, de culoare albastr,
devenind roii i opace atunci cnd sunt selectate prin editare, respectiv
verzi, atunci cnd mouse-ul se afl deasupra lor, fr a le selecta. Selectarea
48
unui grip se ace prin punctare cu mouse-ul. Se pot selecta mai multe grip
uri innd apsat tasta <Shift>.
Dupa
Punctul
de baza
Punctul
secund
52
Inainte
Dupa
Distance
Punctul
dat
53
54
20
20
56
Punctul
de deplasare
Punctul
nou
57
Inainte
Dupa
Command: SCALE
Select objects: selectai obiectele;
Select objects: enter (pentru a ncheia selecia);
Specify base point: specificai punctul fa de care scalai obiectele
selectate;
Specify scale factor or [Reference]: scpecificai factorul de scar sau
[Referina]
Reference permite scalarea fa de o dimensiune de referin.
5.9. Comanda TRIM
Cu aceast comand se reteaz poriuni ale obiectelor desenate,
dincolo de o muchie tietoare (frontier).
- pictograma comenzii TRIM
Command: TRIM
Select cutting edges
Select objects: selectai obiectele;
Select objects: enter (pentru a ncheia selecia);
Select objects to trim or shift - select to extend or [Project/Edge/Undo]:
selectai obiectele de tiat sau [Project/Edge/Undo]
Select objects to trim or shift - select to extend or [Project/Edge/Undo]:
enter (pentru a ncheia comanda)
Opiuni:
Project specific modul de aciune a comenzii, atunci cnd obiectul
selectat intersecteaz frontiera;
Edge specific modul de aciune a comenzii, atunci cnd obiectul selectat
nu intersecteaz frontiera;
Undo anuleaz ultima aciune de retezare.
Opiuni pentru Project:
None n spaiul tridimensional;
UCS n planul orizontal al UCS ului curent;
View n vederea curent.
59
Inainte
Dupa
Inainte
Dupa
61
Command: BREAK
Select object: selectai obiectul din care dorii s eliminai o poriune;
Specify second break point or [First point]: specificai al doilea punct de
eliminare sau [specificai primul punct] f
Specify first break point: specificai primul punct de eliminare;
Specify second break point: specificai al doilea punct de eliminare.
5.12. Comanda CHAMFER
Cu aceast comand se realizeaz teirea unui contur sau a unui col.
- pictograma comenzii CHAMFER
Command: CHAMFER
(Trim mode) Current chamfer Dist1 = 2.50 Dist2 = 2.50 distanele curente
sunt Dist1 = 2,5 mm i Dist2 = 2,5 mm
Select first line or [Polyline/Distance/Angle/Trim/Methoe]: selectai prima
linie sau [Polilinia/Distana/Unghiul/Tiere/Metoda];
Select second line: selectai a doua linie;
Opiuni:
Polyline teete toate colurile unei polilinii;
Distance se definesc distanele de teire (Dist1, Dist2);
Angle stabilete unghiul de teire;
Trim controleaz modul de afiare a teiturii: Trim elimin segmentele
dintre intersecia liniilor teite i punctele de unde ncepe teitura;
No trim nu elimin acele segmente (deci, liniile teite vor fi
pstrate intact i v-a aprea i teitura)
Method controleaz metoda de definire a teiturii; prin dou distane sau
printr-o distan i un unghi.
62
Inainte
Dupa
63
Inainte
Dupa
Fara taiere
R2
Cu taiere
R2
64
65
66
Fit deseneaz o curb format din arce de cerc; curba trece prin toate
vrfurile (punctele de capt ale segmentelor componente ale
poliliniei;
2)
3)
4)
5)
6)
69
70
Dupa
73
74
75
Command: area
Specify first corner point or [Object/Add/Subtract]: A
Specify next corner point or press ENTER for total: B
Specify next corner point or press ENTER for total: C
Specify next corner point or press ENTER for total: D
Specify next corner point or press ENTER for total: E
Specify next corner point or press ENTER for total: A
Specify next corner point or press ENTER for total: enter
Area = 2139.88, Perimeter = 176.34
76
Fig.5.26.1.a
Fig.5.26.1.b
77
Fig.5.26.2
Hatch
permite
Fig.5.26.3
80
2. Comanda Mtext
Aceast comand permite plasarea n desen a unui ntreg paragraf de
text, ntr-un spaiu definit de utilizator, ntreg textul paragrafului fiind
considerat ca o entitate. Textul dorit se poate introduce direct de la tastatur,
se poate importa dintr-un editor de text sau se poate copia folosind memoria
Clipboard, prin procedee de tip Cut/Paste.
Command: Mtext
Current text style: stilul curent Text height: valoarea curent
(Stilul textului curent
nlimea textului)
Specify first corner: specificai primul col;
Specify
opposite
corner
or
[Height/Justify/Line
spacing/Rotation/Style/Width]: specificai colul opus sau [opiuni];
Opiunile comenzii Mtext sunt:
1. Height nlimea textului;
83
Colul opus
Simbolul
Simbolul pentru grade (0)
%%p
%%c
85
40
20
la
20
15
lc
5
R5
elc
Fig.7.1 Elementele cotrii
86
li
Pentru crearea unui stil nou de cotare se acioneaz butonul New din
fereastra Dimension Style Manager, buton care permite deschiderea unei
alte ferestre de dialog, Create New Dimension Style, figura 7.3.
88
Fig.7.5 Fereastra
New Dimension
Style: nume stil,
pentru stabilirea
liniilor de cot i
extrimitilor
acestora,
Lines
and Arrow
89
Fig.7.6 Fereastra
New Dimension
Style: nume stil,
pentru seciunea
Fit
Fig.7.7 Fereastra
New Dimension
Style: nume stil,
pentru seciunea
Primay Units
90
91
Exit
REDraw
STAtus
STYle
Undo sau U
OVeride
REStore
Save
VAriables
HOMetext
Newtext
OBlique
TEdit
TRotate
UPdate
92
Comenzi utilitare
Determin prsirea sesiunii de cotare, revenind la promptul
Command:
Redeseneaz fereastra de afiare curent
Listeaz parametrii cureni ai tuturor variabilelor de cotar
Stabilete stilul textului cotei
Determin anularea ultimei operaii de cotare
Comenzi pentru controlul stilului
Modific parametrii variabilelor de cotare pentru cotele
selectate
Stabilete un stil de cotare definit anterior i salvat cu Save;
pentru a vedea diferenele dintre stilul de cotare curent i un
alt stil, numele acestuia din urm va fi tastat, precedat de
caracterul ~
Salveaz un stil de cotare sub un anumit nume
Listeaz valorile variabilelor de cotare, pentru un stil
specificat
Comenzi de editare a cotelor
Readuce textul deplasat al unei cote la poziia iniial
Modific textul cotelor
Stabilete un unghi de nclinare pentru liniile ajuttoare
Permite schimbarea poziiei i a unghiului textului cotei
Modific orientarea textului cotei
Acioneaz asupra cotelor deja desenate, modificndu-le la
parametrii cureni
ALigned
ANgular
Permite
unghiurilor
cotarea
Baseline
Permite cotarea fa de
aceeai baz de cotare
14
5
CEnter
Permite
marcarea
centrului unui cerc sau
arc de cerc
COntinue
20
15
93
Diameter
Permite
diametrelor
cotarea
HORizontal
Leader
Permite
construirea
liniilor de indicaie
ORdinate
Permite
cotarea
coordonate
15
TEXT
n
27.77
13.88
RAdius
64.59
Vertical
15
10
ROtated
94
77.48
12.89
Variabila de cotare
Dimassoc
Dimasz
Dimblk
Dimcen
Dimexe
Dimgap
Dimrnd
Dimscale
Dimstyle
Dimtad
Dimtih
Dimtoh
Dimtol
Dimtm
Dimtp
Dimtsz
Dimtxt
Efectul acesteia
Controleaz generarea cotelor asociative
Stabilete mrimea sgeii de cot
Permite inserarea unui bloc n locul sgeilor de
cot
Controleaz mrimea marcajului pentru centrul
cercurilor sau arcelor de cerc
Stabilete cu ct depete linia ajuttoare linia
de cot
Stabilete distana dintre linia de cot i textul
cotei
Rotunjete valorile cotelor inserate
Scaleaz toate elementele cotei
Numele stilului curent de cotare
Stabilete plasarea textului deasupra liniei de
cot
Controleaz orientarea textului cotei, atunci
cnd este scris ntre liniile ajuttoare, respectiv
n afar
Controleaz afiarea toleranelor, dup stabilirea
anterioar a lui Dimtm i Dimtp
Stabilete valoarea abaterii inferioare a cotei
Stabilete valoarea abaterii superioare a cotei
Stabilete mrimea extremitilor de tip linie
oblic, pentru liniile de cot
Stabilete nlimea textului cotei
Pictograma
96
Comanda
Linear Dimension
Efectul comenzii
Cotare liniar
Aligned
Dimension
Ordinate
Dimension
Aliniaz cota
Radius Dimension
Coteaz raze
Diameter
Dimension
Angular
Dimension
Quick Dimension
(Qdim)
Baseline
Dimension
Coteaz diametre
Cotare n coordonate
Coteaz unghiuri
Coteaz rapid obiecte
Coteaz fa
singur baz
de
Continue
Dimension
Quick Leader
Tolerance
Center Mark
Dimension Edit
Coteaz n serie
Coteaz prin linie de
indicaie
Introducerea
de
tolerane geometrice
Marcheaz centrul unui
cerc sau arc de cerc
Editeaz cote
Dimension
Text Editeaz textul cotei
Edit
Dimension Update Actualizeaz cote
Dimension Style Stabilete stilul de
Control
cotare
Dimension Style
Creeaz i modific
stilul de cotare
Pentru modificarea textului cotei se poate face i prin comanda
Ddedit.
De asemenea, editarea cotelor se poate realiza prin comanda
Dimedit. Aceasta permite schimbarea textului cotei, rotirea acestuia,
readucerea n poziia iniial sau nclinarea liniilor ajuttoare ale cotei. La
promptul comenzii, pentru a roti sau modifica textul cotei se defete mai
nti modificarea dorit i apoi se selecteaz dimensiunile asupra crora
opereaz modificarea.
97
Aplicaie
Comenzi noi
dim
linear horizontal, vertical i aligned
diameter
continue i baseline
angular
leader
radius
Procedura de desenare
1. ncepei un nou desen numit DIM1 bazat pe prototipul PIES. Pe
ecran vor fi observate trei proiecii ale unei piese turnate ce a fost ncrcat.
Asigurai-v c modurile grid i snap au fost activate.
2. Din meniul derulant Tools alegei
Toolbars/Dimensioning
.
3. Mrii zona proieciei frontale a piesei turnate ca n figura 1, folosind
comanda Zoom Window
din toolbar-ul Standard. Lsai suficient
spaiu n jurul proieciei pentru a putea aduga cotele.
Figura 1
99
100
Figura 2
8. Selectai Aligned Dimension a toolbar-ului Dimensioning. Aceasta
v permite s adugai dimensiuni (cote) liniare nclinate. Se dimensioneaz
acum cavitatea din partea stng a piesei turnate, ca n figura 3. Setai
locaia liniei de cot la aproximativ 30 mm de marginea proieciei.
Figura 3
Dimensionarea cercurilor
Pentru a completa dimensionarea acestei proiecii trebuie adugate
cotele celor dou cercuri.
9. Din toolbar-ului Dimensioning selectai Diameter Dimension
101
Figura 4
n linia de comand va apare cererea de selectare a arcului sau cercului
ce urmeaz a fi cotat. Selectai cercul exterior al piesei ntr-o poziie
corespunztoare orei 1 pe cadranul unui ceasornic. Prin deplasarea mouseului putei modifica poziia cotei diametrului.
Figura 5
102
Figura 6
Se poate observa acum c o imagine a cotei de diametru apare pe ecran,
dup care putei regla locaia textului n mod dinamic, ca n figura 4.
10. Cotai cercul mai mic n acelai mod, selectndu-l ntr-un punct
corespunztor poziiei orei 11 a unui ceasornic.
Figura 7
11. Folosind comanda zoom all vizualizai ntregul desen dup care cu
zoom window mrii proiecia lateral a piesei turnate aa cum este artat n
103
Figura 8
104
Figura 9
Figura 10
105
Figura 11
Selectai colul din dreapta sus al bosajului piesei turnate, ca n figura
10. Cota de 150 mm va fi creat cu caracteristici comune cotei de 15 mm.
14. Alegei al doilea punct n partea superioar a bosajului piesei.
Confirmai valoarea cotei terminnd cotarea cu aceast baz (vezi figura
11).
15. Trasai cota orizontal de 69 mm ce reprezint lungimea bosajului,
ca n figura 12.
Trasarea cotelor unghiulare (angular)
16. Selectai Angular Dimension
. Apsai <Return> pentru a putea
specifica punctele necesare cotei unghiulare. La prima cerere a punctelor ce
definesc unghiul selectai punctul n care nervura nclinat ntlnete baza
piesei turnate. Dac este necesar, urmrii figura 12 pentru a identifica
punctele ce trebuiesc selectate. La cererea primei extremiti a unui bra al
unghiului alegei captul de sus al liniei nclinate. Introducei extremitatea
106
Figura 12
celui de-al doilea bra al unghiului alegnd un punct oarecare pe verticala ce
trece prin vertex, cu ajutorul modului ortho. Cota unghiular va fi trasat ca
n figura 12.
Figura 13
Figura 14
Cotarea leader
17. Dai comanda Zoom Window
figura 13.
107
Figura 15
19. Mrii ntregul desen cu comanda Zoom All.
Cotarea razelor
20. Folosii zoom window pentru a crea o imagine similar celei din
figura 15.
21. Selectai opiunea Radius Dimension
. Opiunea Radius
lucreaz n acelai mod cu Diameter. La cererea arcului sau cercului ce
trebuie dimensionat, selectai cercul din dreapta sus ntr-un punct
corespunztor orei 1 de pe cadranul unui ceas. Introducei cota R5 i
108
Figura 16
Figura 17
109
Fig.8.2
Fereastra
Layer
Properties
Manager
110
Fig.8.3
Fereastra
Properties Manager
Layer
Fig.8.4 Seciunea
Show/Hide Details
113
Plot style se poate asocia unui strat un stil de tiprire, definit anterior;
Plot/Dont Plot se pot stabili straturi care vor fi sau nu tiprite.
La nceperea unui desen, este creat automat stratul 0, care nu poate fi
ters sau redenumit. Proprietile implicite ale acestui strat sunt: culoarea cu
numrul de cod 7 (alb sau negru, depinznd de culoarea de fond a spaiului
de lucru), tip de linie continu (continuous), grosimea liniei implicit
(0,01 inch sau 0,25 mm) i stilul de plotare normal.
114
Cap.9 Aplicaii
1.
115
Command: Line
Specify first point: 20,10
Specify next point or [Undo]: 20,287
Specify next point or [Undo]: enter (esc)
Se ncepe desenarea indicatorului. Prima dat se deseneaz conturul
exterior al acestuia. Dimensiunile de gabarit ale indicatorului sunt: lungime
= 180 i nlime = 40.
Command: Line
Specify first point: 230,10
Specify next point or [Undo]: 230,50
Specify next point or [Undo]: 410,50
Specify next point or [Undo]: enter
Pentru desenarea celorlalte linii componente ale indicatorului se
folosesc comenzile: offset, trim i extend.
Command: Offset
Specify offset distance or [Through] <1.00>: 60
Select object to offset or <exit>: P1
Specify point on side to offset: P2
Select object to offset or <exit>: enter
117
Command: Trim
Current settings : Projection = UCS, Edge = None
Select cutting edges
Select objects: P5
Select objects: 1 found
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/None]: P6
Select object to trim or shift-select to extend or [Project/Edge/None]: P7
Select object to trim or shift-select to extend or [Project/Edge/None]: enter
Command: Offset
Specify offset distance or [Through] <16.00>: 4
Select object to offset or <exit>: P4
Specify point on side to offset: P8
Specify point on side to offset: P9
Specify point on side to offset: P10
Select object to offset or <exit>: enter
118
Command: Trim
Current settings : Projection = UCS, Edge = None
Select cutting edges
Select objects: P2
Select objects: 1 found
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/None]: D1
Select object to trim or shift-select to extend or [Project/Edge/None]: D2
Select object to trim or shift-select to extend or [Project/Edge/None]: D3
Select object to trim or shift-select to extend or [Project/Edge/None]: enter
nainte de comanda Trim
119
Command: Offset
Specify offset distance or [Through] <4.00>: 9
Select object to offset or <exit>: P5
Specify point on side to offset: D4
Specify point on side to offset: D5
Select object to offset or <exit>: enter
Command: Trim
Current settings : Projection = UCS, Edge = None
Select cutting edges
Select objects: P2
Select objects: 1 found
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/None]: D4
Select object to trim or shift-select to extend or [Project/Edge/None]: enter
Command: Trim
Current settings : Projection = UCS, Edge = None
Select cutting edges
120
Select objects: P3
Select objects: 1 found
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/None]: D5
Select object to trim or shift-select to extend or [Project/Edge/None]: enter
Dup comanda Trim
121
Command: Offset
Specify offset distance or [Through] <9.00>: 12
Select object to offset or <exit>: P5
Specify point on side to offset: M1
Select object to offset or <exit>: enter
Command: Trim
Current settings : Projection = UCS, Edge = None
Select cutting edges
Select objects: P3
Select objects: 1 found
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/None]: M2
Select object to trim or shift-select to extend or [Project/Edge/None]: enter
Pentru completarea indicatorului cu textul aferent se folosete
comanda Text.
Command: Text
Current text style: STANDARD Text height : 3.50
Specify start point of text or [Justify/Style]: j
Enter an option [Align/Fit/../BR]: f
Specify first endpoint of text baseline: T1
Specifyv second endpoint of text baseline: T2
Specify height <3.50>: 3.50
Enter text: Proiectat
Enter text: enter
122
Command: Text
Current text style: STANDARD Text height : 3.50
Specify start point of text or [Justify/Style]: j
Enter an option [Align/Fit/../BR]: f
Specify first endpoint of text baseline: T3
Specifyv second endpoint of text baseline: T4
Specify height <3.50>: 3.50
Enter text: Desenat
Enter text: enter
Command: Text
Current text style: STANDARD Text height : 3.50
Specify start point of text or [Justify/Style]: j
Enter an option [Align/Fit/../BR]: f
Specify first endpoint of text baseline: T5
Specifyv second endpoint of text baseline: T6
Specify height <3.50>: 3.50
Enter text: Verificat
Enter text: enter
Command: Text
Current text style: STANDARD Text height : 3.50
Specify start point of text or [Justify/Style]: j
Enter an option [Align/Fit/../BR]: f
Specify first endpoint of text baseline: T7
Specifyv second endpoint of text baseline: T8
Specify height <3.50>: 3.50
Enter text: Aprobat
Enter text: enter
Command: Text
Current text style: STANDARD Text height : 3.50
Specify start point of text or [Justify/Style]: j
Enter an option [Align/Fit/../BR]: f
Specify first endpoint of text baseline: T9
Specifyv second endpoint of text baseline: T10
123
124
125
2.
Command: Line
Specify first point: 56,155
Specify next point or [Close/Undo]: @0,-13
Specify next point or [Close/Undo]: enter
127
Command: Line
Specify first point: 56.9,155
Specify next point or [Close/Undo]: @0,-13
Specify next point or [Close/Undo]: enter
Command: Line
Specify first point: 58,155
Specify next point or [Close/Undo]: @0,-13
Specify next point or [Close/Undo]: enter
Command: Line
Specify first point: 61,155
Specify next point or [Close/Undo]: @0,-13
Specify next point or [Close/Undo]: enter
Command: Line
Specify first point: 86,157
Specify next point or [Close/Undo]: @0,-17
Specify next point or [Close/Undo]: enter
Command: Line
Specify first point: 87,163.5
Specify next point or [Close/Undo]: @0,-30
Specify next point or [Close/Undo]: enter
Command: Line
Specify first point: 244,133.5
Specify next point or [Close/Undo]: @0,25
Specify next point or [Close/Undo]: enter
128
Pentru a lucra mai uor mutm UCS din punctul curent n punctul de
coordonate 55,148.5, adic la intersecia dintre suprafaa frontal din stnga
a piesei i axa de simetrie a acesteia.
Command: UCS
Current UCS name: *World*
Enter an option [New/Move/ .] <World>: m
Specify new origin point or [Zdepth] <0,0,0>: 55,148.5
Se schimb stratul curent pe stratul Axa, pentru a desena cele dou
axe corespunztoare gurilor de M10 i apoi desenm axele respective.
Command: Line
Specify first point: 55,-20
Specify next point or [Close/Undo]: @0,40
Specify next point or [Close/Undo]: enter
Command: Offset
Specify offset distance or [Through] <0>: 120
Select object to offset or <exit>: P1
Select point on side to offset: P2
Select object to offset or <exit>: enter
Command: Line
Specify first point: 51,9
Specify next point or [Close/Undo]: @4,0
Specify next point or [Close/Undo]: enter
Se trece stratul curent pe stratul Linie subire.
Command: Line
Specify first point: 50,10
Specify next point or [Close/Undo]: @0,-25
Specify next point or [Close/Undo]: enter
Command: Mirror
Select objects: w
Specify first corner: N1
Specify opposite corner: N2
Select objects: enter
Specify first point of mirror line: D1
Specify second point of mirror line: D2
Delete source objects? [Yes/No] <N>: enter
Command: Spline
Specify first point or [Object]: T1
Specify next point: T2
Specify next point or [Close/Fit tolerance] <start tangent>: T3
Specify next point or [Close/Fit tolerance] <start tangent>: T4
Specify next point or [Close/Fit tolerance] <start tangent>: T5
Specify next point or [Close/Fit tolerance] <start tangent>: enter
Specify start tangent: enter
Specify end tangent: enter
Command: Mirror
Select objects: P1
Selects objects: enter
Specify first point of mirror line: R1 este mijlocul segmentului de dreapt
Specify second point of mirror line: R2
Delete source objects? [Yes/No] <N>: enter
131
132
3.
60
=
20
40
15
5 1
0 10
10
25
10
7,5
10 10
15
50
Fig. 9.3
133
Command: Line
Specify first point: 0.00,-138.5
Specify next point or [Undo]: @0,277
Specify next point or [Undo]: enter
Command: enter
Specify first point: -190, 0.00
Specify next point or [Undo]: @390,0
Specify next point or [Undo]: enter
Din desenul piesei vedem c cele 3 proiecii au urmtoarele cote de
gabarit:
- proiecia principal: L = 70; h = 30;
- proiecia din stnga: L = 60; h = 30;
- proiecia de sus: L = 70; h = 60.
Trasm cele 3 dreptunghiuri n care se vor ncadra proieciile
respective, lsnd fa de liniile desenate anterior cte 20 mm.
Command: Offset
Specify offset distance or [Through] <1.00>: 20
Select object to offset or <exit>: P
Specify point on side to offset: P1
Select object to offset or <exit>: P
Specify point on side to offset: P2
Select object to offset or <exit>: D
Specify point on side to offset: D1
134
136
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: D5, D6, D7, D8, D9, D10
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: D2
Select object to trim or shift-select to extend or [Project/Edge/Undo]: D4
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T1
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T2
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T3
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T4
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T5
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T6
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T7
Select object to trim or shift-select to extend or [Project/Edge/Undo]: T8
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
137
139
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: N5, N6, N7
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: N7
Select object to trim or shift-select to extend or [Project/Edge/Undo]: N8
Select object to trim or shift-select to extend or [Project/Edge/Undo]: N9
Select object to trim or shift-select to extend or [Project/Edge/Undo]: N5
Select object to trim or shift-select to extend or [Project/Edge/Undo]: N6
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
Command: Offset
Specify offset distance or [Through] <15>: 10
Select object to offset or <exit>: Q1
Specify point on side to offset: Q2
Select object to offset or <exit>: enter
140
Command: enter
Specify offset distance or [Through] <10>: 25
Select object to offset or <exit>: Q1
Specify point on side to offset: Q2
Select object to offset or <exit>: enter
Command: enter
Specify offset distance or [Through] <25>: 35
Select object to offset or <exit>: Q3
Specify point on side to offset: Q2
Select object to offset or <exit>: enter
Command: Line
Specify first point: Q4
Specify next point or [Undo]: Q5
Specify next point or [Undo]: enter
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: Q6
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: Q7
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
Command: enter
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: Q8
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: Q9
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
141
Command: Erase
Select objects: Q8
Select objects: Q10
Select objects: enter
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: Q6, Q12
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: Q11
Select object to trim or shift-select to extend or [Project/Edge/Undo]: Q13
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: S1, S2
Select objects: enter
142
Command: Offset
Specify offset distance or [Through] <10>: 15
Select object to offset or <exit>: S1
Specify point on side to offset: S5
Select object to offset or <exit>: S2
Specify point on side to offset: S5
Select object to offset or <exit>: enter
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: S6, S7
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: S8
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
143
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: S6, S7, S11
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E1
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E2
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E3
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
144
Command: Offset
Specify offset distance or [Through] <15>: 10
Select object to offset or <exit>: E4
Specify point on side to offset: E6
Select object to offset or <exit>: E5
Specify point on side to offset: E6
Select object to offset or <exit>: enter
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: E7
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E8
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E9
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E10
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E11
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
145
Command: Offset
Specify offset distance or [Through] <10>: 15
Select object to offset or <exit>: F1
Specify point on side to offset: F3
Select object to offset or <exit>: F2
Specify point on side to offset: F3
Select object to offset or <exit>: enter
Se construiete o linie din punctul S4 perpendicular pe dreapta d1,
respectiv din punctul S5 perpendicular pe dreapta d2.
146
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: F1, F2
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: E7
Select object to trim or shift-select to extend or [Project/Edge/Undo]: F6
Select object to trim or shift-select to extend or [Project/Edge/Undo]: F7
Select object to trim or shift-select to extend or [Project/Edge/Undo]: F8
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
147
Command: Trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects: F9, F10, F11, F12
Select objects: enter
Select object to trim or shift-select to extend or [Project/Edge/Undo]: F9
Select object to trim or shift-select to extend or [Project/Edge/Undo]: F10
Select object to trim or shift-select to extend or [Project/Edge/Undo]: F11
Select object to trim or shift-select to extend or [Project/Edge/Undo]: G1
Select object to trim or shift-select to extend or [Project/Edge/Undo]: G2
Select object to trim or shift-select to extend or [Project/Edge/Undo]: G3
Select object to trim or shift-select to extend or [Project/Edge/Undo]: G4
Select object to trim or shift-select to extend or [Project/Edge/Undo]: G5
Select object to trim or shift-select to extend or [Project/Edge/Undo]: enter
148
149
Command: circle
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: G8
Specify radius of circle or [Diameter]: 10
Select objects: w
Specify first corner: Specify opposite corner: 41 found
Select objects: enter
Specify change point or [Properties]: p
Enter property to change [Color/Elev/LAyer/LType/ltScale/LWeight/
Thickness]: la
Enter new layer name <0>: linie groasa
Enter property to change [Color/Elev/LAyer/LType/ltScale/LWeight/
Thickness]: enter
151
Varianta
al
a
aa
ar
h, bh
br
cha
ch
c
col, colour,
ddcolor
co, cp
CUSTOMIZE
DDEDIT
DDPTYPE
DIM
DIM1
DIMALIGNED
152
ed
dal, dimali
Efectul comenzii
Afieaz informaii despre AutoCAD
Aliniaz obiectele n raport cu alte obiecte
Controleaz mrimea selectorului
Traseaz arce de cerc
Calculeaz aria
Realizeaz copii multiple, ntr-o reea
rectangular sau polar
Deschide fereastra Active Assistance
Verific desenul curent
Stabilete fundalul scenei
Haureaz un contur nchis
Controleaz afiarea marcatorilor punctelor
Elimin o parte dintr-o entitate
Teete muchiile i colurile obiectelor
Schimb proprietile obiectelor
Modific proprieti ale obiectelor: culoarea,
stratul, tipul, grosimea i factorul de scal
pentru linii, elevaia, grosimea
Deseneaz un cerc
nchide desenul curent
Stabilete culoarea
Copiaz obiecte
Copiaz obiecte cu punctul de start
preselectat
Definete meniuri mobile, butoane sau
combinaii de taste
Editeaz textul
Stabilete stilul i mrimea de afiare a
punctelor
Deschide sesiunea de cotare
Creeaz o singur cot
Creeaz o cot liniar, aliniat
DIMANGULAR
DIMBASELINE
DIMCENTER
DIMCONTINUE
DIMDIAMETER
DIMDISASSOCIATE
DIMEDIT
DIMLINEAR
DIMORDINATE
DIMOVERRIDE
DIMRADIUS
DIMREASSOCIATE
DIMREGEN
DIMSTYLE
DIMEDIT
DIST
DIVIDE
DONUT
DRAGMODE
DRAWORDER
DSETTINGS
dan, dimang
dba,
dimbase
dce
dco,
dimcont
ddi, dimdia
dda
ded, dimed
dli, dimlin
dor, dimord
dov,
dimover
dra, dimrad
dre
d, ddim, dst,
dimsty
dimted
di
div
do
dr
ds,
ddrmodes,
rm, se
DWGRPROPS
ELEV
ELLIPSE
ERASE
EXPLODE
el
e
x
EXTEND
ex
FILL
FILLET
GRID
GROUP
fi
g
153
HATCHEDIT
HELP <F1>
HIDE
he
HLSETTINGS
INSERT
JPGOUT
JUSTIFYTEXT
LAYER
hi
ddinsert, i
ddlmodes,
la
LAYERP
LAYERPMODE
LEADER
LENGTHEN
LIMITS
LINE
LINETYPE
LTSCALE
LWEIGHT
MEASURE
MENIU
MIRROR
MLEDIT
MLINE
MLSTYLE
MODEL
MOVE
MREDO
MSPACE
MTEXT
154
lead
len
l
lt, ltype,
ddltype
lts
lw,
lineweight
me
mi
ml
m
ms
t, mt
MULTIPLE
MVIEW
mv
MVSETUP
NEW
OFFSET
OOPS
OPEN
OPTIONS
ORTHO
OSNAP
PAN
PEDIT
PLINE
PLOT
POINT
POLYGON
PREFERENCES
PREVIEW
PROPERTIES
PROPERTIESCLOSE
PSPACE
PURGE
QDIM
QLEADER
QNEW
ddgrips, gr,
op, pr
ddosnap, os
p
pe
pl
print
po
pol
pre
ch,
ddchprop,
ddmodify,
mo, props
prclose
ps
pu
le
QSAVE
QSELECT
QTEXT
QUIT
RAY
RECOVER
exit
155
rec
REDO
REDRAW
REDRAWALL
ra
REGEN
REGENALL
REGENAUTO
re
rea
REGION
ROTATE
SAVE
SAVEAS
SCALE
SCALETEXT
SELECT
SNAP
SPLINE
SPLINEDIT
STATUS
reg
ro
sc
sn
spl
spe
STRETCH
STYLE
STYLESMANAGER
st
TEXT
TIME
TOLERANCE
TOOLBAR
TOOLPALETTES
TOOLPALETTESCLOSE
TRACE
TRIM
U
UCS
UCSICON
UCSMAN
156
tol
to
tr
u
Deseneaz un dreptunghi
Redefinete
o
comand
AutoCAD,
dezactivat prin comanda Undefine
Anuleaz efectul unei comenzi anterioare
Undo sau U
Redeseneaz fereastra curent, eliminnd
marcatorii
Redeseneaz toate ferestrele, eliminnd
marcatorii
Regenereaz fereastra curent
Regenereaz toate ferestrele
Controleaz regenerarea automat a
desenului
Creeaz o regiune
Rotete obiectele n jurul unui punct
Salveaz desenul
Salveaz desenul curent sub un nume nou
Scaleaz obiectele
Scaleaz texte
Creeaz o mulime de selecie
Controleaz saltul cursorului pe ecran
Deseneaz o curb spline
Editeaz o curb spline
Afieaz valoarea curent a parametrilor
AutoCAD
Permite deformarea unui obiect, ptrnd
legturile
Creeaz un stil de scriere
Afieaz caseta de control a stilului de
tiprire
Creeaz o linie de text
Afieaz timpul de editare
nscrie tolerane geometrice
Afieaz, ascunde i creeaz meniuri grafice
Deschide fereastra Tool Palettes
nchide fereastra Tool Palettes
Deseneaz linii cu grosime
Reteaz poriuni ale obiectelor
Anuleaz ultima comand
Controleaz sistemul de coordonate UCS
Controleaz vizibilitatea pictogramei UCS
Gestioneaz UCS urile definite
UNDEFINE
UNDO
UNITS
VIEW
VIEWRES
XLINE
XPLODE
ZOOM
u
un, ddunits
ddview, v
xl
z
157
Bibliografie
158